Thomas Fontaine
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thomas Fontaine has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- François Reniers
Chemistry of Surfaces, Interfaces, and Nanomaterials, ChemSIN, Université Libre de Bruxelles, Faculty of Sciences, Brussels, Belgium
3 shared publications Rony Snyders
Chimie des Interactions Plasma-Surfaces (ChIPS), Department of Chemistry, Université de Mons, Mons, Belgium
2 shared publications- Alain Delchambre
Bio-, Electro- and Mechanical- Systems (BEAMS), Biomed Group, Ecole Polytechnique de Bruxelles, Brussels, Belgium
1 shared publication - Annemie Bogaerts
Research Group PLASMANT and Center of Excellence PLASMA, Department of Chemistry, University of Antwerp, Antwerp, Belgium
1 shared publication - Antoine Nonclercq
Universite Libre de Bruxelles
1 shared publication - Dominique Petitjean
Chemistry of Surfaces, Interfaces and Nanomaterials (ChemSIN), Faculty of Sciences, Université libre de Bruxelles 1 , Ixelles, 1050
1 shared publication
Latest Publications
- 17 July 2026
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 46 (5) , 89
From AC to Nanosecond Pulses: Impact of Pulse Duration on Methane Non-oxidative Conversion in a DBD
- 17 July 2026
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 46 (5) , 89
From AC to Nanosecond Pulses: Impact of Pulse Duration on Methane Non-oxidative Conversion in a DBD
- 17 June 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (4)
Tuning the crystallinity of TiO2 coatings synthesized by an atmospheric pressure dielectric barrier discharge in a single step process
Titanium dioxide in its anatase form is of significant interest nowadays due to numerous properties such as biocompatibility, photoactivity under ultraviolet irradiation, or corrosion resistance. In this paper, titanium dioxide (TiO2) films are synthesized with a controlled substrate temperature going up to 673 K. Crystalline anatase was synthesized in a low power atmospheric pressure dielectric barrier discharge in a single step process. The effect of deposition parameters (plasma gas, the voltage input, precursor flow, deposition time, and substrate temperature) on the crystal size, crystallinity, and coating morphology was studied. It shows that the crystal size can be tuned, that the layers can have a transition from hydrophilicity to hydrophobicity, and that the coating morphology can be modified by optimizing these parameters. Finally, it is found that crystalline anatase TiO2 can be grown at a substrate temperature as low as 523 K in an atmospheric pressure plasma enhanced chemical vapor deposition process.
- 17 June 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (4)
Tuning the crystallinity of TiO2 coatings synthesized by an atmospheric pressure dielectric barrier discharge in a single step process
Titanium dioxide in its anatase form is of significant interest nowadays due to numerous properties such as biocompatibility, photoactivity under ultraviolet irradiation, or corrosion resistance. In this paper, titanium dioxide (TiO2) films are synthesized with a controlled substrate temperature going up to 673 K. Crystalline anatase was synthesized in a low power atmospheric pressure dielectric barrier discharge in a single step process. The effect of deposition parameters (plasma gas, the voltage input, precursor flow, deposition time, and substrate temperature) on the crystal size, crystallinity, and coating morphology was studied. It shows that the crystal size can be tuned, that the layers can have a transition from hydrophilicity to hydrophobicity, and that the coating morphology can be modified by optimizing these parameters. Finally, it is found that crystalline anatase TiO2 can be grown at a substrate temperature as low as 523 K in an atmospheric pressure plasma enhanced chemical vapor deposition process.
- 28 February 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (12) , 125201
Electrical equivalent model of a long dielectric barrier discharge plasma jet for endoscopy
Cold atmospheric plasmas are a known source of reactive species enabling various treatments, from the healing of chronic wounds to the treatment of surface cancers. Therapeutic endoscopic procedures require developing specific flexible tools that can be used through or alongside endoscopes. Plasma devices for endoscopy have aroused significant research interest over the past few decades, but their electrical behaviour is not yet fully understood and predictable. There is thus a clear need for a robust model that provides a way to understand and optimize future devices. In this work, for the first time, an electrical equivalent model of a long plasma source (comprising plasma generation, transport and target interaction) was designed, implemented, and validated. System parameters were estimated based on the system geometry and independent measurements. The model reliably reproduces the double ignition (in the quartz chamber and at the treatment site) observed experimentally. Simulations globally agree with measurements taken for various gas gap distances and input voltages. Internal parameters that are difficult to measure, such as the electrical charge at the gas gaps, were inferred. The model can predict leakage current in the body and current at the target site. This work provides a new understanding of endoscopic plasma systems that could be used in the future to ensure patient and operator safety.
- 28 February 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (12) , 125201
Electrical equivalent model of a long dielectric barrier discharge plasma jet for endoscopy
Cold atmospheric plasmas are a known source of reactive species enabling various treatments, from the healing of chronic wounds to the treatment of surface cancers. Therapeutic endoscopic procedures require developing specific flexible tools that can be used through or alongside endoscopes. Plasma devices for endoscopy have aroused significant research interest over the past few decades, but their electrical behaviour is not yet fully understood and predictable. There is thus a clear need for a robust model that provides a way to understand and optimize future devices. In this work, for the first time, an electrical equivalent model of a long plasma source (comprising plasma generation, transport and target interaction) was designed, implemented, and validated. System parameters were estimated based on the system geometry and independent measurements. The model reliably reproduces the double ignition (in the quartz chamber and at the treatment site) observed experimentally. Simulations globally agree with measurements taken for various gas gap distances and input voltages. Internal parameters that are difficult to measure, such as the electrical charge at the gas gaps, were inferred. The model can predict leakage current in the body and current at the target site. This work provides a new understanding of endoscopic plasma systems that could be used in the future to ensure patient and operator safety.