Zhong Zheng
Zhong Zheng has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Hong Zhao
Centre for Advanced Materials Processing and Manufacturing (AMPAM) The University of Queensland Brisbane Queensland Australia
6 shared publications Ruth Knibbe
6 shared publicationsLixian Sun
Guangxi Key Laboratory of Information Materials, Guangxi Collaborative Innovation Center of Structure and Property for New Energy and Materials, School of Material Science & Engineering, Guilin University of Electronic Technology 4 , Guilin 541004, People’s Republic of China
5 shared publicationsZongwen Liu
5 shared publications- Yanping Liu
Central South University 932 South Lushan Road
4 shared publications - Behnam Akhavan
School of Biomedical Engineering, The University of Sydney, Sydney, NSW 2006, Australia
3 shared publications
Latest Publications
- Open Access
- 11 September 2026
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 289, 256-266
Thermodynamic-guided design of cost-effective ultrahigh-strength carbide-free bainitic steel
- 11 September 2026
- Published by Elsevier in Journal of Materials Science & Technology
- Vol. 289, 256-266
Open AccessThermodynamic-guided design of cost-effective ultrahigh-strength carbide-free bainitic steel
- Open Access
- 10 September 2026
- Published by Elsevier in Materials Science and Engineering: R: Reports
- Vol. 172
Probing electrochemical CO2 reduction with in-situ/operando TEM
- 10 September 2026
- Published by Elsevier in Materials Science and Engineering: R: Reports
- Vol. 172
Open AccessProbing electrochemical CO2 reduction with in-situ/operando TEM
- Open Access
- 23 March 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 122
Achieving architectured microstructures in plain carbon steel through programmed phase transformation using additive manufacturing
- 23 March 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 122
Open AccessAchieving architectured microstructures in plain carbon steel through programmed phase transformation using additive manufacturing
- Open Access
- 11 March 2026
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 391
Statistical analysis of structural descriptors governing H2O2 selectivity on oxygen-functionalized carbons
- 11 March 2026
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 391
Open AccessStatistical analysis of structural descriptors governing H2O2 selectivity on oxygen-functionalized carbons
- Open Access
- 7 March 2026
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 391
RuZr alloy supported on Zr oxynitride as efficient pH-universal hydrogen oxidation catalysts
- 7 March 2026
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 391
Open AccessRuZr alloy supported on Zr oxynitride as efficient pH-universal hydrogen oxidation catalysts
- 1 March 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (3)
Inertial mass measurements at the microscale in liquid
Mass is a fundamental property of matter that gives rise to both inertia and gravity, and its accurate quantification is central to the development of science and technology. Different technologies and methods have been developed that enable us to determine the mass of systems across length scales, from the subatomic world all the way to the cosmic scale, with such measurements generally performed in vacuum or air conditions. However, directly measuring the actual mass of objects or systems while they are submerged in liquid environments such as water remains challenging and highly debated, limiting technological developments and the understanding of fundamental processes such as the regulation of a mammalian cell’s mass. Here, we use a photothermally actuated custom-built inertial picobalance to perform cantilever-based mass measurements of well-defined silicon microweight samples in liquid environments. Our experiments demonstrate that it is possible to determine the actual mass of the samples attached to the cantilevers when submerged in water, and even within a liquid with a higher density than that of the samples themselves. We anticipate that this study will contribute to and stimulate the development and application of mass sensing techniques, facilitate the creation of new metrology solutions, and improve understanding of the behavior of microresonators in liquid environments.
- 1 March 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (3)
Inertial mass measurements at the microscale in liquid
Mass is a fundamental property of matter that gives rise to both inertia and gravity, and its accurate quantification is central to the development of science and technology. Different technologies and methods have been developed that enable us to determine the mass of systems across length scales, from the subatomic world all the way to the cosmic scale, with such measurements generally performed in vacuum or air conditions. However, directly measuring the actual mass of objects or systems while they are submerged in liquid environments such as water remains challenging and highly debated, limiting technological developments and the understanding of fundamental processes such as the regulation of a mammalian cell’s mass. Here, we use a photothermally actuated custom-built inertial picobalance to perform cantilever-based mass measurements of well-defined silicon microweight samples in liquid environments. Our experiments demonstrate that it is possible to determine the actual mass of the samples attached to the cantilevers when submerged in water, and even within a liquid with a higher density than that of the samples themselves. We anticipate that this study will contribute to and stimulate the development and application of mass sensing techniques, facilitate the creation of new metrology solutions, and improve understanding of the behavior of microresonators in liquid environments.
- 22 December 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Reduced Graphene Oxide- and Triethanolamine-Decorated Nickel Oxide Electrocatalyst for Efficient Water/Saline Water Oxidation
The development of low-cost, highly efficient catalysts for the oxygen evolution reaction (OER) is one of the key steps for advancing renewable energy production. Increasing the density of high-valence metal species, coupled with rapid surface reconstruction, is a promising, but challenging design strategy for efficient OER catalysts. Herein, we report a facile electronic modulation approach for Ni oxide catalyst design (Ni/CP-TEA-GO), achieved by codecorating the surface with reduced graphene oxide (GO) and an N-group-containing ligand, triethanolamine (TEA), via a simple two-step electrodeposition process. The electrochemically reduced GO serves as an anchor site to couple the Ni sites and induces strong electronic interactions with the Ni sites, improving stability and promoting the formation of high-valence Ni species as active sites. Concurrently, the leaching of TEA further accelerates the generation of high-valence Ni species under the anodic potential. This functional surface modification approach is both cost-effective and scalable, distinguishing it from more complex or noble-metal-based strategies. The Ni/CP-TEA-GO exhibits outstanding OER performance, with a low overpotential of 230 mV at 10 mA·cm-2, rapid OER kinetics with a small Tafel slope of 31 mV·dec-1, and great long-term stability. Moreover, it achieves an overpotential of 360 mV to drive a current density of 50 mV·cm-2 for simulated alkaline seawater oxidation, exhibiting remarkable durability over a 100-h test. This work presents an effective and simple pathway for tailoring the electronic environment to facilitate the accessibility of highly oxidized metal species for the rational design of efficient and cost-effective OER electrocatalysts.
- 22 December 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Reduced Graphene Oxide- and Triethanolamine-Decorated Nickel Oxide Electrocatalyst for Efficient Water/Saline Water Oxidation
The development of low-cost, highly efficient catalysts for the oxygen evolution reaction (OER) is one of the key steps for advancing renewable energy production. Increasing the density of high-valence metal species, coupled with rapid surface reconstruction, is a promising, but challenging design strategy for efficient OER catalysts. Herein, we report a facile electronic modulation approach for Ni oxide catalyst design (Ni/CP-TEA-GO), achieved by codecorating the surface with reduced graphene oxide (GO) and an N-group-containing ligand, triethanolamine (TEA), via a simple two-step electrodeposition process. The electrochemically reduced GO serves as an anchor site to couple the Ni sites and induces strong electronic interactions with the Ni sites, improving stability and promoting the formation of high-valence Ni species as active sites. Concurrently, the leaching of TEA further accelerates the generation of high-valence Ni species under the anodic potential. This functional surface modification approach is both cost-effective and scalable, distinguishing it from more complex or noble-metal-based strategies. The Ni/CP-TEA-GO exhibits outstanding OER performance, with a low overpotential of 230 mV at 10 mA·cm-2, rapid OER kinetics with a small Tafel slope of 31 mV·dec-1, and great long-term stability. Moreover, it achieves an overpotential of 360 mV to drive a current density of 50 mV·cm-2 for simulated alkaline seawater oxidation, exhibiting remarkable durability over a 100-h test. This work presents an effective and simple pathway for tailoring the electronic environment to facilitate the accessibility of highly oxidized metal species for the rational design of efficient and cost-effective OER electrocatalysts.
- 14 November 2024
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 24 (47) , 15085-15091
Revealing Epitaxial Deposition in Alkali Metal Batteries
Alkali metal batteries have high energy densities required to power future devices; however, uneven metal deposition is a critical barrier to achieving long lifespans. We have developed an elegant noncryogenic transmission electron microscopy method which has facilitated the first observations of epitaxial deposition in alkali metal batteries. Using this method, we have confirmed epitaxial interactions between (002) sodium crystallite planes and (01-11) planes in zinc current collectors. Such epitaxial interactions decrease nucleation energy barriers and promote even metal growth. This study offers fresh inspiration for the development of electron microscopy techniques tailored to electron-sensitive battery materials and sets a new agenda for the development of battery technologies.
- 14 November 2024
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 24 (47) , 15085-15091
Revealing Epitaxial Deposition in Alkali Metal Batteries
Alkali metal batteries have high energy densities required to power future devices; however, uneven metal deposition is a critical barrier to achieving long lifespans. We have developed an elegant noncryogenic transmission electron microscopy method which has facilitated the first observations of epitaxial deposition in alkali metal batteries. Using this method, we have confirmed epitaxial interactions between (002) sodium crystallite planes and (01-11) planes in zinc current collectors. Such epitaxial interactions decrease nucleation energy barriers and promote even metal growth. This study offers fresh inspiration for the development of electron microscopy techniques tailored to electron-sensitive battery materials and sets a new agenda for the development of battery technologies.
- Open Access
- 31 October 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (6)
Effect of nitrogen pressure on the fabrication of AlCrFeCoNiCu0.5 high entropy nitride thin films via cathodic arc deposition
In the past two decades, high entropy alloy (HEA) coatings have attracted great attention due to their superior mechanical properties, outstanding corrosion and oxidation resistance, and exceptionally high thermal stability. In comparison to HEA thin films, high entropy nitrides (HENs) exhibit higher mechanical strength and chemical inertness. In this work, AlCrFeCoNiCu0.5 HEA and HEN thin films were fabricated using a filtered cathodic arc. By regulating the deposition pressure from 0.0005 Pa (HEA thin film) to 0.05 Pa, the nitrogen concentration in each thin film was precisely controlled to tune the mechanical properties. Scanning transmission electron microscopy-energy dispersive spectroscopy revealed that the nitrogen concentration of the films was up to 21.2 at. % at the pressure of 0.05 Pa. The reduced effect of preferential sputtering increased aluminum concentration from 8.3 ± 1.5 to 12.9 ± 2.2 at. % as pressure increased up to 0.05 Pa. X-ray photoelectron spectroscopy further confirmed the formation of AlN and CrN at pressures of 0.01–0.05 Pa. The highest hardness and elastic modulus of the HEN film were 12.4 ± 0.6 and 347.3 ± 17.7 GPa, respectively, which were 84.8% and 131.4% higher than those of the HEA thin film.
- 31 October 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (6)
Open AccessEffect of nitrogen pressure on the fabrication of AlCrFeCoNiCu0.5 high entropy nitride thin films via cathodic arc deposition
In the past two decades, high entropy alloy (HEA) coatings have attracted great attention due to their superior mechanical properties, outstanding corrosion and oxidation resistance, and exceptionally high thermal stability. In comparison to HEA thin films, high entropy nitrides (HENs) exhibit higher mechanical strength and chemical inertness. In this work, AlCrFeCoNiCu0.5 HEA and HEN thin films were fabricated using a filtered cathodic arc. By regulating the deposition pressure from 0.0005 Pa (HEA thin film) to 0.05 Pa, the nitrogen concentration in each thin film was precisely controlled to tune the mechanical properties. Scanning transmission electron microscopy-energy dispersive spectroscopy revealed that the nitrogen concentration of the films was up to 21.2 at. % at the pressure of 0.05 Pa. The reduced effect of preferential sputtering increased aluminum concentration from 8.3 ± 1.5 to 12.9 ± 2.2 at. % as pressure increased up to 0.05 Pa. X-ray photoelectron spectroscopy further confirmed the formation of AlN and CrN at pressures of 0.01–0.05 Pa. The highest hardness and elastic modulus of the HEN film were 12.4 ± 0.6 and 347.3 ± 17.7 GPa, respectively, which were 84.8% and 131.4% higher than those of the HEA thin film.