Mareen Warncke

Textile‐integrated strain sensors enable close‐to‐body motion monitoring, but performance depends strongly on textile architecture. Embroidered and weft‐knitted Smart Kinesiotapes incorporating the same silver‐plated polyamide yarn are compared using five specimens per configuration under cyclic elongation in increments up to . The effects of sensor geometry, sensing‐path length and knitting orientation on base resistance, drift and relative resistance change are evaluated. Vertical orientation reduces one‐line base resistance from to , corresponding to , and four‐line base resistance from to , corresponding to . Compared with the corresponding vertical structures, the relative resistance changes of the horizontal one‐ and four‐line variants are and lower, respectively. The vertical variants provide distinct cyclic signals and close temporal agreement with the applied strain. For the embroidered sensors, the straight geometry provides the largest response, whereas extending the sensing path to four lines increases base resistance without amplifying the relative response. The one‐line vertically knitted sensor provides the most promising combination of low base resistance, high sensitivity and signal interpretability. These findings provide design guidance for body‐conforming textile strain sensors.

Functional electrical stimulation (FES) aims to improve the gait pattern in cases of weak foot dorsiflexion (foot lifter weakness) and, therefore, increase the liveability of people suffering from chronic diseases of the central nervous system, e.g., multiple sclerosis. One important component of FES is the detection of the knee angle in order to enable the situational triggering of dorsiflexion in the right gait phase by electrical impulses. This paper presents an alternative approach to sensors for motion capture in the form of weft-knitted strain sensors. The use of textile-based strain sensors instead of conventional strain gauges offers the major advantage of direct integration during the knitting process and therefore a very discreet integration into garments. This in turn contributes to the fact that the FES system can be implemented in the form of functional leggings that are suitable for inconspicuous daily use without disturbing the wearer unnecessarily. Different designs of the weft-knitted strain sensor and the influence on its measurement behavior were investigated. The designs differed in terms of the integration direction of the sensor (wale- or course-wise) and the width of the sensor (number of loops) in a weft-knitted textile structure.

This paper presents the simulation-based development of a novel knitted design of textile heating structures based on dedicated serial-parallel circuits for heating (DSPCh) using silver-plated yarns processed via knitting technology. The DSPCh approach features dedicated and spatially bounded sub-circuits, ensuring even heat distribution and resilience against circuit failures in smart textiles with heating functionality. The study finds that the conductor arrangement and knitting pattern significantly affect the heating performance. DSPCh structures achieve even more heat distribution than serial and parallel circuit designs. Due to its binding, the developed basic pattern based on the right–left knit is less electrically conductive than that based on the right–right knit. Results show that DSPCh structures exhibit a favorable heat level and uniform heat distribution suitable for wearable textiles close to the body. The comparison with other circuit designs demonstrates higher temperatures of maximum 132°C and temperature differences up to 100 K, making DSPCh structures suitable for functional underwear. In addition, the experiments reveal that the heating performance is minimally degraded after standard machine-washing and care protocols. The investigations demonstrate that the DSPCh structures are suitable for actively heatable functional underwear, and simulation tools can aid in predicting temperatures and heat distribution for various textile designs.

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. However, the challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investigation of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for motion capture for medical devices. Several variables are considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through an experimental evaluation, by determining the gauge factor, its nonlinearity, hysteresis, and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50%, 12.5% hysteresis, and 0.3% nonlinearity in parts.

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. How-ever, challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investiga-tion of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for mo-tion capture for medical devices. Several variables were considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through experimental evaluation, by determining the gauge factor, its non-linearity, hysteresis and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50 %, 12,5 % hysteresis, and 0.3 % nonlinearity in parts.

Functional electrical stimulation (FES) aims to improve the gait pattern in case of foot drop of people suffering chronic diseases, e.g., multiple sclerosis. The fibular nerve can be stimulated by electrical impulses sent through electrodes on the skin, which leads to the contraction of the corresponding muscles. One major disadvantage of commercial FES devices is their bulky design. The paper presents an alternative approach of weft-knitted strain sensors that are directly integrated into the knee area of a functional legging suitable for daily use. To initiate electrical impulses for FES at the right time, the textile strain sensors are used as soft triggers.