Atasi Dan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Atasi Dan has a total of 94 co-authors. Here are the top co-authors by number of shared publications:
- Harish Chandra Barshilia
Surface Engineering Division, CSIR-National Aerospace Laboratories, Bangalore, India
3 shared publications - Bikramjit Basu
Laboratory for Biomaterials Science and Translational Research, Materials Research Centre, Indian Institute of Science, Bangalore 560012, India
2 shared publications - Gabriel Alejandro Lopez
Physics Department, University of the Basque Country (UPV/EHU), Leioa, Spain
2 shared publications - Haixin Liu
National Institute of Standards and Technology
2 shared publications - Jizhao Zang
National Institute of Standards and Technology
2 shared publications John Lehman
2 shared publications
Latest Publications
- 7 April 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (8) , 2570-2573
Implementing photonic-crystal resonator frequency combs in a photonic foundry
We explore an AIM Photonics silicon nitride platform to fabricate photonic-crystal resonators (PhCRs) for generating optical parametric oscillators (OPOs) and soliton microcombs. Our approach leverages the scalability and fine feature size of silicon nitride processing on large-scale silicon wafers to achieve low-loss, high-Q microresonators, functionalized by nanoscale photonic-crystal structures. We demonstrate an intrinsic microresonator quality factor up to 1.2 × 107 with complete foundry fabrication on 300 mm silicon, a 700 nm thick silicon nitride device layer, and inclusion of complex nanophotonics. These features enable a host of nonlinear nanophotonic sources on the platform, including OPOs, microcombs, parametric amplifiers, squeezed-light generators, and single-photon sources. By fine-tuning the photonic-crystal design parameters, we achieve broad tunability in the frequency of the OPO output, spanning a significant portion of the near-infrared. Additionally, we observe the formation of soliton frequency combs, enabled by the precise dispersion engineering of the microresonators. These results highlight the potential of widely accessible, photolithographically patterned, silicon nitride photonics to enable wide access to and complex integration of frequency comb sources, with applications in spectroscopy, metrology, and communications.
- 7 April 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (8) , 2570-2573
Implementing photonic-crystal resonator frequency combs in a photonic foundry
We explore an AIM Photonics silicon nitride platform to fabricate photonic-crystal resonators (PhCRs) for generating optical parametric oscillators (OPOs) and soliton microcombs. Our approach leverages the scalability and fine feature size of silicon nitride processing on large-scale silicon wafers to achieve low-loss, high-Q microresonators, functionalized by nanoscale photonic-crystal structures. We demonstrate an intrinsic microresonator quality factor up to 1.2 × 107 with complete foundry fabrication on 300 mm silicon, a 700 nm thick silicon nitride device layer, and inclusion of complex nanophotonics. These features enable a host of nonlinear nanophotonic sources on the platform, including OPOs, microcombs, parametric amplifiers, squeezed-light generators, and single-photon sources. By fine-tuning the photonic-crystal design parameters, we achieve broad tunability in the frequency of the OPO output, spanning a significant portion of the near-infrared. Additionally, we observe the formation of soliton frequency combs, enabled by the precise dispersion engineering of the microresonators. These results highlight the potential of widely accessible, photolithographically patterned, silicon nitride photonics to enable wide access to and complex integration of frequency comb sources, with applications in spectroscopy, metrology, and communications.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS195_6
Dispersion-Engineered Ta2O5 with Ultralow-loss Cladding for Integrated Nonlinear Nanophotonics
We explore a Ta2O5 platform with ultralow-loss SiO2 cladding, enabling precise dispersion control for efficient soliton microcomb generation. This approach offers a robust foundation for fabrication of compact, high-performance, and scalable integrated photonics.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS195_6
Dispersion-Engineered Ta2O5 with Ultralow-loss Cladding for Integrated Nonlinear Nanophotonics
We explore a Ta2O5 platform with ultralow-loss SiO2 cladding, enabling precise dispersion control for efficient soliton microcomb generation. This approach offers a robust foundation for fabrication of compact, high-performance, and scalable integrated photonics.
- 1 July 2024
- Published by Elsevier in Applied Materials Today
- Vol. 39
From nano to giant grains: Optimizing Pt thermistors for microbolometers
- 1 July 2024
- Published by Elsevier in Applied Materials Today
- Vol. 39
From nano to giant grains: Optimizing Pt thermistors for microbolometers
- Open Access
- 1 February 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (2)
Photonic bandgap microcombs at 1064 nm
Microresonator frequency combs and their design versatility have revolutionized research areas from data communication to exoplanet searches. While microcombs in the 1550 nm band are well documented, there is interest in using microcombs in other bands. Here, we demonstrate the formation and spectral control of normal-dispersion dark soliton microcombs at 1064 nm. We generate 200 GHz repetition rate microcombs by inducing a photonic bandgap of the microresonator mode for the pump laser with a photonic crystal. We perform the experiments with normal-dispersion microresonators made from Ta2O5 and explore unique soliton pulse shapes and operating behaviors. By adjusting the resonator dispersion through its nanostructured geometry, we demonstrate control over the spectral bandwidth of these combs, and we employ numerical modeling to understand their existence range. Our results highlight how photonic design enables microcomb spectra tailoring across wide wavelength ranges, offering potential in bioimaging, spectroscopy, and photonic-atomic quantum technologies.
- 1 February 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (2)
Open AccessPhotonic bandgap microcombs at 1064 nm
Microresonator frequency combs and their design versatility have revolutionized research areas from data communication to exoplanet searches. While microcombs in the 1550 nm band are well documented, there is interest in using microcombs in other bands. Here, we demonstrate the formation and spectral control of normal-dispersion dark soliton microcombs at 1064 nm. We generate 200 GHz repetition rate microcombs by inducing a photonic bandgap of the microresonator mode for the pump laser with a photonic crystal. We perform the experiments with normal-dispersion microresonators made from Ta2O5 and explore unique soliton pulse shapes and operating behaviors. By adjusting the resonator dispersion through its nanostructured geometry, we demonstrate control over the spectral bandwidth of these combs, and we employ numerical modeling to understand their existence range. Our results highlight how photonic design enables microcomb spectra tailoring across wide wavelength ranges, offering potential in bioimaging, spectroscopy, and photonic-atomic quantum technologies.
- 11 January 2024
- Published by Elsevier in Applied Surface Science
- Vol. 652
High emittance plasma sprayed ZrO2-Y2O3/La2Zr2O7 thermal barrier coatings for potential application in scramjets
- 11 January 2024
- Published by Elsevier in Applied Surface Science
- Vol. 652
High emittance plasma sprayed ZrO2-Y2O3/La2Zr2O7 thermal barrier coatings for potential application in scramjets
- 17 February 2023
- Published by Elsevier in Solar Energy
- Vol. 252, 403-412
Emissivity measurements of W/TiAlN/TiAlSiN/TiAlSiON/TiAlSiO -based multilayer spectrally selective absorbers at high temperature
- 17 February 2023
- Published by Elsevier in Solar Energy
- Vol. 252, 403-412
Emissivity measurements of W/TiAlN/TiAlSiN/TiAlSiON/TiAlSiO -based multilayer spectrally selective absorbers at high temperature
- 21 January 2023
- Published by Springer Nature in Applied Physics A
- Vol. 129 (2) , 1-14
Effects of annealing conditions on temperature coefficient of resistance of Pt/AlOx thin-film thermistors
- 21 January 2023
- Published by Springer Nature in Applied Physics A
- Vol. 129 (2) , 1-14
Effects of annealing conditions on temperature coefficient of resistance of Pt/AlOx thin-film thermistors
- 1 January 2023
- Published by Optica Publishing Group
- p. SM2H.3
Enhancement of Optical Absorption by Oxygen Plasma Treatment in Carbon Nanotube-based Black Paint Coating
The effect of oxygen (O2) plasma treatment on the reflectance properties and surface morphology of carbon nanotube-based paint was investigated. We demonstrate a hemispherical reflectance of less than 2.5% throughout the UV-Vis-NIR range.
- 1 January 2023
- Published by Optica Publishing Group
- p. SM2H.3
Enhancement of Optical Absorption by Oxygen Plasma Treatment in Carbon Nanotube-based Black Paint Coating
The effect of oxygen (O2) plasma treatment on the reflectance properties and surface morphology of carbon nanotube-based paint was investigated. We demonstrate a hemispherical reflectance of less than 2.5% throughout the UV-Vis-NIR range.
- 19 January 2022
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 19 (2) , 403-438
A review on physical vapor deposition-based metallic coatings on steel as an alternative to conventional galvanized coatings
- 19 January 2022
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 19 (2) , 403-438
A review on physical vapor deposition-based metallic coatings on steel as an alternative to conventional galvanized coatings