Can Ozcan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Can Ozcan has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
J. Stewart Aitchison
Department of Electrical and Computer Engineering, University of Toronto, Toronto, ON, M5S 3G4, Canada
5 shared publicationsMo Mojahedi
Department of Electrical and Computer Engineering, University of Toronto, Toronto, ON, M5S 3G4, Canada
5 shared publications- J. Stewart Aitchison
Department of Electrical and Computer Engineering, University of Toronto, Toronto, ON, Canada
2 shared publications - Mo Mojahedi
Department of Electrical and Computer Engineering, University of Toronto, Toronto, ON M5S 3G8, Canada
2 shared publications
Latest Publications
- 1 January 2024
- Published by Optica Publishing Group
- p. SF3F.4
Ultrabroadband and Compact Silicon-to-Silicon Nitride Light Couplers
We demonstrate a significant length reduction for silicon- to-silicon nitride light couplers with experimentally measured losses below 0.1 dB over a 200 nm bandwidth for a device length of only 25 µm.
- 1 January 2024
- Published by Optica Publishing Group
- p. SF3F.4
Ultrabroadband and Compact Silicon-to-Silicon Nitride Light Couplers
We demonstrate a significant length reduction for silicon- to-silicon nitride light couplers with experimentally measured losses below 0.1 dB over a 200 nm bandwidth for a device length of only 25 µm.
- Open Access
Foundry-Processed Compact and Broadband Adiabatic Optical Power Splitters with Strong Fabrication Tolerance
Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, a broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well suited for mass production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we used a polynomial taper profile optimization algorithm to design 1 × 2 and 2 × 2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best-performing 1 × 2 and 2 × 2 power splitters had 20 m and 16 m coupling lengths, respectively. Our designs had minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across nine different chips showed excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1 × 2 and 2 × 2 adiabatic optical power splitters had excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements showed splitting ratios within 50 ± 3% over a 130 nm bandwidth. We also demonstrated the design of 1 × 2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.Open AccessFoundry-Processed Compact and Broadband Adiabatic Optical Power Splitters with Strong Fabrication Tolerance
Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, a broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well suited for mass production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we used a polynomial taper profile optimization algorithm to design 1 × 2 and 2 × 2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best-performing 1 × 2 and 2 × 2 power splitters had 20 m and 16 m coupling lengths, respectively. Our designs had minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across nine different chips showed excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1 × 2 and 2 × 2 adiabatic optical power splitters had excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements showed splitting ratios within 50 ± 3% over a 130 nm bandwidth. We also demonstrated the design of 1 × 2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%. - Open Access
- 18 October 2023
- Published by MDPI AG in Preprints.org
Foundry-processed Compact and Broadband Adiabatic Optical Power Splitters with Strong Fabrication Tolerance
Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.
- 18 October 2023
- Published by MDPI AG in Preprints.org
Open AccessFoundry-processed Compact and Broadband Adiabatic Optical Power Splitters with Strong Fabrication Tolerance
Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.
- 13 September 2023
- Published by Optica Publishing Group in Optics Letters
- Vol. 48 (18) , 4901-4904
Short, broadband, and polarization-insensitive adiabatic Y-junction power splitters
Adiabatic Y-junction power splitters have low loss, large bandwidth, high polarization insensitivity, and high tolerance to fabrication errors. However, the adiabatic transition lengths required are generally much longer than other power splitters. Using a nonlinear taper profile can considerably shorten the device length. Here, we introduce a taper profile optimization algorithm based on polynomial functions, which significantly reduces the lengths of the adiabatic power splitters without increasing losses. We experimentally demonstrate the performance of the adiabatic power splitters for minimum feature sizes of 80 nm, 120 nm, and 160 nm on the 220 nm silicon-on-insulator (SOI) platform. Our best device has a minimum feature size of 120 nm and a length of 14 µm, with measured losses of 0.25 dB and 0.23 dB for the transverse electric (TE) and transverse magnetic (TM) modes, respectively, in the 1500–1600 nm region. This device has an average transmission of −3 ± 0.5 dB in the 1500–1600 nm region, indicating highly balanced splitting over a large spectral range.
- 13 September 2023
- Published by Optica Publishing Group in Optics Letters
- Vol. 48 (18) , 4901-4904
Short, broadband, and polarization-insensitive adiabatic Y-junction power splitters
Adiabatic Y-junction power splitters have low loss, large bandwidth, high polarization insensitivity, and high tolerance to fabrication errors. However, the adiabatic transition lengths required are generally much longer than other power splitters. Using a nonlinear taper profile can considerably shorten the device length. Here, we introduce a taper profile optimization algorithm based on polynomial functions, which significantly reduces the lengths of the adiabatic power splitters without increasing losses. We experimentally demonstrate the performance of the adiabatic power splitters for minimum feature sizes of 80 nm, 120 nm, and 160 nm on the 220 nm silicon-on-insulator (SOI) platform. Our best device has a minimum feature size of 120 nm and a length of 14 µm, with measured losses of 0.25 dB and 0.23 dB for the transverse electric (TE) and transverse magnetic (TM) modes, respectively, in the 1500–1600 nm region. This device has an average transmission of −3 ± 0.5 dB in the 1500–1600 nm region, indicating highly balanced splitting over a large spectral range.
- 17 January 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (3) , 3579-3594
Optimization of bulk sensitivity for strip, slot, and subwavelength grating-based waveguides for dual-polarization operation
We propose a dual-polarization optimization method for the bulk sensitivity of silicon-on-insulator (SOI) waveguides by defining a multi-objective function that accounts for the substrate leakage losses. The proposed optimization method was used to design micro-ring resonator bulk sensors with strip, slot, subwavelength grating, and subwavelength grating slot waveguides. The subwavelength grating slot waveguide has a bulk sensitivity of 520 nm/RIU and 325 nm/RIU for the TE and TM modes, respectively, both of which are higher than the bulk sensitivities of strip, slot, and subwavelength grating waveguides. Moreover, our Monte Carlo analysis shows that the subwavelength grating slot waveguide has the highest immunity to fabrication errors.
- 17 January 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (3) , 3579-3594
Optimization of bulk sensitivity for strip, slot, and subwavelength grating-based waveguides for dual-polarization operation
We propose a dual-polarization optimization method for the bulk sensitivity of silicon-on-insulator (SOI) waveguides by defining a multi-objective function that accounts for the substrate leakage losses. The proposed optimization method was used to design micro-ring resonator bulk sensors with strip, slot, subwavelength grating, and subwavelength grating slot waveguides. The subwavelength grating slot waveguide has a bulk sensitivity of 520 nm/RIU and 325 nm/RIU for the TE and TM modes, respectively, both of which are higher than the bulk sensitivities of strip, slot, and subwavelength grating waveguides. Moreover, our Monte Carlo analysis shows that the subwavelength grating slot waveguide has the highest immunity to fabrication errors.
- 1 January 2023
- Published by Optica Publishing Group
- p. JW2A.79
Compact Adiabatic Power Splitters with Polynomial Taper Profile Optimization
We experimentally demonstrate profile-optimized adiabatic Y-branch power splitters with losses of 0.16 dB (TE) and 0.17 dB (TM) at 1,550 nm for 14 μm long devices with balanced power splitting between 1,500 and 1,600 nm.
- 1 January 2023
- Published by Optica Publishing Group
- p. JW2A.79
Compact Adiabatic Power Splitters with Polynomial Taper Profile Optimization
We experimentally demonstrate profile-optimized adiabatic Y-branch power splitters with losses of 0.16 dB (TE) and 0.17 dB (TM) at 1,550 nm for 14 μm long devices with balanced power splitting between 1,500 and 1,600 nm.
- 1 January 2021
- Published by Optica Publishing Group
- p. JW1A.40
Broadband Polarization Beam Splitter based on Tilted Subwavelength Gratings on the Si3N4/Si Augmented Low Index Guiding Platform
We demonstrate a polarization beam splitter based on the use of subwavelength gratings on an augmented low index waveguide. The design provides 25 dB extinction ratio with notable fabrication tolerance.
- 1 January 2021
- Published by Optica Publishing Group
- p. JW1A.40
Broadband Polarization Beam Splitter based on Tilted Subwavelength Gratings on the Si3N4/Si Augmented Low Index Guiding Platform
We demonstrate a polarization beam splitter based on the use of subwavelength gratings on an augmented low index waveguide. The design provides 25 dB extinction ratio with notable fabrication tolerance.