Jelena Vukašinović
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jelena Vukašinović has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Goran Branković
University of Belgrade, Institute for Multidisciplinary Research, Kneza Višeslava 1a, 11030, Belgrade, Serbia
2 shared publicationsMilica Počuča-Nešić
University of Belgrade, Institute for Multidisciplinary Research, Kneza Višeslava 1a, 11030, Belgrade, Serbia
2 shared publications- Slavica M. Savic
Institute for Multidisciplinary Research-University of Belgrade, Kneza Viseslava 1a, 11030 Belgrade (Serbia)
2 shared publications - Vesna Ribić
Jozef Stefan Institute
2 shared publications Zorica Branković
University of Belgrade, Institute for Multidisciplinary Research, Kneza Višeslava 1a, 11030, Belgrade, Serbia
2 shared publications- Aden Hodzic
Research Center Pharmaceutical Engineering GmbH, 8010 Graz, Austria
1 shared publication
Latest Publications
- Open Access
KIT-5-Assisted Synthesis of Mesoporous SnO2 for High-Performance Humidity Sensors with a Swift Response/Recovery Speed
Developing highly efficient semiconductor metal oxide (SMOX) sensors capable of accurate and fast responses to environmental humidity is still a challenging task. In addition to a not so pronounced sensitivity to relative humidity change, most of the SMOXs cannot meet the criteria of real-time humidity sensing due to their long response/recovery time. The way to tackle this problem is to control adsorption/desorption processes, i.e., water-vapor molecular dynamics, over the sensor’s active layer through the powder and pore morphology design. With this in mind, a KIT-5-mediated synthesis was used to achieve mesoporous tin (IV) oxide replica (SnO2-R) with controlled pore size and ordering through template inversion and compared with a sol-gel synthesized powder (SnO2-SG). Unlike SnO2-SG, SnO2-R possessed a high specific surface area and quite an open pore structure, similar to the KIT-5, as observed by TEM, BET and SWAXS analyses. According to TEM, SnO2-R consisted of fine-grained globular particles and some percent of exaggerated, grown twinned crystals. The distinctive morphology of the SnO2-R-based sensor, with its specific pore structure and an increased number of oxygen-related defects associated with the powder preparation process and detected at the sensor surface by XPS analysis, contributed to excellent humidity sensing performances at room temperature, comprised of a low hysteresis error (3.7%), sensitivity of 406.8 kΩ/RH% and swift response/recovery speed (4 s/6 s).
Open AccessKIT-5-Assisted Synthesis of Mesoporous SnO2 for High-Performance Humidity Sensors with a Swift Response/Recovery Speed
Developing highly efficient semiconductor metal oxide (SMOX) sensors capable of accurate and fast responses to environmental humidity is still a challenging task. In addition to a not so pronounced sensitivity to relative humidity change, most of the SMOXs cannot meet the criteria of real-time humidity sensing due to their long response/recovery time. The way to tackle this problem is to control adsorption/desorption processes, i.e., water-vapor molecular dynamics, over the sensor’s active layer through the powder and pore morphology design. With this in mind, a KIT-5-mediated synthesis was used to achieve mesoporous tin (IV) oxide replica (SnO2-R) with controlled pore size and ordering through template inversion and compared with a sol-gel synthesized powder (SnO2-SG). Unlike SnO2-SG, SnO2-R possessed a high specific surface area and quite an open pore structure, similar to the KIT-5, as observed by TEM, BET and SWAXS analyses. According to TEM, SnO2-R consisted of fine-grained globular particles and some percent of exaggerated, grown twinned crystals. The distinctive morphology of the SnO2-R-based sensor, with its specific pore structure and an increased number of oxygen-related defects associated with the powder preparation process and detected at the sensor surface by XPS analysis, contributed to excellent humidity sensing performances at room temperature, comprised of a low hysteresis error (3.7%), sensitivity of 406.8 kΩ/RH% and swift response/recovery speed (4 s/6 s).
- Open Access
- 1 January 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (1) , 015901
The crucial role of defect structure in understanding the electrical properties of spark plasma sintered antimony doped barium stannate
The influence of structural defects in spark plasma sintered BaSn1-xSbxO3 (BSSO, x = 0.00 and 0.08) ceramic samples on their electrical properties was investigated in the temperature range of 300–4 K. X-ray photoelectron spectroscopy (XPS) revealed the presence of point defects, primarily oxygen vacancies (VO) and mixed oxidation states of tin (Sn2+/Sn4+) in both samples. As a result, the undoped BSSO sample exibited a non-standard semiconductor behavior, retaining its temperature-dependent resistivity. The electrical resistivity of the doped samples was two orders of magnitude lower than that of the undoped sample. The presence of structural defects such as VO, mixed oxidation states of the constituent elements, and significant amounts of O− species make the electrical resistivity of the doped sample constant in the temperature range of 300–70 K, indicating heavily-doped semiconductor behavior.
- 1 January 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (1) , 015901
Open AccessThe crucial role of defect structure in understanding the electrical properties of spark plasma sintered antimony doped barium stannate
The influence of structural defects in spark plasma sintered BaSn1-xSbxO3 (BSSO, x = 0.00 and 0.08) ceramic samples on their electrical properties was investigated in the temperature range of 300–4 K. X-ray photoelectron spectroscopy (XPS) revealed the presence of point defects, primarily oxygen vacancies (VO) and mixed oxidation states of tin (Sn2+/Sn4+) in both samples. As a result, the undoped BSSO sample exibited a non-standard semiconductor behavior, retaining its temperature-dependent resistivity. The electrical resistivity of the doped samples was two orders of magnitude lower than that of the undoped sample. The presence of structural defects such as VO, mixed oxidation states of the constituent elements, and significant amounts of O− species make the electrical resistivity of the doped sample constant in the temperature range of 300–70 K, indicating heavily-doped semiconductor behavior.
- 1 December 2020
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 40 (15) , 5566-5575
The structural, electrical and optical properties of spark plasma sintered BaSn1-Sb O3 ceramics
- 1 December 2020
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 40 (15) , 5566-5575
The structural, electrical and optical properties of spark plasma sintered BaSn1-Sb O3 ceramics