Tianji Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tianji Zhou has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Biao Zhao
Tsinghua University
3 shared publications - Bin Cui
Department of Electrical Engineering, Tsinghua University, Beijing, China
3 shared publications - Rong Zeng
Tsinghua University
3 shared publications - Ruihang Bai
Department of Electrical Engineering, Tsinghua University, Beijing, China
3 shared publications - Zhanqing Yu
Tsinghua University
3 shared publications - Lu Qu
Department of Electrical Engineering, Tsinghua University, Beijing, China
2 shared publications
Latest Publications
- 11 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 14463-14469
Oscillation-Free Dv/dt Suppression for Medium Voltage VSCs With Series-Connected Modular Switches via Decoupled Linear Commutation
Voltage source converters (VSC) with series-connected devices offer a compact and low-cost alternative to modular multilevel converters (MMC) for medium voltage (MV) applications but suffer from excessive dv/dt. While quasi-two-level (Q2L) operation mitigates dv/dt, it imposes complexity in both circuitry and control to prevent oscillatory overcurrent. This letter proposes an oscillation-free dv/dt suppression control for MV VSCs with series-connected modular switches (MS). With a simple fixed-timing control scheme, output voltage stepping is decoupled from linear arm commutation, mitigating oscillations while preserving voltage balancing, modularity, and scalability. Experiments at 5kV dc validate the targeted dv/dt suppression with minimized module capacitance among existing solutions.
- 11 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 14463-14469
Oscillation-Free Dv/dt Suppression for Medium Voltage VSCs With Series-Connected Modular Switches via Decoupled Linear Commutation
Voltage source converters (VSC) with series-connected devices offer a compact and low-cost alternative to modular multilevel converters (MMC) for medium voltage (MV) applications but suffer from excessive dv/dt. While quasi-two-level (Q2L) operation mitigates dv/dt, it imposes complexity in both circuitry and control to prevent oscillatory overcurrent. This letter proposes an oscillation-free dv/dt suppression control for MV VSCs with series-connected modular switches (MS). With a simple fixed-timing control scheme, output voltage stepping is decoupled from linear arm commutation, mitigating oscillations while preserving voltage balancing, modularity, and scalability. Experiments at 5kV dc validate the targeted dv/dt suppression with minimized module capacitance among existing solutions.
- 22 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Dynamic Clamping Arm Control for Voltage Balancing of Series-Connected Modular Switches in MV/HV VSCs
The modular multilevel converter (MMC) is widely deployed in medium-voltage dc (MVDC) and high-voltage dc (HVDC) systems but suffers from high cost and bulky submodule capacitors. Voltage source converters (VSCs) offer a compact and cost-effective alternative but require voltage balancing control for series-connected devices in MV/HV high current applications with significant stray inductance. This work advances existing active clamping module (ACM) to self-powered, bypass-capable modular switches (MS) and proposes a dynamic clamping arm (DCA) control for series-connected MSs, enabling soft-switched recovery of turn-off energy and low-bandwidth sorting-based voltage balancing. The commutation process under DCA control is discussed in detail. Analytical models quantify voltage balancing modes and derive design constraints for key parameters of a 10kV/5MW prototype. Performance comparisons of the proposed scheme with MMC and existing balancing methods are discussed. A phase unit of the prototype, employing eight series-connected 1.7kV IGBT-based MSs per arm, is tested in a power-cycling setup. The experimental results demonstrate robust voltage balancing and minimal auxiliary switch stress, confirming the effectiveness of DCA control and its feasibility in MV/HV VSCs.
- 22 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Dynamic Clamping Arm Control for Voltage Balancing of Series-Connected Modular Switches in MV/HV VSCs
The modular multilevel converter (MMC) is widely deployed in medium-voltage dc (MVDC) and high-voltage dc (HVDC) systems but suffers from high cost and bulky submodule capacitors. Voltage source converters (VSCs) offer a compact and cost-effective alternative but require voltage balancing control for series-connected devices in MV/HV high current applications with significant stray inductance. This work advances existing active clamping module (ACM) to self-powered, bypass-capable modular switches (MS) and proposes a dynamic clamping arm (DCA) control for series-connected MSs, enabling soft-switched recovery of turn-off energy and low-bandwidth sorting-based voltage balancing. The commutation process under DCA control is discussed in detail. Analytical models quantify voltage balancing modes and derive design constraints for key parameters of a 10kV/5MW prototype. Performance comparisons of the proposed scheme with MMC and existing balancing methods are discussed. A phase unit of the prototype, employing eight series-connected 1.7kV IGBT-based MSs per arm, is tested in a power-cycling setup. The experimental results demonstrate robust voltage balancing and minimal auxiliary switch stress, confirming the effectiveness of DCA control and its feasibility in MV/HV VSCs.
- 1 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (5) , 4865-4874
PWM-Current Source Converter Based on IGCT-in-Series for DC Buck and Constant-Current Application: Topology, Design, and Experiment
PWM-current source converter (CSC) based on IGCT-in-series has the advantages in efficiency, reliability, cost, and controllability. It is a promising choice to replace silicon-controlled rectifier in dc buck and constant-current application, as well as to use in power transmission. This article firstly presents the series-IGCT-based CSC topology according to the IGCT device and CSC operation characteristics. On the basis of traditional CSC topology, di/dt-limitation inductor, absorption circuit and voltage sharing circuit are set. Secondly, the commutation process of series-IGCT-based CSC in each stage of one ac period is analyzed to obtain the coupling model between overvoltage on device and converter parameters. Furthermore, a prototype of 10kV, 1kA series-IGCT-based CSC for transmission line deicing is designed in both parameter and structure. Finally, pulse switching and power-cycling experiments of implemented prototype are carried out. The results verify that with designed parameters, overvoltage on devices is within a save range, and voltage unevenness among six units in series can be limited to 6.5%. Moreover, the prototype shows stability and reliability during long-term power-cycle operation, definitely verifying the feasibility of proposed series-IGCT-based CSC. Compared with IGBT, loss power of IGCT scheme is more than 10% lower, and reach the efficiency of 98.7%.
- 1 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (5) , 4865-4874
PWM-Current Source Converter Based on IGCT-in-Series for DC Buck and Constant-Current Application: Topology, Design, and Experiment
PWM-current source converter (CSC) based on IGCT-in-series has the advantages in efficiency, reliability, cost, and controllability. It is a promising choice to replace silicon-controlled rectifier in dc buck and constant-current application, as well as to use in power transmission. This article firstly presents the series-IGCT-based CSC topology according to the IGCT device and CSC operation characteristics. On the basis of traditional CSC topology, di/dt-limitation inductor, absorption circuit and voltage sharing circuit are set. Secondly, the commutation process of series-IGCT-based CSC in each stage of one ac period is analyzed to obtain the coupling model between overvoltage on device and converter parameters. Furthermore, a prototype of 10kV, 1kA series-IGCT-based CSC for transmission line deicing is designed in both parameter and structure. Finally, pulse switching and power-cycling experiments of implemented prototype are carried out. The results verify that with designed parameters, overvoltage on devices is within a save range, and voltage unevenness among six units in series can be limited to 6.5%. Moreover, the prototype shows stability and reliability during long-term power-cycle operation, definitely verifying the feasibility of proposed series-IGCT-based CSC. Compared with IGBT, loss power of IGCT scheme is more than 10% lower, and reach the efficiency of 98.7%.