Oliver M. F. Browne
Oliver M. F. Browne has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Eusebio Valero
School of Aeronautics, Universidad Politécnica de Madrid, 28040 Madrid, Spain
3 shared publications Aditya S. Ghate
NASA Ames Research Center, Moffett Field, California 94035
2 shared publicationsCetin C. Kiris
NASA Ames Research Center, Moffett Field, California 94035
2 shared publications- Christoph Brehm
Department of Aerospace Engineering, University of Maryland, College Park, USA
2 shared publications - Esteban Ferrer
Universidad Politécnica de Madrid
2 shared publications Jeffrey A. Housman
NASA Ames Research Center
2 shared publications
Latest Publications
- 1 January 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 62 (1) , 62-80
Predicting Transonic Buffet Onset for the Boeing Transonic Truss-Braced Wing Aircraft
The flow past the Boeing Transonic Truss-Braced Wing (TTBW) aircraft is simulated with a Hybrid Reynolds-Averaged Navier–Stokes Large-Eddy Simulations (HRLES) turbulence modeling approach to study transonic buffet onset and evaluate the predictive capability of the numerical approach. The HRLES model that is used in this work is a zonal detached eddy simulations (ZDES) method. All simulations used structured overset curvilinear grids for the free-air configuration, with all simulations performed using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework. Aerodynamic loads and surface pressure obtained from the HRLES solutions are compared to results from unsteady RANS (URANS) and experiments conducted at NASA Ames Research Center 11- by 11-Foot Transonic Wind Tunnel. Overall good agreement is obtained in the predicted loads and surface pressure. Unsteady pressure data from HRLES and URANS simulations is used to compute the power spectral density (PSD) to predict transonic buffet onset and compared to the Kulite data obtained from the experiment. Comparisons of the PSD spectrum also show reasonable agreement with the wind-tunnel data, with HRLES and URANS predicting buffet onset at a slightly earlier angle of attack than the experiment.
- 1 January 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 62 (1) , 62-80
Predicting Transonic Buffet Onset for the Boeing Transonic Truss-Braced Wing Aircraft
The flow past the Boeing Transonic Truss-Braced Wing (TTBW) aircraft is simulated with a Hybrid Reynolds-Averaged Navier–Stokes Large-Eddy Simulations (HRLES) turbulence modeling approach to study transonic buffet onset and evaluate the predictive capability of the numerical approach. The HRLES model that is used in this work is a zonal detached eddy simulations (ZDES) method. All simulations used structured overset curvilinear grids for the free-air configuration, with all simulations performed using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework. Aerodynamic loads and surface pressure obtained from the HRLES solutions are compared to results from unsteady RANS (URANS) and experiments conducted at NASA Ames Research Center 11- by 11-Foot Transonic Wind Tunnel. Overall good agreement is obtained in the predicted loads and surface pressure. Unsteady pressure data from HRLES and URANS simulations is used to compute the power spectral density (PSD) to predict transonic buffet onset and compared to the Kulite data obtained from the experiment. Comparisons of the PSD spectrum also show reasonable agreement with the wind-tunnel data, with HRLES and URANS predicting buffet onset at a slightly earlier angle of attack than the experiment.
- 1 July 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 60 (4) , 1118-1140
HLPW-4: Wall-Modeled Large-Eddy Simulation and Lattice–Boltzmann Technology Focus Group Workshop Summary
A summary of the nine submissions to the Wall-Modeled Large-Eddy Simulation and Lattice–Boltzmann (WMLESLB) Technical Focus Group (TFG) at the 4th High lift Prediction Workshop is provided. The focus of this TFG was to assess the current capabilities of WMLES and LB methods on a complex high-lift configuration across a wide range of angles of attack. Analysis of the submitted data suggests that [ ] spatial degrees of freedom are needed to accurately predict pitching moments at high angles of attack due to large pressure gradients present on the outboard slat and main element for [ ] (corrected for free-air). While some scatter is reported in pitching moment coefficient at the low-angles of attack ([ ]), excellent agreement is observed between submissions near the [ ] state. Objective superiority of WMLES methods over Reynolds-averaged Navier–Stokes (RANS) can be seen in terms of lack of excess outboard separation; a majority of the WMLES and LB submissions predict wedge-shaped separation patterns consistent with the experimental oil flow. The in-tunnel simulations show excellent agreement with the experiment in terms of a) integrated loads, b) surface flow-topology, and c) mechanism for the onset of inboard stall. Further evidence is provided to demonstrate both qualitative and quantitative superiority of the WMLES submissions over RANS.
- 1 July 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 60 (4) , 1118-1140
HLPW-4: Wall-Modeled Large-Eddy Simulation and Lattice–Boltzmann Technology Focus Group Workshop Summary
A summary of the nine submissions to the Wall-Modeled Large-Eddy Simulation and Lattice–Boltzmann (WMLESLB) Technical Focus Group (TFG) at the 4th High lift Prediction Workshop is provided. The focus of this TFG was to assess the current capabilities of WMLES and LB methods on a complex high-lift configuration across a wide range of angles of attack. Analysis of the submitted data suggests that [ ] spatial degrees of freedom are needed to accurately predict pitching moments at high angles of attack due to large pressure gradients present on the outboard slat and main element for [ ] (corrected for free-air). While some scatter is reported in pitching moment coefficient at the low-angles of attack ([ ]), excellent agreement is observed between submissions near the [ ] state. Objective superiority of WMLES methods over Reynolds-averaged Navier–Stokes (RANS) can be seen in terms of lack of excess outboard separation; a majority of the WMLES and LB submissions predict wedge-shaped separation patterns consistent with the experimental oil flow. The in-tunnel simulations show excellent agreement with the experiment in terms of a) integrated loads, b) surface flow-topology, and c) mechanism for the onset of inboard stall. Further evidence is provided to demonstrate both qualitative and quantitative superiority of the WMLES submissions over RANS.
- 1 April 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (4) , 1639-1658
Numerical Investigation of CL,max Prediction on the NASA High-Lift Common Research Model
An assessment of a hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (HRLES) approach for [ ] prediction is presented for the NASA High-Lift Common Research Model (CRM-HL). Both free-air and wind tunnel configurations of the CRM-HL are investigated, and the results are compared to the QinetiQ wind tunnel experiments and two other numerical approaches: RANS and wall-modeled LES (WMLES). For the free-air configuration, HRLES is shown to address some of the known shortcomings with RANS and prevent inboard and outboard flow separation particularly in the region of [ ] and poststall. To achieve these improvements over RANS, LES-appropriate grids and numerical discretizations are required. It was also found that, when applying HRLES to a RANS best practice grid and numerics, the HRLES method significantly underperformed RANS. For the in-tunnel configuration, HRLES showed good agreement with the loads, surface pressure, and oil-flow photographs obtained in the experiment. HRLES was able to improve upon the RANS simulations, which showed a sharp loss of lift at the two highest angles of attack due to large-scale inboard and outboard separation on the wing, by correctly predicting the corner flow separation and showing remarkably close agreement in the flow topologies with the experiment.
- 1 April 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (4) , 1639-1658
Numerical Investigation of CL,max Prediction on the NASA High-Lift Common Research Model
An assessment of a hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (HRLES) approach for [ ] prediction is presented for the NASA High-Lift Common Research Model (CRM-HL). Both free-air and wind tunnel configurations of the CRM-HL are investigated, and the results are compared to the QinetiQ wind tunnel experiments and two other numerical approaches: RANS and wall-modeled LES (WMLES). For the free-air configuration, HRLES is shown to address some of the known shortcomings with RANS and prevent inboard and outboard flow separation particularly in the region of [ ] and poststall. To achieve these improvements over RANS, LES-appropriate grids and numerical discretizations are required. It was also found that, when applying HRLES to a RANS best practice grid and numerics, the HRLES method significantly underperformed RANS. For the in-tunnel configuration, HRLES showed good agreement with the loads, surface pressure, and oil-flow photographs obtained in the experiment. HRLES was able to improve upon the RANS simulations, which showed a sharp loss of lift at the two highest angles of attack due to large-scale inboard and outboard separation on the wing, by correctly predicting the corner flow separation and showing remarkably close agreement in the flow topologies with the experiment.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Disturbance Flow Field Analysis of Particulate Interaction with High Speed Boundary Layers
The current work is a follow-up study on numerical simulations of particulate-induced transition for hypersonic boundary layer flows. While prior works have focused on obtaining an efficient and highly accurate simulation approach, in this work the main objective is to analyze the disturbance flow field during the particle impingement phase and its subsequent downstream evolution. Particulate impingement simulations were conducted employing the adaptive mesh refinement wave-packet tracking technique for a plate boundary-layer flow with a freestream Mach number of 5.35 and an isothermal wall at 300K. The disturbance flow field was analyzed by computing frequency spectra for wall pressure along streamwise direction and distributions of the different unsteady disturbance flow quantities at a position in the vicinity of the particle impingement location and further downstream where the mode S (for these conditions, commonly referred to as second mode) dominated wave-packet has been fully established. Biorthogonal decomposition was used to project the disturbance flow field onto normal modes and gain insight into the contributions from the different discrete and continuous modes to the disturbance flow field, and, in particular, to understand how the disturbance energy is translated into mode S.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Disturbance Flow Field Analysis of Particulate Interaction with High Speed Boundary Layers
The current work is a follow-up study on numerical simulations of particulate-induced transition for hypersonic boundary layer flows. While prior works have focused on obtaining an efficient and highly accurate simulation approach, in this work the main objective is to analyze the disturbance flow field during the particle impingement phase and its subsequent downstream evolution. Particulate impingement simulations were conducted employing the adaptive mesh refinement wave-packet tracking technique for a plate boundary-layer flow with a freestream Mach number of 5.35 and an isothermal wall at 300K. The disturbance flow field was analyzed by computing frequency spectra for wall pressure along streamwise direction and distributions of the different unsteady disturbance flow quantities at a position in the vicinity of the particle impingement location and further downstream where the mode S (for these conditions, commonly referred to as second mode) dominated wave-packet has been fully established. Biorthogonal decomposition was used to project the disturbance flow field onto normal modes and gain insight into the contributions from the different discrete and continuous modes to the disturbance flow field, and, in particular, to understand how the disturbance energy is translated into mode S.
- Open Access
Sensitivity Analysis to Control the Far-Wake Unsteadiness Behind Turbines
We explore the stability of wakes arising from 2D flow actuators based on linear momentum actuator disc theory. We use stability and sensitivity analysis (using adjoints) to show that the wake stability is controlled by the Reynolds number and the thrust force (or flow resistance) applied through the turbine. First, we report that decreasing the thrust force has a comparable stabilising effect to a decrease in Reynolds numbers (based on the turbine diameter). Second, a discrete sensitivity analysis identifies two regions for suitable placement of flow control forcing, one close to the turbines and one far downstream. Third, we show that adding a localised control force, in the regions identified by the sensitivity analysis, stabilises the wake. Particularly, locating the control forcing close to the turbines results in an enhanced stabilisation such that the wake remains steady for significantly higher Reynolds numbers or turbine thrusts. The analysis of the controlled flow fields confirms that modifying the velocity gradient close to the turbine is more efficient to stabilise the wake than controlling the wake far downstream. The analysis is performed for the first flow bifurcation (at low Reynolds numbers) which serves as a foundation of the stabilization technique but the control strategy is tested at higher Reynolds numbers in the final section of the paper, showing enhanced stability for a turbulent flow case.
Open AccessSensitivity Analysis to Control the Far-Wake Unsteadiness Behind Turbines
We explore the stability of wakes arising from 2D flow actuators based on linear momentum actuator disc theory. We use stability and sensitivity analysis (using adjoints) to show that the wake stability is controlled by the Reynolds number and the thrust force (or flow resistance) applied through the turbine. First, we report that decreasing the thrust force has a comparable stabilising effect to a decrease in Reynolds numbers (based on the turbine diameter). Second, a discrete sensitivity analysis identifies two regions for suitable placement of flow control forcing, one close to the turbines and one far downstream. Third, we show that adding a localised control force, in the regions identified by the sensitivity analysis, stabilises the wake. Particularly, locating the control forcing close to the turbines results in an enhanced stabilisation such that the wake remains steady for significantly higher Reynolds numbers or turbine thrusts. The analysis of the controlled flow fields confirms that modifying the velocity gradient close to the turbine is more efficient to stabilise the wake than controlling the wake far downstream. The analysis is performed for the first flow bifurcation (at low Reynolds numbers) which serves as a foundation of the stabilization technique but the control strategy is tested at higher Reynolds numbers in the final section of the paper, showing enhanced stability for a turbulent flow case.
- 30 June 2017
- Published by Springer Nature
- p. 207-222
Numerical and Parametric Study of MVGs on a UAV Geometry in Subsonic Flow
- 30 June 2017
- Published by Springer Nature
- p. 207-222
Numerical and Parametric Study of MVGs on a UAV Geometry in Subsonic Flow
- 13 October 2014
- Published by Wiley in International Journal for Numerical Methods in Fluids
- Vol. 76 (12) , 1088-1110
Sensitivity analysis to unsteady perturbations of complex flows: a discrete approach
SUMMARY: A discrete framework for computing the global stability and sensitivity analysis to external perturbations for any set of partial differential equations is presented. In particular, a complex‐step approximation is used to achieve near analytical accuracy for the evaluation of the Jacobian matrix. Sensitivity maps for the sensitivity to base flow modifications and to a steady force are computed to identify regions of the flow field where an input could have a stabilising effect. Four test cases are presented: (1) an analytical test case to prove the theory of the discrete framework, (2) a lid‐driven cavity at low Reynolds case to show the improved accuracy in the calculation of the eigenvalues when using the complex‐step approximation, (3) the 2D flow past a circular cylinder at just below the critical Reynolds number used to validate the methodology, and finally, (4) the flow past an open cavity presented to give an example of the discrete method applied to a convectively unstable case. The latter three (2–4) of the aforementioned cases were solved with the 2D compressible Navier–Stokes equations using a Discontinuous Galerkin Spectral Element Method. Good agreement was obtained for the validation test case, (3), with appropriate results in the literature. Furthermore, it is shown that for the calculation of the direct and adjoint eigenmodes and their sensitivity maps to external perturbations, the use of complex variables is paramount for obtaining an accurate prediction. Copyright © 2014 John Wiley & Sons, Ltd.
- 13 October 2014
- Published by Wiley in International Journal for Numerical Methods in Fluids
- Vol. 76 (12) , 1088-1110
Sensitivity analysis to unsteady perturbations of complex flows: a discrete approach
SUMMARY: A discrete framework for computing the global stability and sensitivity analysis to external perturbations for any set of partial differential equations is presented. In particular, a complex‐step approximation is used to achieve near analytical accuracy for the evaluation of the Jacobian matrix. Sensitivity maps for the sensitivity to base flow modifications and to a steady force are computed to identify regions of the flow field where an input could have a stabilising effect. Four test cases are presented: (1) an analytical test case to prove the theory of the discrete framework, (2) a lid‐driven cavity at low Reynolds case to show the improved accuracy in the calculation of the eigenvalues when using the complex‐step approximation, (3) the 2D flow past a circular cylinder at just below the critical Reynolds number used to validate the methodology, and finally, (4) the flow past an open cavity presented to give an example of the discrete method applied to a convectively unstable case. The latter three (2–4) of the aforementioned cases were solved with the 2D compressible Navier–Stokes equations using a Discontinuous Galerkin Spectral Element Method. Good agreement was obtained for the validation test case, (3), with appropriate results in the literature. Furthermore, it is shown that for the calculation of the direct and adjoint eigenmodes and their sensitivity maps to external perturbations, the use of complex variables is paramount for obtaining an accurate prediction. Copyright © 2014 John Wiley & Sons, Ltd.