Tamara Ivanovna Dorofeeva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tamara Ivanovna Dorofeeva has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Marina Vladimirovna Fedorischeva
Institute of Strength Physics and Materials Science SB RAS, Tomsk, Russian Federation
6 shared publications - Viktor Petrovich Sergeev
Institute of Strength Physics and Materials Science of the Siberian Branch, Russian Academy of Sciences, Tomsk, Russian Federation
5 shared publications - Mark P. Kalashnikov
Institute of Strength Physics and Materials Science of the Siberian Branch, Russian Academy of Sciences, Tomsk, Russian Federation
4 shared publications - Tatiana A. Gubaidulina
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
3 shared publications - Ngo Thanh Binh
Southern Branch of Joint Vietnam-Russia Tropical Science and Technology Research Center, 3, 3/2 Street, Vuon Lai Ward, Ho Chi Minh City, Vietnam
2 shared publications - A. V. Voronov
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
1 shared publication
Latest Publications
- 1 May 2026
- Published by Springer Nature in Russian Physics Journal
- Vol. 69 (5) , 737-743
Effect of surface modification of structural steel on its corrosion properties
- 1 May 2026
- Published by Springer Nature in Russian Physics Journal
- Vol. 69 (5) , 737-743
Effect of surface modification of structural steel on its corrosion properties
- 8 December 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (6) , 1847-1850
Effect of Modification of the Surface of VNS-5 Steel Samples by Ion-Plasma Methods on the Fracture Pattern during Fatigue Tests
Samples of structural aviation steel VNS-5 were implanted with carbon ions using ion-beam implantation. The modified layer was about 200 nm; the carbon content did not exceed 10% in this layer. This study shows that the VNS-5 specimens implanted with carbon ions exhibit high low-cycle fatigue properties. The origin and behavior of fatigue cracks in implanted samples differs from non-implanted material and does not depend on the magnitude of the load at low-cycle fatigue. The high surface residual compressive stress in the implanted material helps to suppress the nucleation and spread of surface cracks, thereby improving the fatigue resistance of steel.
- 8 December 2025
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 16 (6) , 1847-1850
Effect of Modification of the Surface of VNS-5 Steel Samples by Ion-Plasma Methods on the Fracture Pattern during Fatigue Tests
Samples of structural aviation steel VNS-5 were implanted with carbon ions using ion-beam implantation. The modified layer was about 200 nm; the carbon content did not exceed 10% in this layer. This study shows that the VNS-5 specimens implanted with carbon ions exhibit high low-cycle fatigue properties. The origin and behavior of fatigue cracks in implanted samples differs from non-implanted material and does not depend on the magnitude of the load at low-cycle fatigue. The high surface residual compressive stress in the implanted material helps to suppress the nucleation and spread of surface cracks, thereby improving the fatigue resistance of steel.
- 1 April 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (4) , 618-624
Effect of surface modification of structural steel on its mechanical and corrosion properties
- 1 April 2025
- Published by Springer Nature in Russian Physics Journal
- Vol. 68 (4) , 618-624
Effect of surface modification of structural steel on its mechanical and corrosion properties
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Influence of corrosion damage on fatigue life of VNS-5 steel after ion-beam treatment
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Influence of corrosion damage on fatigue life of VNS-5 steel after ion-beam treatment
- Open Access
Investigation of Corrosion Properties and Composition of the Surface Formed on AISI 321 Stainless Steel by Ion Implantation
In this work, the corrosion resistance of AISI 321 stainless steel is increased through. the two-stage implantation of oxygen ions and of both aluminum and boron ions together. During ion implantation, a modified layer with a thickness of about 200 nm is formed, which affects the properties of material. The increase in corrosion resistance is confirmed by prolonged acid corrosion tests at pH 3.5 and by accelerated electrochemical tests using a potentiostat. The corrosion rate of the implanted sample is 0.708 μA/cm2, in contrast to the non-implanted sample (1.26 μA/cm2). The modified surface layer is examined using X-ray photoelectron spectroscopy (XPS), secondary-ion mass spectrometry (SIMS), and transmission electron microscopy (TEM). Aluminum and boron are implanted to a depth of more than 250 nm. It is found that the modified surface of the stainless steel substrate contains oxides of implanted ions (Al2O3) and oxides of substrate ions (Cr2O3 and NiCr2O4).
Open AccessInvestigation of Corrosion Properties and Composition of the Surface Formed on AISI 321 Stainless Steel by Ion Implantation
In this work, the corrosion resistance of AISI 321 stainless steel is increased through. the two-stage implantation of oxygen ions and of both aluminum and boron ions together. During ion implantation, a modified layer with a thickness of about 200 nm is formed, which affects the properties of material. The increase in corrosion resistance is confirmed by prolonged acid corrosion tests at pH 3.5 and by accelerated electrochemical tests using a potentiostat. The corrosion rate of the implanted sample is 0.708 μA/cm2, in contrast to the non-implanted sample (1.26 μA/cm2). The modified surface layer is examined using X-ray photoelectron spectroscopy (XPS), secondary-ion mass spectrometry (SIMS), and transmission electron microscopy (TEM). Aluminum and boron are implanted to a depth of more than 250 nm. It is found that the modified surface of the stainless steel substrate contains oxides of implanted ions (Al2O3) and oxides of substrate ions (Cr2O3 and NiCr2O4).
- Open Access
Structural-Phase Change of Multilayer Ceramics Zr-Y-O/Si-Al-N under High Temperature
To increase the thermocyclic resistance of material, multilayer coatings with alternating layers of Zr-Y-O and Si-Al-N were obtained via magnetron sputtering. It was established that a coating layer based on Zr-Y-O has a columnar structure; the height of the columns is determined by the thickness of the layer. The Si-Al-N-based layer is amorphous. There were monoclinic and tetragonal phases with a large lattice parameter in the composition of the Zr-Y-O-based coating layer. After high-temperature annealing, a tetragonal phase with a small lattice parameter appeared in the microscope column. In the “in situ” mode, a change in the structural state of the Zr-Y-O coating layer was detected in the temperature range of 450–500 °C; namely, a change in the grain size and coherent scattering regions, and an increase in internal elastic stresses. It was found that the thermocyclic resistance increased by more than two times for multilayer samples compared to the single-layer ones we studied earlier.
Open AccessStructural-Phase Change of Multilayer Ceramics Zr-Y-O/Si-Al-N under High Temperature
To increase the thermocyclic resistance of material, multilayer coatings with alternating layers of Zr-Y-O and Si-Al-N were obtained via magnetron sputtering. It was established that a coating layer based on Zr-Y-O has a columnar structure; the height of the columns is determined by the thickness of the layer. The Si-Al-N-based layer is amorphous. There were monoclinic and tetragonal phases with a large lattice parameter in the composition of the Zr-Y-O-based coating layer. After high-temperature annealing, a tetragonal phase with a small lattice parameter appeared in the microscope column. In the “in situ” mode, a change in the structural state of the Zr-Y-O coating layer was detected in the temperature range of 450–500 °C; namely, a change in the grain size and coherent scattering regions, and an increase in internal elastic stresses. It was found that the thermocyclic resistance increased by more than two times for multilayer samples compared to the single-layer ones we studied earlier.
- 1 December 2022
- Published by Springer Nature in Russian Physics Journal
- Vol. 65 (8) , 1311-1317
Structure and Phase Composition of Magnetronsputter-Deposited Corrosion Resistant Al–Si–N/Ni/Al–Si–N Coatings
- 1 December 2022
- Published by Springer Nature in Russian Physics Journal
- Vol. 65 (8) , 1311-1317
Structure and Phase Composition of Magnetronsputter-Deposited Corrosion Resistant Al–Si–N/Ni/Al–Si–N Coatings