Shasvat Rathod
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shasvat Rathod has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Joshua Jones
Centre for Advanced Materials Joining, Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Avenue West, Waterloo, Ontario N2L 3G1, Canada
2 shared publications - Monika R. Snowdon
Centre for Advanced Materials Joining, University of Waterloo, 200 University Ave. West, Waterloo, Ontario N2L 3G1, Canada
2 shared publications Monika Snowdon
2 shared publicationsPeng Peng
2 shared publications- Peng Peng
University of Waterloo
2 shared publications Kaiping Zhang
Centre for Advanced Materials Joining, Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Avenue West, Waterloo, Ontario N2L 3G1, Canada
1 shared publication
Latest Publications
- Open Access
- 10 December 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale Advances
- Vol. 7 (3) , 766-783
Laser writing of metal-oxide doped graphene films for tunable sensor applications
Flexible and wearable devices play a pivotal role in the realm of smart portable electronics due to their diverse applications in healthcare monitoring, soft robotics, human–machine interfaces, and artificial intelligence. Nonetheless, the extensive integration of intelligent wearable sensors into mass production faces challenges within a resource-limited environment, necessitating low-cost manufacturing, high reliability, stability, and multi-functionality. In this study, a cost-effective fiber laser direct writing method (fLDW) was illustrated to create highly responsive and robust flexible sensors. These sensors integrate laser-induced graphene (LiG) with mixed metal oxides on a flexible polyimide film. fLDW simplifies the synthesis of graphene, functionalization of carbon structures into graphene oxides and reduced graphene oxides, and deposition of metal-oxide nanoparticles within a single experimental laser writing setup. The preparation and surface modification of dense oxygenated graphene networks and semiconducting metal oxide nanoparticles (CuOx, ZnOx, FeOx) enables rapid fabrication of LiG/MOx composite sensors with the ability to detect and differentiate various stimuli, including visible light, UV light, temperature, humidity, and magnetic fluxes. Further, this in situ customizability of fLDW-produced sensors allows for tunable sensitivity, response time, recovery time, and selectivity. The normalized current gain of resistive LiG/MOx sensors can be controlled between −2.7 to 3.5, with response times ranging from 0.02 to 15 s, and recovery times from 0.04 to 6 s. Furthermore, the programmable properties showed great endurance after 200 days in air and extended bend cycles. Collectively, these LiG/MOx sensors stand as a testament to the effectiveness of fLDW in economically mass-producing flexible and wearable electronic devices to meet the explicit demands of the Internet of Things.
- 10 December 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale Advances
- Vol. 7 (3) , 766-783
Open AccessLaser writing of metal-oxide doped graphene films for tunable sensor applications
Flexible and wearable devices play a pivotal role in the realm of smart portable electronics due to their diverse applications in healthcare monitoring, soft robotics, human–machine interfaces, and artificial intelligence. Nonetheless, the extensive integration of intelligent wearable sensors into mass production faces challenges within a resource-limited environment, necessitating low-cost manufacturing, high reliability, stability, and multi-functionality. In this study, a cost-effective fiber laser direct writing method (fLDW) was illustrated to create highly responsive and robust flexible sensors. These sensors integrate laser-induced graphene (LiG) with mixed metal oxides on a flexible polyimide film. fLDW simplifies the synthesis of graphene, functionalization of carbon structures into graphene oxides and reduced graphene oxides, and deposition of metal-oxide nanoparticles within a single experimental laser writing setup. The preparation and surface modification of dense oxygenated graphene networks and semiconducting metal oxide nanoparticles (CuOx, ZnOx, FeOx) enables rapid fabrication of LiG/MOx composite sensors with the ability to detect and differentiate various stimuli, including visible light, UV light, temperature, humidity, and magnetic fluxes. Further, this in situ customizability of fLDW-produced sensors allows for tunable sensitivity, response time, recovery time, and selectivity. The normalized current gain of resistive LiG/MOx sensors can be controlled between −2.7 to 3.5, with response times ranging from 0.02 to 15 s, and recovery times from 0.04 to 6 s. Furthermore, the programmable properties showed great endurance after 200 days in air and extended bend cycles. Collectively, these LiG/MOx sensors stand as a testament to the effectiveness of fLDW in economically mass-producing flexible and wearable electronic devices to meet the explicit demands of the Internet of Things.
- 4 December 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (49) , 57314-57326
In Situ Rapid Fabrication of Graphene–Copper Heterojunctions Using Fiber Laser Direct Writing
Multifunctional three-dimensional heterostructures for flexible electronics have gained significant attention due to their distinctive structural formability and superior electronic and optoelectronic properties. Nevertheless, conventional fabrication techniques have yet to be optimized for flexible substrates. In this study, a straightforward fiber laser direct writing (FLDW) process is demonstrated for the simultaneous fabrication of diodes (PN junctions) and bipolar junction transistors (BJTs) on flexible polyimide substrates, which is realized through the deposition of multifunctional p- or n-type copper oxide films (CuOx) and p- or n-type porous laser-reduced graphene oxide films (LrGO) using fiber laser ablation and deposition. The presence of both p- and n-type semiconductor films is confirmed through material characterization. The fabricated PN junctions exhibit reasonable diode rectification ratios, ranging from 20 to 220, and perform reliably under numerous operating conditions such as light-dark illumination and elevated temperatures. Furthermore, I-V curve analysis indicates that the current gain and electrical performance of printed negative-positive-negative (NPN) (or positive-negative-positive, PNP) BJTs can be tailored by adjusting the laser energy density of the FLDW process and the base gap width of the BJTs. As a proof of concept, the FLDW process is successfully employed to deposit both NPN (or PNP) BJTs composed of LrGO/CuOx heterostructures with controlled current gains. Its ease of operation, versatility, and cost-effectiveness make FLDW promising for large-scale flexible electronics fabrication.
- 4 December 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (49) , 57314-57326
In Situ Rapid Fabrication of Graphene–Copper Heterojunctions Using Fiber Laser Direct Writing
Multifunctional three-dimensional heterostructures for flexible electronics have gained significant attention due to their distinctive structural formability and superior electronic and optoelectronic properties. Nevertheless, conventional fabrication techniques have yet to be optimized for flexible substrates. In this study, a straightforward fiber laser direct writing (FLDW) process is demonstrated for the simultaneous fabrication of diodes (PN junctions) and bipolar junction transistors (BJTs) on flexible polyimide substrates, which is realized through the deposition of multifunctional p- or n-type copper oxide films (CuOx) and p- or n-type porous laser-reduced graphene oxide films (LrGO) using fiber laser ablation and deposition. The presence of both p- and n-type semiconductor films is confirmed through material characterization. The fabricated PN junctions exhibit reasonable diode rectification ratios, ranging from 20 to 220, and perform reliably under numerous operating conditions such as light-dark illumination and elevated temperatures. Furthermore, I-V curve analysis indicates that the current gain and electrical performance of printed negative-positive-negative (NPN) (or positive-negative-positive, PNP) BJTs can be tailored by adjusting the laser energy density of the FLDW process and the base gap width of the BJTs. As a proof of concept, the FLDW process is successfully employed to deposit both NPN (or PNP) BJTs composed of LrGO/CuOx heterostructures with controlled current gains. Its ease of operation, versatility, and cost-effectiveness make FLDW promising for large-scale flexible electronics fabrication.
- Open Access
- 31 January 2023
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 8 (1) , 015008
Direct laser writing of copper and copper oxide structures on plastic substrates for memristor devices
Rapid fabrication of flexible electronics is attracting much attention in many industries. There is a need to rapidly produce flexible electronic components without relying on costly precursor materials and complex processes. This work presents a direct laser writing (DLW) process capable of rapidly depositing flexible copper or copper oxide structures with a high degree of control over electrical properties. The DLW process uses a low-power fiber laser beam to selectively irradiate a thin film of copper ions to form and interconnect copper nanoparticles. The electrical properties of the deposited patterns can be controlled by tuning laser power, scanning speed, and beam defocus. The microstructures of patterns printed at varying laser powers are investigated using scanning electron microscopy, x-ray photoelectron spectroscopy, and x-ray powder diffraction and the relation between laser power and sheet resistance is explored. The results showed that high laser energy densities resulted in highly conductive patterns of metallic copper, whereas lower energy patterns resulted in copper oxide-rich patterns with significantly lower conductivity. This method can produce high-quality flexible electronic components with a range of potential applications, as demonstrated by the proof-of-concept fabrication of a flexible memristive junction with resistive switching observed at ±0.7 V and a R on/R off ratio of 102.
- 31 January 2023
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 8 (1) , 015008
Open AccessDirect laser writing of copper and copper oxide structures on plastic substrates for memristor devices
Rapid fabrication of flexible electronics is attracting much attention in many industries. There is a need to rapidly produce flexible electronic components without relying on costly precursor materials and complex processes. This work presents a direct laser writing (DLW) process capable of rapidly depositing flexible copper or copper oxide structures with a high degree of control over electrical properties. The DLW process uses a low-power fiber laser beam to selectively irradiate a thin film of copper ions to form and interconnect copper nanoparticles. The electrical properties of the deposited patterns can be controlled by tuning laser power, scanning speed, and beam defocus. The microstructures of patterns printed at varying laser powers are investigated using scanning electron microscopy, x-ray photoelectron spectroscopy, and x-ray powder diffraction and the relation between laser power and sheet resistance is explored. The results showed that high laser energy densities resulted in highly conductive patterns of metallic copper, whereas lower energy patterns resulted in copper oxide-rich patterns with significantly lower conductivity. This method can produce high-quality flexible electronic components with a range of potential applications, as demonstrated by the proof-of-concept fabrication of a flexible memristive junction with resistive switching observed at ±0.7 V and a R on/R off ratio of 102.