Fei Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fei Liu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jaakko Leppäniemi
VTT Technical Research Centre of Finland Ltd
4 shared publications - Liam Gillan
VTT Technical Research Centre of Finland Ltd, Espoo, Finland
3 shared publications - Ari Alastalo
VTT Technical Research Centre of Finland Ltd, Espoo, Finland
2 shared publications Asko Sneck
VTT Technical Research Centre of Finland Ltd
1 shared publication- Asko Sneck
VTT Technical Research Centre of Finland Ltd, Espoo, Finland
1 shared publication Olli Halonen
VTT Technical Research Centre of Finland Ltd
1 shared publication
Latest Publications
- Open Access
- 3 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (23) , 34150-34160
ALD-Grown ZnO TFTs Patterned by High-Resolution Reverse-Offset Printing
Zinc oxide (ZnO) is a benign and earth-abundant semiconductor material that has been applied in thin-film transistors (TFTs) for decades and can be used in biodegradable, transient, and biocompatible devices. Printing as an alternative fabrication method to conventional TFT manufacturing methods can deliver some benefits, such as simultaneous film deposition and patterning, good scalability, low cost, and material-saving features. However, the high annealing temperature needed for ink-to-metal oxide conversion and film densification, compounded by the poor patterning resolution of conventional printing methods, still limits the use of printing in the fabrication of flexible metal oxide TFTs. Atomic layer deposition (ALD) has recently emerged as a promising fabrication method for high-performance metal oxide TFTs that can offer more conformal film growth, precise film thickness, and higher film quality at low temperatures compared to sputtering, spin coating, or printing. Although ALD-based ZnO TFTs patterned with photolithography exhibit good electrical properties, they cannot be readily scaled to a high-throughput fabrication. Very little attention has been paid so far to the combination of low-temperature ALD growth with printing to obtain more scalable manufacturing of high-performance thin-film electronics. To overcome this challenge, we propose high-resolution reverse-offset printing (ROP) of a simple polymer resist to pattern an ALD-grown ZnO film at few μm resolution to fabricate TFTs. In this work, we report high-performance ZnO TFTs that are ALD-grown at a low temperature of 150 °C and ROP-patterned with promising stability and uniformity, a high field-effect mobility (μFE) of ∼16.6 cm2 (Vs)-1, an almost zero turn-on voltage (Von) of ∼-0.49 V, a high current on-off ratio (Ion/Ioff) of >108, a low operation voltage (Vop) of ≤5 V, and a negligible hysteresis (Vhyst) of ∼0.13 V. The combination of ALD and the ROP-patterning process could be developed further to fabricate fully flexible high-resolution metal oxide TFT-based circuits in the future.
- 3 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (23) , 34150-34160
Open AccessALD-Grown ZnO TFTs Patterned by High-Resolution Reverse-Offset Printing
Zinc oxide (ZnO) is a benign and earth-abundant semiconductor material that has been applied in thin-film transistors (TFTs) for decades and can be used in biodegradable, transient, and biocompatible devices. Printing as an alternative fabrication method to conventional TFT manufacturing methods can deliver some benefits, such as simultaneous film deposition and patterning, good scalability, low cost, and material-saving features. However, the high annealing temperature needed for ink-to-metal oxide conversion and film densification, compounded by the poor patterning resolution of conventional printing methods, still limits the use of printing in the fabrication of flexible metal oxide TFTs. Atomic layer deposition (ALD) has recently emerged as a promising fabrication method for high-performance metal oxide TFTs that can offer more conformal film growth, precise film thickness, and higher film quality at low temperatures compared to sputtering, spin coating, or printing. Although ALD-based ZnO TFTs patterned with photolithography exhibit good electrical properties, they cannot be readily scaled to a high-throughput fabrication. Very little attention has been paid so far to the combination of low-temperature ALD growth with printing to obtain more scalable manufacturing of high-performance thin-film electronics. To overcome this challenge, we propose high-resolution reverse-offset printing (ROP) of a simple polymer resist to pattern an ALD-grown ZnO film at few μm resolution to fabricate TFTs. In this work, we report high-performance ZnO TFTs that are ALD-grown at a low temperature of 150 °C and ROP-patterned with promising stability and uniformity, a high field-effect mobility (μFE) of ∼16.6 cm2 (Vs)-1, an almost zero turn-on voltage (Von) of ∼-0.49 V, a high current on-off ratio (Ion/Ioff) of >108, a low operation voltage (Vop) of ≤5 V, and a negligible hysteresis (Vhyst) of ∼0.13 V. The combination of ALD and the ROP-patterning process could be developed further to fabricate fully flexible high-resolution metal oxide TFT-based circuits in the future.
- Open Access
- 1 March 2023
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 8 (1) , 015017
Oxide TFTs with S/D-contacts patterned by high-resolution reverse-offset printed resist layers
Besides the metal oxide thin film transistors (TFTs) in flat-panel displays that are fabricated using vacuum-processes, there is a growing interest in the fabrication of metal oxide TFTs by means of scalable, low-cost solution and printing processes for applications such as flexible displays and biosensors. Although devices with printed semiconductor and gate insulator can exhibit good electrical performance, source/drain-contacts (S/D) printed from silver (Ag) nanoparticles (NPs) typically suffer from deteriorated electrical characteristics and stability problems. On the other hand, metals providing good contacts, such as aluminum (Al), titanium (Ti) and molybdenum (Mo), cannot be formed as air-stable NPs. To overcome these issues, we have developed a patterning method based on high-resolution reverse-offset printing (ROP) of a sacrificial polymer resist layer. ROP delivers patterns with micrometer-level resolution and steep sidewalls, which are ideal for patterning vacuum-deposited metal contacts at high resolution via lift-off process. Solution-processed indium oxide (In2O3) TFTs were successfully fabricated by using ROP lift-off process for patterning of gate and S/D-electrodes using Al. The fabricated In2O3-based TFTs with Al S/D-contacts exhibit good uniformity, constant mobility (μ sat) ∼ 2 cm2 (V s)−1 over a wide range of width/length-ratios (W/L) and almost zero turn-on voltage (V on) ∼ −0.2 V. TFTs down to 5 µm channel lengths were successfully patterned. Further development of the fabrication process could lead to flexible fully-print-patterned high-resolution TFT backplanes for flexible displays, biosensors, photosensors and x-ray detectors.
- 1 March 2023
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 8 (1) , 015017
Open AccessOxide TFTs with S/D-contacts patterned by high-resolution reverse-offset printed resist layers
Besides the metal oxide thin film transistors (TFTs) in flat-panel displays that are fabricated using vacuum-processes, there is a growing interest in the fabrication of metal oxide TFTs by means of scalable, low-cost solution and printing processes for applications such as flexible displays and biosensors. Although devices with printed semiconductor and gate insulator can exhibit good electrical performance, source/drain-contacts (S/D) printed from silver (Ag) nanoparticles (NPs) typically suffer from deteriorated electrical characteristics and stability problems. On the other hand, metals providing good contacts, such as aluminum (Al), titanium (Ti) and molybdenum (Mo), cannot be formed as air-stable NPs. To overcome these issues, we have developed a patterning method based on high-resolution reverse-offset printing (ROP) of a sacrificial polymer resist layer. ROP delivers patterns with micrometer-level resolution and steep sidewalls, which are ideal for patterning vacuum-deposited metal contacts at high resolution via lift-off process. Solution-processed indium oxide (In2O3) TFTs were successfully fabricated by using ROP lift-off process for patterning of gate and S/D-electrodes using Al. The fabricated In2O3-based TFTs with Al S/D-contacts exhibit good uniformity, constant mobility (μ sat) ∼ 2 cm2 (V s)−1 over a wide range of width/length-ratios (W/L) and almost zero turn-on voltage (V on) ∼ −0.2 V. TFTs down to 5 µm channel lengths were successfully patterned. Further development of the fabrication process could lead to flexible fully-print-patterned high-resolution TFT backplanes for flexible displays, biosensors, photosensors and x-ray detectors.
- Open Access
- 22 January 2023
- Published by Wiley in Advanced Materials Interfaces
- Vol. 10 (7)
Focused Review on Print‐Patterned Contact Electrodes for Metal‐Oxide Thin‐Film Transistors
Metal‐oxide‐semiconductor‐based thin‐film transistors (TFTs) are exploited in display backplanes and X‐ray detectors fabricated by vacuum deposition and lithographic patterning. However, there is growing interest to use scalable printing technologies to lower the environmental impact and cost of processing. There have been substantial research efforts on oxide dielectric and semiconductor materials and their interfaces. Materials for the source/drain (S/D) contact electrodes and their interface to the semiconductor have received less attention, particularly concerning the usage of printing processes. Specific contact resistivity of oxide TFTs with print‐patterned S/D contacts can be 10−2 to 101 Ω cm2, significantly higher than vacuum‐deposited contacts around 10−5 to 10−3 Ω cm2. Problems at the semiconductor/S/D interface, such as large contact resistance, poor adhesion, or cross‐interface contact material migration, affect device characteristics causing hysteresis loops, kink or step‐like distortion, and threshold voltage shift. This work reviews advances in materials and fabrication methods of print‐patterned S/D electrodes for oxide TFTs. Differences in characterization methods among existing literature hamper comparing the performance of print‐patterned S/D contacts. Therefore, systematic and standardized measurements are proposed to assist identification of possible problems, which to some degree can then be mitigated by device fabrication strategies, facilitating well‐performing printed contact electrodes for metal‐oxide TFTs.
- 22 January 2023
- Published by Wiley in Advanced Materials Interfaces
- Vol. 10 (7)
Open AccessFocused Review on Print‐Patterned Contact Electrodes for Metal‐Oxide Thin‐Film Transistors
Metal‐oxide‐semiconductor‐based thin‐film transistors (TFTs) are exploited in display backplanes and X‐ray detectors fabricated by vacuum deposition and lithographic patterning. However, there is growing interest to use scalable printing technologies to lower the environmental impact and cost of processing. There have been substantial research efforts on oxide dielectric and semiconductor materials and their interfaces. Materials for the source/drain (S/D) contact electrodes and their interface to the semiconductor have received less attention, particularly concerning the usage of printing processes. Specific contact resistivity of oxide TFTs with print‐patterned S/D contacts can be 10−2 to 101 Ω cm2, significantly higher than vacuum‐deposited contacts around 10−5 to 10−3 Ω cm2. Problems at the semiconductor/S/D interface, such as large contact resistance, poor adhesion, or cross‐interface contact material migration, affect device characteristics causing hysteresis loops, kink or step‐like distortion, and threshold voltage shift. This work reviews advances in materials and fabrication methods of print‐patterned S/D electrodes for oxide TFTs. Differences in characterization methods among existing literature hamper comparing the performance of print‐patterned S/D contacts. Therefore, systematic and standardized measurements are proposed to assist identification of possible problems, which to some degree can then be mitigated by device fabrication strategies, facilitating well‐performing printed contact electrodes for metal‐oxide TFTs.
- Open Access
- 19 September 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 10 (40) , 15126-15136
Rhodamine 6G and phloxine B as photosensitizers for inkjet-printed indium oxide phototransistors
An inkjet-printed rhodamine 6G/InOx photosensitizing interlayer for In2O3 thin-film phototransistors enables photosensitivity of 4.1 × 105 and responsivity of 250 A W−1.
- 19 September 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 10 (40) , 15126-15136
Open AccessRhodamine 6G and phloxine B as photosensitizers for inkjet-printed indium oxide phototransistors
An inkjet-printed rhodamine 6G/InOx photosensitizing interlayer for In2O3 thin-film phototransistors enables photosensitivity of 4.1 × 105 and responsivity of 250 A W−1.