WZWei Zou

Wei Zou

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Wei Zou has a total of 42 co-authors. Here are the top co-authors by number of shared publications:

  • Hu Yang

    School of Chemical Engineering, Sichuan University of Science & Engineering, Zigong643000, China

    2 shared publications
  • Hui Li

    Research and Development Center, Zhonghao Chenguang Chemical Research Institute, Zigong 643000, P. R. China

    2 shared publications
  • Jie Yan

    School of Chemical Engineering, Sichuan University of Science & Engineering, Zigong643000, China

    2 shared publications
  • Bo Liu

    Zhonghao Chenguang Chemical Research Institute of Chemical Industry Co., Ltd., Zigong 643201, P R China

    1 shared publication
  • Chen Qian

    School of Materials Science and Engineering Zhejiang Sci‐Tech University Hangzhou China

    1 shared publication
  • Deli Tang

    Southwestern Institute of Physics, Chengdu 610207, China

    1 shared publication

Latest Publications

  • Open Access

    Low-Temperature Plasma-Assisted Metallization of PTFE: A Focused Review

    by Meiyan Chen, Jinru Ou, Yue Zhang, Xuan Liu, Ke Yao, Xueping Geng, Deli Tang, Wei Zou, Fanya Jin, Jun Zhou

    Polytetrafluoroethylene (PTFE) is an important dielectric and structural substrate for high-frequency, flexible, low-background, and other electronic systems because of its low dielectric loss, high electrical resistivity, low moisture absorption, chemical inertness, and thermal stability. However, its fluorine-rich surface, low surface energy, and weak boundary layer hinder metal nucleation and interfacial bonding, frequently leading to discontinuous film growth, high interfacial resistance, and premature delamination. This focused review summarizes recent progress in low-temperature plasma-assisted metallization of PTFE, with particular emphasis on the relationships among plasma activation, interface formation, electrical functionality, reliability, and manufacturability. The effects of plasma-induced physical etching, defluorination, radical generation, polar functionalization, weak-boundary-layer removal, and hydrophobic recovery are first discussed. Representative metallization routes are then reviewed, including direct physical vapor deposition, plasma-assisted electroless plating, plasma-induced grafting, metallic interlayers, ion implantation, and hybrid plasma-deposition processes. Particular attention is given to interface-strengthening mechanisms involving chemical bonding, mechanical interlocking, diffusion control, carbon-rich or graded transition regions, and interdiffusion. The key trade-offs among adhesion strength, conductor resistance, dielectric integrity, surface-modification stability, and mechanical or environmental reliability are further analyzed for electronic-substrate applications. Although metallic interlayers, ion implantation, and hybrid processes can provide more stable interfaces than plasma activation alone, challenges remain in controlling plasma-induced damage, surface aging, interfacial carbonization, and process reproducibility. Recent 2024–2026 studies further show that these interface technologies can translate into low-loss Cu/PTFE laminates, flexible circuits, integrated vacuum metallization stacks, and selectively patterned conductors. The relevance to low-power systems is therefore treated as one application context at the substrate/interconnect level rather than as evidence that PTFE metallization directly reduces circuit switching power.

  • Long-cycle stable operation of fluoride-ion batteries at room temperature enabled by an advanced interface engineering and ion diffusion kinetics regulation strategy

    by Jia Xiang, Meiyan Chen, Ying Lei, Jun Zhou, Wei Zou, Rongwen Lu, Shufen Zhang

    Fluoride-ion batteries (FIBs) offer a high theoretical energy density of 5000 W h L−1 and superior safety, but they face significant challenges such as electrode material dissolution and volume changes during cycling. Herein, this study presents an advanced interface engineering strategy to enhance the stability of the electrolyte–electrode interface. Through plasma treatment, substrate surface energy and adhesion are increased, while a co-deposition device generates a high-energy ion beam (Bi3+ and F−), depositing atoms densely and uniformly on CuF2 to form a protective layer. Additionally, regulating the BiOxFy crystal structure via controlled O2− ion injection optimizes F− transport and diffusion barriers. This modulation, driven by O-2p and F-2p electron density states, retards F− diffusion kinetics and mitigates volume changes in CuF2 during cycling. The resulting battery showed stable performance in N,N,N-dimethyl-N,N-dineopentylammonium fluoride liquid electrolyte at room temperature, including a specific capacity of 110 mA h g−1 and a fiftyfold longer cycling life than that of existing Cu@LaF3 core–shell batteries. Furthermore, X-ray absorption fine structure analysis reveals the pivotal role of a BiOF film in mitigating the lattice recombination effect by assimilating excess F−. These findings highlight the importance of this advanced interface strategy for advancements in FIBs.


  • Effect of slight structural difference in polyvinylidene fluoride binders on the electrochemical performance of single-crystal LiNi0.5Co0.2Mn0.3O2 cathode

    by Tangzhe Cao, Huaming Xie, Ying Lei, Wei Zou, Hui Li, Kang Yang, Tong Zan, Liming Li, Yongxian Fang

    Polyvinylidene fluoride (PVDF) binder is an important part of lithium-ion batteries, where a slight structural difference can significantly affect the capacitance and service life of batteries. Herein, ATR-FTIR technology and a rheological test were employed to investigate the crystal forms and rheological behavior of three different PVDF binders, respectively. The results showed that PVDF-CG has low molecular weight, high α/β phase ratio, strong adhesive action and stripping strength, which are closely associated with the durability and electrochemical properties of LiNi0.5Co0.2Mn0.3O2 single-crystal (denoted as SC) materials. The SCs with PVDF-CG binder exhibited a capacity retention of 93.44% after 100 cycles at a rate of 1C and high rate performance (92 mA h g−1 at 10C), which was higher than that of PVDF-HSV900 (90.31%, 86 mA h g−1 at 10C) and PVDF-Solvay 5130 (90.52%, 72 mA h g−1 at 10C). The XPS and HR-TEM analysis showed that the cycled SCs bonded with HSV900 and Solvay 5130 as binders suffered from severe interface structural degradation, while SCs with PVDF-CG maintained a well-layered structure and the formation of a surface NiO-like rock-salt phase was greatly inhibited. This work demonstrated that the capacity, rate capability and interface stability of SC cathodes are significantly affected by the mode and strength of the adhesion and stripping strength of PVDF binders, which are closely associated with α/β phase ratios, providing a useful reference for the development of efficient binders.


  • Open Access

    Preparation of High-Strength and Excellent Compatibility Fluorine/Silicone Rubber Composites under the Synergistic Effect of Fillers

    by RongPeng Zhao, ZhiGang Yin, Wei Zou, Hu Yang, Jie Yan, WenJiang Zheng, Hui Li

    Fluorine/silicone composite rubber is widely used as a sealing material in aerospace, missile, automotive, petroleum, and other industries, but the traditional process does not use synergistic fillers to strengthen the composite system. In this research, fumed SiO2 and black caron (N990) were used as synergistic fillers, fluorine/silicone composite rubber was prepared by mechanical mixing process, and three different fluorine rubber systems were used to find the best composite material. The mechanical properties, thermal properties, aging properties, moderate strength properties, and microstructure of the composites were evaluated. Studies have shown that mixing the two can produce a certain interface interaction and effectively improve the compatibility. The physical properties of the material tended to decrease during the increase in the added amount of silicone rubber (MVQ). The maximum tensile strength of the hybrid material can reach 15 MPa. The optimal mixing ratio is fluororubber/silicone rubber (FKM/MVQ) = 9/1. At this time, the mechanical properties of the composite material are in the best state, and SiO2 and black caron (N990) have a reinforcing effect, which can effectively improve the mechanical properties. After the composite was kept at 200 °C for 48 h, the tensile strength and elongation of the best sample A1 were 99.5 and 97.0%, respectively, showing excellent anti-aging properties. This work provides a method to fabricate high-strength fluorine/silicone composites using synergistic fillers that may be used in heat-medium-sealed environments.


  • Hydrogels containing modified ammonium polyphosphate for fireproof materials

    by Qian Chen, Xiao Feng Cui, Wen Jiang Zheng, Wei Zou, Yanli Li, Jie Yan, Hu Yang, Fan Yang, Hai Bo Zhang

    Hydrogels containing a large amount of water have been widely studied as fireproof materials. However, the organic networks that composed the gel easily burns as water evaporates. In this work, the widely used intumescent flame‐retardant ammonium polyphosphate was modified by carbon–carbon double bonds (abbreviated as MAPP) and introduced in alginate/poly (acrylamide‐co‐stearyl methacrylate) [alginate/P(AAm‐co‐SMA)] hydrogel by free radical polymerization. The resultant MAPP@alginate/P(AAm‐co‐SMA) hydrogels show good mechanical strength of 650 kPa and healing efficiency of 80%. Thermal analysis and thermal protective performance tests indicate that the MAPP particles improve the thermal stability and heat resistance of gel. The fireproof test shows that the MAPP@alginate/P(AAm‐co‐SMA) gel composite shows twice of fire proof time over the pure hydrogels.


  • Open Access

    Small amount of TiO 2 modified SnO 2 with enhanced photocatalytic performance toward the removal of rhodamine B

    by Yi Zhang, Hu Yang, Wei Zou

    Tin dioxide (SnO 2 ) photocatalyst has broad prospects for the degradation of toxic organic pollutants; however, its practical application is greatly hampered by poor activity due to the high recombination rates of photogenerated electron‐hole pairs. In this work, titania (TiO 2 ) modified SnO 2 photocatalysts were obtained by a facile hydrothermal method to suppress the rapid recombination of photogenerated electron‐hole pairs and improve the photocatalytic activity. Ultraviolet–visible (UV–vis)_ diffuse reflectance spectra suggest that TiO 2 –SnO 2 composite photocatalysts hold stronger UV light absorption ability than that of the pure SnO 2 . Surface photovoltage spectroscopy and photoelectrochemistry results show that the separation rate of photogenerated charge pairs of TiO 2 –SnO 2 photocatalysts was greatly enhanced. The photocatalytic activities of the photocatalysts were evaluated by the decay of rhodamine B (RhB) under UV irradiation illumination. The results display that modification of SnO 2 by TiO 2 can largely enhance the photocatalytic activity and the photocatalytic performance of 0.5:1‐TS sample is nearly 5 times that of the pure SnO 2 . Moreover, maintaining the ratio of TiO 2 and SnO 2 at 0.5:1, the amount of catalyst was 30 mg, the concentration of dye was 10 mg/l, and the pH of RhB solution was 2, the sample has the best photocatalytic activity.


  • Thermally Driven Separation of Perfluoroalkyl Substances with High Efficiency

    by Jia Xiang, Wen Jiang Zheng, Jie Yan, XiaoFeng Liang, Haibo Zhang, Bo Liu, Wei Zou

    Perfluoroalkyl substances (PFASs), such as perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS), can contaminate the surface and groundwater. Common treatment strategies and adsorbents have low adsorption efficiencies and poor selectivity towards PFASs due to the extremely low surface energy of these compounds. This paper reports the use of a phenolic resin (PR) modified with perfluoroalkyl (PFA) segments and thermally-sensitive poly(ethylene glycol) (PEG) segments (PR-PEG-PFA) to remove PFOA and PFOS from water. The modified PR microspheres captured >90% of PFASs and were insensitive to common anionic surfactants. By treating simulated wastewater six times with this material, the PFOA concentration in water was reduced from 1 ppm to 43 ppt (43 ng L-1), showing that PR-PEG-PFA is a promising adsorbent for PFASs separation, recovery, and recycling.