Dmytro Ivanchenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dmytro Ivanchenko has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Mykhail Yamshinskij
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” (Kyiv, Ukraine)
9 shared publications - I. V. Lukianenko
National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute
6 shared publications - Andrey Andreev
Zaporizhzhia National University
4 shared publications - Vadym Volokh
Kharkiv National Automobile and Highway University
4 shared publications - Dmytro Zhuravel
Таврійський державний агротехнологічний університет імені Дмитра Моторного
3 shared publications - Victor Rebenko
National University of Life and Environmental Sciences of Ukraine
3 shared publications
Latest Publications
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 3-17
ВПЛИВ ЦИРКОНІЮ НА ОСОБЛИВОСТІ МІКРОСТРУКТУРИ ЛИВАРНИХ АЛЮМІНІЄВИХ СПЛАВІВ
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 3-17
ВПЛИВ ЦИРКОНІЮ НА ОСОБЛИВОСТІ МІКРОСТРУКТУРИ ЛИВАРНИХ АЛЮМІНІЄВИХ СПЛАВІВ
- Open Access
Analytical Study of Temperature Fields in Aluminum Alloy Castings During Solidification in Sand and Metal Molds
The article presents the calculation of temperature fields for a casting (a cylinder 20 mm in diameter) made of Al–5%wt.Cu alloy, poured into sand (sand–clay) and metal (steel) molds at a temperature of 1123 K (with a metal mold temperature of 523 K). Many existing analytical approaches do not explicitly account for key features such as the time-dependent temperature evolution at the casting surface and center, as well as the variable temperature gradient within the casting. In this paper, the parameters calculated for the sand mold include the surface temperature change over time, as do the dynamics of the solidification front progression, and ultimately, the overall thermal field of the casting. For the metal mold, the process first determines the change in the center temperature over time, followed by the surface temperature dynamics, and finally, the complete thermal field of the casting. Particular attention is paid to determining the position of the mushy zone, namely the zero fluidity and feeding temperatures (the point at which the liquid phase loses mobility upon cooling). These temperatures are critical for casting structure formation and the initiation of shrinkage defects. To perform the calculations, the authors developed original mathematical models and provided solutions to the resulting differential equations. The study demonstrates the differences between the thermal fields in sand and metal molds: the maximum temperature difference is 195 K in the sand mold, compared to 90 K in the metal mold. Therefore, the solidification conditions for this casting in the metal mold are more favorable. The metal mold provides more favorable thermal conditions and a lower analytically predicted tendency toward shrinkage defects, but it does not guarantee their complete absence.
Open AccessAnalytical Study of Temperature Fields in Aluminum Alloy Castings During Solidification in Sand and Metal Molds
The article presents the calculation of temperature fields for a casting (a cylinder 20 mm in diameter) made of Al–5%wt.Cu alloy, poured into sand (sand–clay) and metal (steel) molds at a temperature of 1123 K (with a metal mold temperature of 523 K). Many existing analytical approaches do not explicitly account for key features such as the time-dependent temperature evolution at the casting surface and center, as well as the variable temperature gradient within the casting. In this paper, the parameters calculated for the sand mold include the surface temperature change over time, as do the dynamics of the solidification front progression, and ultimately, the overall thermal field of the casting. For the metal mold, the process first determines the change in the center temperature over time, followed by the surface temperature dynamics, and finally, the complete thermal field of the casting. Particular attention is paid to determining the position of the mushy zone, namely the zero fluidity and feeding temperatures (the point at which the liquid phase loses mobility upon cooling). These temperatures are critical for casting structure formation and the initiation of shrinkage defects. To perform the calculations, the authors developed original mathematical models and provided solutions to the resulting differential equations. The study demonstrates the differences between the thermal fields in sand and metal molds: the maximum temperature difference is 195 K in the sand mold, compared to 90 K in the metal mold. Therefore, the solidification conditions for this casting in the metal mold are more favorable. The metal mold provides more favorable thermal conditions and a lower analytically predicted tendency toward shrinkage defects, but it does not guarantee their complete absence.
- 1 December 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 162 (4) , 32-43
CHANGE IN THE STRUCTURE AND MECHANICAL PROPERTIES OF THE AM5 CASTING ALLOY STRENGTHENED WITH Zr
- 1 December 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 162 (4) , 32-43
CHANGE IN THE STRUCTURE AND MECHANICAL PROPERTIES OF THE AM5 CASTING ALLOY STRENGTHENED WITH Zr
- Open Access
- 27 August 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (12 (136)) , 6-11
Establishing patterns of structural-phase transformations when processing technogenic waste of high-speed steels by carbon thermal reduction
The object of this study is structural and phase transformations during the reduction of high-speed steel scale with carbon to obtain a resource-saving alloying additive. The task addressed is the loss of high-value elements when obtaining and using alloying material from man-made raw materials. Solving the problem is associated with determining technological indicators to enable the reduction of losses of the corresponding elements. It has been determined that the phase composition of the scale had the manifestation of FeO, Fe2O3, Fe3O4, FeWO4, MoO2, FeW3C, W2C and Mo2C. In the reduction products, a solid solution of alloying elements and carbon in α-Fe, residual oxides Fe2O3, Fe3O4 and carbides FeW3C, WC, Mo2C, Cr7C3, Cr3C2, Cr23C6, VC was found. The disordered structure of the scale with particles of irregular shape after reduction was characterized by the presence of formations of polyhedral and rounded shapes with different contents of alloying elements. Residual oxygen was within 5.78–7.14% by weight. It was established that achieving a reduction degree of 79% is sufficient since the residual carbon in carbides provides an increased reducing ability during the further reduction of the oxide component in the liquid metal during alloying. The porous structure causes faster dissolution compared to standard ferroalloys, which reduces the resources consumed by reducing the melting time. No phases with an increased tendency to sublimation were found in the obtained alloying additive. That is, there is no need to create additional conditions that prevent the loss of alloying elements during evaporation with the gas phase, which ensures an increase in the degree of extraction of the corresponding elements. The properties of the obtained alloying additive allow it to be used in smelting in an electric arc furnace as a replacement for part of standard ferroalloys
- 27 August 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (12 (136)) , 6-11
Open AccessEstablishing patterns of structural-phase transformations when processing technogenic waste of high-speed steels by carbon thermal reduction
The object of this study is structural and phase transformations during the reduction of high-speed steel scale with carbon to obtain a resource-saving alloying additive. The task addressed is the loss of high-value elements when obtaining and using alloying material from man-made raw materials. Solving the problem is associated with determining technological indicators to enable the reduction of losses of the corresponding elements. It has been determined that the phase composition of the scale had the manifestation of FeO, Fe2O3, Fe3O4, FeWO4, MoO2, FeW3C, W2C and Mo2C. In the reduction products, a solid solution of alloying elements and carbon in α-Fe, residual oxides Fe2O3, Fe3O4 and carbides FeW3C, WC, Mo2C, Cr7C3, Cr3C2, Cr23C6, VC was found. The disordered structure of the scale with particles of irregular shape after reduction was characterized by the presence of formations of polyhedral and rounded shapes with different contents of alloying elements. Residual oxygen was within 5.78–7.14% by weight. It was established that achieving a reduction degree of 79% is sufficient since the residual carbon in carbides provides an increased reducing ability during the further reduction of the oxide component in the liquid metal during alloying. The porous structure causes faster dissolution compared to standard ferroalloys, which reduces the resources consumed by reducing the melting time. No phases with an increased tendency to sublimation were found in the obtained alloying additive. That is, there is no need to create additional conditions that prevent the loss of alloying elements during evaporation with the gas phase, which ensures an increase in the degree of extraction of the corresponding elements. The properties of the obtained alloying additive allow it to be used in smelting in an electric arc furnace as a replacement for part of standard ferroalloys
- Open Access
- 30 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (131)) , 25-30
Identifying patterns in the structural-phase transformations when processing oxide doped waste with the use of carbon reducer
The object of this study is the structural and phase transformations during the carbon reduction of tungsten high-speed steel slag in order to obtain a resource-saving alloying additive. The problem is the loss of precious elements when obtaining and using alloying material from man-made raw materials. Solving the problem is related to the definition of technological parameters to enable the reduction of losses of the corresponding elements. As a result of increasing the degree of scale reduction from 33 % to 72 % and 85 %, the strengthening of the manifestation of the solid solution of carbon and alloying elements in α-Fe relative to FeWO4, FeO and Fe3O4 was revealed. Fe3C, WC, W2C, FeW3C, Fe3W3C, Fe6W6C, VC, V2C, Cr3C2, Cr7C3 and Cr23C6 also appeared. Along with this, rounded and multifaceted particles with different chemical composition and the formation of a spongy microstructure were found. It was established that the most acceptable degree of recovery is 85 %. But achieving a recovery rate of 72 % is also sufficient. This is explained by the fact that the residual carbon in the carbides provides an increased reducing capacity, which is realized during the further reduction of oxides in the liquid metal during alloying. The spongy microstructure results in faster dissolution in contrast to standard ferroalloys, which provides a reduction in melting time while reducing spent resources. No phases with an increased tendency to sublimation were found in the obtained alloying material. That is, no additional conditions are needed that restrain the loss of alloying elements during evaporation with a gaseous phase, which provides an increase in the degree of extraction of the corresponding elements. The properties of the resulting alloying material make it possible to use it in metallurgical production when smelting alloyed steel grades in an electric arc furnace, the composition of which does not have strict restrictions on the carbon content
- 30 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (131)) , 25-30
Open AccessIdentifying patterns in the structural-phase transformations when processing oxide doped waste with the use of carbon reducer
The object of this study is the structural and phase transformations during the carbon reduction of tungsten high-speed steel slag in order to obtain a resource-saving alloying additive. The problem is the loss of precious elements when obtaining and using alloying material from man-made raw materials. Solving the problem is related to the definition of technological parameters to enable the reduction of losses of the corresponding elements. As a result of increasing the degree of scale reduction from 33 % to 72 % and 85 %, the strengthening of the manifestation of the solid solution of carbon and alloying elements in α-Fe relative to FeWO4, FeO and Fe3O4 was revealed. Fe3C, WC, W2C, FeW3C, Fe3W3C, Fe6W6C, VC, V2C, Cr3C2, Cr7C3 and Cr23C6 also appeared. Along with this, rounded and multifaceted particles with different chemical composition and the formation of a spongy microstructure were found. It was established that the most acceptable degree of recovery is 85 %. But achieving a recovery rate of 72 % is also sufficient. This is explained by the fact that the residual carbon in the carbides provides an increased reducing capacity, which is realized during the further reduction of oxides in the liquid metal during alloying. The spongy microstructure results in faster dissolution in contrast to standard ferroalloys, which provides a reduction in melting time while reducing spent resources. No phases with an increased tendency to sublimation were found in the obtained alloying material. That is, no additional conditions are needed that restrain the loss of alloying elements during evaporation with a gaseous phase, which provides an increase in the degree of extraction of the corresponding elements. The properties of the resulting alloying material make it possible to use it in metallurgical production when smelting alloyed steel grades in an electric arc furnace, the composition of which does not have strict restrictions on the carbon content
- Open Access
- 5 June 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 156 (2) , 3-10
ZIRCONIUM TETRAFLUORIDE AS A HARDENER FOR ALUMINUM AND ALUMINUM-BASED ALLOYS
The paper substantiates that the use of zirconium compounds, namely zirconium dioxide and zirconium tetrafluoride, for the introduction of zirconium into aluminum is relevant, as it allows saturating aluminum-based alloys with zirconium from its intermediate products, namely ZrF4 or ZrO2. The article points out the disadvantages of saturating aluminum with zirconium from the ligature. The use of ZrF4 or ZrO2 as zirconium donors eliminates the need to obtain technically pure zirconium and ligatures from it. The results of thermodynamic calculations of the reduction of zirconium from zirconium tetrafluoride by aluminum are presented. It is established that the reduction of zirconium to Al3Zr is thermodynamically more likely. A flux composition containing zirconium tetrafluoride as a zirconium donor was developed for saturation of aluminum and alloys based on it with zirconium. The composition of the flux was selected based on the analysis of the ZrF4 - LiF state diagram, where the ratio of components was to ensure the lowest possible melting point of the mixture to increase its reactivity. The mechanism of zirconium reduction from tetrafluoride was established, according to which the presence of ternary compounds, in particular Li2ZrF6 or Li3ZrF7, which interact with aluminum, is mandatory in the flux, resulting in the formation of particles of the intermetallic compound Al3Zr. It was found that the zirconium content in the fluxes decreased from 96 % to 34 % 15 minutes after application to the metal surface. The recovered zirconium was transferred to the aluminum solution. The amount of zirconium tetrafluoride that should be introduced into aluminum or alloys based on it to ensure its typical content in the alloys, which, according to DSTU, is 0.2 % for AMg6l, AMg6lch, AMg10, and AMg10ch grades, was calculated. The change in the macrostructure of A7 aluminum after the introduction of zirconium from its tetrafluoride in the flux was studied. The saturation of A7 aluminum with zirconium from the flux grinds the zirconium solution in aluminum and forms a non-dendrite structure. У роботі обґрунтовано твердження про те, що використання сполук цирконію, а саме діоксиду й тетрафториду цирконію, для введення цирконію в алюміній є актуальним, оскільки дозволяє насичувати сплави на основі алюмінію цирконієм із проміжних продуктів його отримання, а саме з ZrF4 або ZrO2. Указано на недоліки насичення цирконієм алюмінію з лігатури. Використання ZrF4 або ZrO2 як донорів цирконію дозволяє позбутися необхідності отримання технічно чистого цирконію та лігатур із нього. Представлено результати термодинамічних розрахунків відновлення цирконію з тетрафториду цирконію алюмінієм. Встановлено, що термодинамічно більш імовірним є відновлення цирконію саме до сполуки Al3Zr. Розроблено склад флюсу, що вміщує тетрафторид цирконію як донор цирконію, призначений для насичення цирконієм алюмінію та сплавів на його основі. Склад флюсу вибирався на основі аналізу діаграми стану ZrF4 – LiF, де співвідношення компонентів мало забезпечити якомога меншу температуру плавлення суміші для підвищення її реакційної здатності. Встановлено механізм відновлення цирконію з тетрафториду, за яким у складі флюсу обов’язковою є наявність потрійних сполук, зокрема Li2ZrF6 або Li3ZrF7, які взаємодіють з алюмінієм, у результаті чого утворюються частки інтерметалідної сполуки Al3Zr. Встановлено, що вміст цирконію у флюсах через 15 хв після нанесення на поверхню металу знижувався з 96 % до 34 %. Цирконій, який відновився, переходив у алюмінієвий розчин. Розраховано кількість тетрафториду цирконію, яку потрібно вводити в алюміній або сплави на його основі з метою забезпечення типового його вмісту у сплавах, який, згідно з ДСТУ, складає 0,2 % для марок АМг6л, АМг6лч, АМг10, АМг10ч. Досліджено зміну макроструктури алюмінію марки А7 після введення цирконію з його тетрафториду у складі флюсу. Насичення алюмінію марки А7 цирконієм із флюсу подрібнює розчин цирконію в алюмінії та формує бездендритну структуру.
- 5 June 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 156 (2) , 3-10
Open AccessZIRCONIUM TETRAFLUORIDE AS A HARDENER FOR ALUMINUM AND ALUMINUM-BASED ALLOYS
The paper substantiates that the use of zirconium compounds, namely zirconium dioxide and zirconium tetrafluoride, for the introduction of zirconium into aluminum is relevant, as it allows saturating aluminum-based alloys with zirconium from its intermediate products, namely ZrF4 or ZrO2. The article points out the disadvantages of saturating aluminum with zirconium from the ligature. The use of ZrF4 or ZrO2 as zirconium donors eliminates the need to obtain technically pure zirconium and ligatures from it. The results of thermodynamic calculations of the reduction of zirconium from zirconium tetrafluoride by aluminum are presented. It is established that the reduction of zirconium to Al3Zr is thermodynamically more likely. A flux composition containing zirconium tetrafluoride as a zirconium donor was developed for saturation of aluminum and alloys based on it with zirconium. The composition of the flux was selected based on the analysis of the ZrF4 - LiF state diagram, where the ratio of components was to ensure the lowest possible melting point of the mixture to increase its reactivity. The mechanism of zirconium reduction from tetrafluoride was established, according to which the presence of ternary compounds, in particular Li2ZrF6 or Li3ZrF7, which interact with aluminum, is mandatory in the flux, resulting in the formation of particles of the intermetallic compound Al3Zr. It was found that the zirconium content in the fluxes decreased from 96 % to 34 % 15 minutes after application to the metal surface. The recovered zirconium was transferred to the aluminum solution. The amount of zirconium tetrafluoride that should be introduced into aluminum or alloys based on it to ensure its typical content in the alloys, which, according to DSTU, is 0.2 % for AMg6l, AMg6lch, AMg10, and AMg10ch grades, was calculated. The change in the macrostructure of A7 aluminum after the introduction of zirconium from its tetrafluoride in the flux was studied. The saturation of A7 aluminum with zirconium from the flux grinds the zirconium solution in aluminum and forms a non-dendrite structure. У роботі обґрунтовано твердження про те, що використання сполук цирконію, а саме діоксиду й тетрафториду цирконію, для введення цирконію в алюміній є актуальним, оскільки дозволяє насичувати сплави на основі алюмінію цирконієм із проміжних продуктів його отримання, а саме з ZrF4 або ZrO2. Указано на недоліки насичення цирконієм алюмінію з лігатури. Використання ZrF4 або ZrO2 як донорів цирконію дозволяє позбутися необхідності отримання технічно чистого цирконію та лігатур із нього. Представлено результати термодинамічних розрахунків відновлення цирконію з тетрафториду цирконію алюмінієм. Встановлено, що термодинамічно більш імовірним є відновлення цирконію саме до сполуки Al3Zr. Розроблено склад флюсу, що вміщує тетрафторид цирконію як донор цирконію, призначений для насичення цирконієм алюмінію та сплавів на його основі. Склад флюсу вибирався на основі аналізу діаграми стану ZrF4 – LiF, де співвідношення компонентів мало забезпечити якомога меншу температуру плавлення суміші для підвищення її реакційної здатності. Встановлено механізм відновлення цирконію з тетрафториду, за яким у складі флюсу обов’язковою є наявність потрійних сполук, зокрема Li2ZrF6 або Li3ZrF7, які взаємодіють з алюмінієм, у результаті чого утворюються частки інтерметалідної сполуки Al3Zr. Встановлено, що вміст цирконію у флюсах через 15 хв після нанесення на поверхню металу знижувався з 96 % до 34 %. Цирконій, який відновився, переходив у алюмінієвий розчин. Розраховано кількість тетрафториду цирконію, яку потрібно вводити в алюміній або сплави на його основі з метою забезпечення типового його вмісту у сплавах, який, згідно з ДСТУ, складає 0,2 % для марок АМг6л, АМг6лч, АМг10, АМг10ч. Досліджено зміну макроструктури алюмінію марки А7 після введення цирконію з його тетрафториду у складі флюсу. Насичення алюмінію марки А7 цирконієм із флюсу подрібнює розчин цирконію в алюмінії та формує бездендритну структуру.
- Open Access
- 31 October 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (125)) , 17-22
Identifying the features of structural and phase transformations during the processing of oxide waste from the production of high-speed steel
Peculiarities of phase and structural transformations during the carbon-thermal recovery of high-speed steel slag with the production of an alloying additive were investigated. This is necessary to determine the technological indicators that allow reducing the loss of high-value elements during the production and use of the alloying additive. A gradual change in the degree of scale reduction from 32 % to 69 % and 77 % led to an increase in the appearance of the solid solution of alloying elements and carbon in the α-Fe lattice with respect to FeWO4 and Fe3O4. Along with this, Fe3C, FeW3C, WC, VC, V2C, and Cr3C2 were manifested. At the same time, the formation of polyhedral and rounded particles of different chemical composition and the formation of a spongy microstructure was observed. It was determined that the most acceptable degree of recovery is 77 %. At the same time, the degree of reduction of 69 % is also sufficient since due to the residual carbon in the form of carbides, an increased reduction capacity is ensured with additional reduction of the oxide component in the liquid metal during alloying. The spongy microstructure provides relatively fast dissolution compared to standard ferroalloys, which causes a reduction in the total melting time while reducing the resources spent. No phases and compounds characterized by an increased tendency to sublimation were detected in the obtained alloying additive. That is, there is no need to provide additional conditions that prevent the loss of high-value elements during evaporation with the gas phase, which causes an increase in the degree of extraction of alloying elements. The indicators of the obtained alloying additive make it possible to melt alloyed steel in an electric arc furnace with respect to brands whose composition does not have strict restrictions on carbon, while replacing a part of standard ferroalloys.
- 31 October 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (125)) , 17-22
Open AccessIdentifying the features of structural and phase transformations during the processing of oxide waste from the production of high-speed steel
Peculiarities of phase and structural transformations during the carbon-thermal recovery of high-speed steel slag with the production of an alloying additive were investigated. This is necessary to determine the technological indicators that allow reducing the loss of high-value elements during the production and use of the alloying additive. A gradual change in the degree of scale reduction from 32 % to 69 % and 77 % led to an increase in the appearance of the solid solution of alloying elements and carbon in the α-Fe lattice with respect to FeWO4 and Fe3O4. Along with this, Fe3C, FeW3C, WC, VC, V2C, and Cr3C2 were manifested. At the same time, the formation of polyhedral and rounded particles of different chemical composition and the formation of a spongy microstructure was observed. It was determined that the most acceptable degree of recovery is 77 %. At the same time, the degree of reduction of 69 % is also sufficient since due to the residual carbon in the form of carbides, an increased reduction capacity is ensured with additional reduction of the oxide component in the liquid metal during alloying. The spongy microstructure provides relatively fast dissolution compared to standard ferroalloys, which causes a reduction in the total melting time while reducing the resources spent. No phases and compounds characterized by an increased tendency to sublimation were detected in the obtained alloying additive. That is, there is no need to provide additional conditions that prevent the loss of high-value elements during evaporation with the gas phase, which causes an increase in the degree of extraction of alloying elements. The indicators of the obtained alloying additive make it possible to melt alloyed steel in an electric arc furnace with respect to brands whose composition does not have strict restrictions on carbon, while replacing a part of standard ferroalloys.
- 1 June 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 152 (2) , 16-23
TECHNOLOGICAL FEATURES OF MANUFACTURING ALLOY AK7h STRENGTHENED WITH ZIRCONIUM INTRODUCED WITH ZIRCONIUM TETRAFLUORIDE
The paper considers the important features of the technology of strengthening AK7ch aluminum alloy with zirconium introduced with its tetrafluoride. The choice of a complex flux containing zirconium tetrafluoride in its composition is justified. It is indicated that in order to recover zirconium from its tetrafluoride in the aluminum melt, it is first of all necessary to ensure the formation of sodium or potassium fluorozirconate in the strengthening mixture. The mechanism of recovery of zirconium from tetrafluoride is presented. Technological recommendations for obtaining AK7ch alloy are given. It has been established that the complex flux intended to the alloy, which is modified, must be injected into liquid aluminum before the introduction of other alloying elements, namely silicon and magnesium. The maximum appropriate temperature for injecting zirconium into the aluminum melt from the complex flux is indicated. The maximum amount of zirconium that was recovered is 0.4%. The microstructure and mechanical properties of an alloy strengthened by zirconium from its tetrafluoride, which was injected into the alloy in the amount from 0.8 to 1.2%, were studied. As a result of the modification of aluminum alloy AK7ch with zirconium, the grains of silicon solution in aluminum (α-phase) are grind. No other structural changes are observed. The value of tensile strength and relative elongation of the alloy increases by 1.3 and 1.7 times, respectively.
- 1 June 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 152 (2) , 16-23
TECHNOLOGICAL FEATURES OF MANUFACTURING ALLOY AK7h STRENGTHENED WITH ZIRCONIUM INTRODUCED WITH ZIRCONIUM TETRAFLUORIDE
The paper considers the important features of the technology of strengthening AK7ch aluminum alloy with zirconium introduced with its tetrafluoride. The choice of a complex flux containing zirconium tetrafluoride in its composition is justified. It is indicated that in order to recover zirconium from its tetrafluoride in the aluminum melt, it is first of all necessary to ensure the formation of sodium or potassium fluorozirconate in the strengthening mixture. The mechanism of recovery of zirconium from tetrafluoride is presented. Technological recommendations for obtaining AK7ch alloy are given. It has been established that the complex flux intended to the alloy, which is modified, must be injected into liquid aluminum before the introduction of other alloying elements, namely silicon and magnesium. The maximum appropriate temperature for injecting zirconium into the aluminum melt from the complex flux is indicated. The maximum amount of zirconium that was recovered is 0.4%. The microstructure and mechanical properties of an alloy strengthened by zirconium from its tetrafluoride, which was injected into the alloy in the amount from 0.8 to 1.2%, were studied. As a result of the modification of aluminum alloy AK7ch with zirconium, the grains of silicon solution in aluminum (α-phase) are grind. No other structural changes are observed. The value of tensile strength and relative elongation of the alloy increases by 1.3 and 1.7 times, respectively.
- Open Access
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (12 (120)) , 46-51
Identifying features in the structural and phase composition of the products of recycling of the scale of high-speed cutting steel by carbon thermal reduction
This paper reports a study into the features of the structural-phase composition of products from the carbon-thermal reduction of scale of high-speed steels that yields an alloying additive. This is necessary to determine the technological parameters that reduce the loss of target elements in the process of obtaining and using resource-saving alloying material. The study indicates that when the degree of scale reduction changed from 28 % to 67 % and 81 %, an increase in the manifestation of a solid solution of carbon and alloying elements in the α-Fe lattice was observed. At the same time, the intensity of the diffraction maxima of FeO and Fe3O4 decreased. In the reduced products, the presence of Fe3C, FeW3C, Fe3W3C, and WC was traced. With an increase in the degree of scale reduction from 28 % to 67 %, the disordered (of "loose" appearance) microstructure was replaced with the formed particles of round and multifaceted shape with different content of alloying elements. At the reduction stage of 81 %, the microstructure had a finely fibrous structure. Based on the suite of studies, the most acceptable degree of reduction of scale of high-speed steel, followed by the use of the obtained material as an alloying additive, is 81 %. At the same time, ensuring the degree of recovery at the level of 67 % would also suffice. This is due to the fact that residual carbon in the form of carbides provides an increased reducing ability and degree of assimilation of alloying elements with the restoration of the residual oxide component in the liquid metal during doping. Spongy microstructure contributes to faster dissolution, in relation to the corresponding standard ferroalloys. This ensures a reduction in the total smelting time and, as a result, a decrease in the energy consumed
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (12 (120)) , 46-51
Open AccessIdentifying features in the structural and phase composition of the products of recycling of the scale of high-speed cutting steel by carbon thermal reduction
This paper reports a study into the features of the structural-phase composition of products from the carbon-thermal reduction of scale of high-speed steels that yields an alloying additive. This is necessary to determine the technological parameters that reduce the loss of target elements in the process of obtaining and using resource-saving alloying material. The study indicates that when the degree of scale reduction changed from 28 % to 67 % and 81 %, an increase in the manifestation of a solid solution of carbon and alloying elements in the α-Fe lattice was observed. At the same time, the intensity of the diffraction maxima of FeO and Fe3O4 decreased. In the reduced products, the presence of Fe3C, FeW3C, Fe3W3C, and WC was traced. With an increase in the degree of scale reduction from 28 % to 67 %, the disordered (of "loose" appearance) microstructure was replaced with the formed particles of round and multifaceted shape with different content of alloying elements. At the reduction stage of 81 %, the microstructure had a finely fibrous structure. Based on the suite of studies, the most acceptable degree of reduction of scale of high-speed steel, followed by the use of the obtained material as an alloying additive, is 81 %. At the same time, ensuring the degree of recovery at the level of 67 % would also suffice. This is due to the fact that residual carbon in the form of carbides provides an increased reducing ability and degree of assimilation of alloying elements with the restoration of the residual oxide component in the liquid metal during doping. Spongy microstructure contributes to faster dissolution, in relation to the corresponding standard ferroalloys. This ensures a reduction in the total smelting time and, as a result, a decrease in the energy consumed