Honglei Zhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Honglei Zhan has a total of 129 co-authors. Here are the top co-authors by number of shared publications:
- Kun Zhao
College of New Energy and Materials, China University of Petroleum, Beijing 102249, China
28 shared publications - Xinyang Miao
Key Laboratory of Oil and Gas Terahertz Spectroscopy and Photoelectric Detection, Petroleum and Chemical Industry Federation, China University of Petroleum, Beijing 102249, China
14 shared publications Wenzheng Yue
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing 102249, China
12 shared publicationsKun Zhao
10 shared publicationsRu Chen
9 shared publicationsXinyang Miao
8 shared publications
Latest Publications
- 11 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (33) , 24343-24348
Unraveling Oil-Content-Regulated Marangoni Flow Dynamics at Oil–Water Interfaces by In Situ Oblique-Incidence Reflectivity Difference
A critical challenge in understanding the Marangoni effect at oil–water interfaces lies in the lack of techniques that simultaneously provide high sensitivity, in situ real-time monitoring, and spatiotemporally synchronous characterization, which hinders the elucidation of the dynamic mechanisms and regulation principles of interfacial flows. To address this gap, we employed oblique-incidence reflectivity difference (OIRD) as a label-free optical method to investigate, in real time and in situ, the Marangoni flow dynamics in oil–water systems (oil phase: tridecane) with W/O ratios of 100:1, 100:2, and 100:3 over 0–500 s. By extracting oscillation features of the OIRD imaginary-part signal Im{Δp−Δs}, and conducting peak–valley analysis, amplitude calculation, and spreading velocity fitting together with spatial imaging, the regulatory role of oil content on interfacial Marangoni behavior was systematically revealed. The periodic oscillations of the OIRD signal sensitively capture fluid disturbances driven by interfacial tension gradients, and the flow intensity exhibits a significant negative correlation with oil content: lower oil content yields a larger interfacial tension gradient, resulting in more pronounced oscillation amplitude, faster initial spreading velocity, and a prolonged relaxation process. For the W/O = 100:1 system, OIRD spatial images at t = 50 s display regular concentric alternating bright and dark rings, and the transverse and longitudinal cross-sectional signals both exhibit orientation-independent periodic oscillations, suggesting that the interfacial fluctuation forms an isotropic periodic ripple structure that exhibits a suggestive spatiotemporal correspondence with the time-domain signals at this representative time point. This work establishes OIRD as a powerful tool for resolving the in situ dynamics of Marangoni flows and provides mechanistic insights into how oil content governs interfacial flow intensity and pattern formation.
- 11 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (33) , 24343-24348
Unraveling Oil-Content-Regulated Marangoni Flow Dynamics at Oil–Water Interfaces by In Situ Oblique-Incidence Reflectivity Difference
A critical challenge in understanding the Marangoni effect at oil–water interfaces lies in the lack of techniques that simultaneously provide high sensitivity, in situ real-time monitoring, and spatiotemporally synchronous characterization, which hinders the elucidation of the dynamic mechanisms and regulation principles of interfacial flows. To address this gap, we employed oblique-incidence reflectivity difference (OIRD) as a label-free optical method to investigate, in real time and in situ, the Marangoni flow dynamics in oil–water systems (oil phase: tridecane) with W/O ratios of 100:1, 100:2, and 100:3 over 0–500 s. By extracting oscillation features of the OIRD imaginary-part signal Im{Δp−Δs}, and conducting peak–valley analysis, amplitude calculation, and spreading velocity fitting together with spatial imaging, the regulatory role of oil content on interfacial Marangoni behavior was systematically revealed. The periodic oscillations of the OIRD signal sensitively capture fluid disturbances driven by interfacial tension gradients, and the flow intensity exhibits a significant negative correlation with oil content: lower oil content yields a larger interfacial tension gradient, resulting in more pronounced oscillation amplitude, faster initial spreading velocity, and a prolonged relaxation process. For the W/O = 100:1 system, OIRD spatial images at t = 50 s display regular concentric alternating bright and dark rings, and the transverse and longitudinal cross-sectional signals both exhibit orientation-independent periodic oscillations, suggesting that the interfacial fluctuation forms an isotropic periodic ripple structure that exhibits a suggestive spatiotemporal correspondence with the time-domain signals at this representative time point. This work establishes OIRD as a powerful tool for resolving the in situ dynamics of Marangoni flows and provides mechanistic insights into how oil content governs interfacial flow intensity and pattern formation.
- 2 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-7
In Situ Probing of Surfactant Micelles Behavior on the Surface/Interface: Oblique-Incidence Reflectivity Difference
Considering the significant role of surfactant-flooding in Enhanced Oil Recovery(EOR) for low-permeability and ultra-low permeability reservoirs, it is necessary to get insight into the dynamic mechanism of surfactant micelles behavior at gas-liquid interface. In this study, oblique-incidence reflectivity difference (OIRD) analysis is demonstrated to be a powerful tool for the in-situ analysis of surfactant micelles behavior. Based on the detection of cationic surfactant solutions, we develop a detailed model of molecular dynamic micellization process that it can be used to predict actual micellization and physical features. The results demonstrate a significant upward trend followed by a sharp decline in the OIRD signal as the CTAB concentration increases, which exactly reveals surfactant micelles mechanism including molecular migration and adsorption, pre-micellar generation, and micelle formation. More detailed characteristics of the surfactant micelles also can be inferred, which include not only the critical micelle concentration (CMC) but also the critical pre-micelle concentration(CPC). This work aid in further understanding the dynamic mechanisms underlying the adsorption and micellization processes of surfactant molecules at the gas-liquid interface on a molecular scale, which is helpful to the utilization of surfactant-flooding in enhanced oil recovery (EOR).
- 2 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-7
In Situ Probing of Surfactant Micelles Behavior on the Surface/Interface: Oblique-Incidence Reflectivity Difference
Considering the significant role of surfactant-flooding in Enhanced Oil Recovery(EOR) for low-permeability and ultra-low permeability reservoirs, it is necessary to get insight into the dynamic mechanism of surfactant micelles behavior at gas-liquid interface. In this study, oblique-incidence reflectivity difference (OIRD) analysis is demonstrated to be a powerful tool for the in-situ analysis of surfactant micelles behavior. Based on the detection of cationic surfactant solutions, we develop a detailed model of molecular dynamic micellization process that it can be used to predict actual micellization and physical features. The results demonstrate a significant upward trend followed by a sharp decline in the OIRD signal as the CTAB concentration increases, which exactly reveals surfactant micelles mechanism including molecular migration and adsorption, pre-micellar generation, and micelle formation. More detailed characteristics of the surfactant micelles also can be inferred, which include not only the critical micelle concentration (CMC) but also the critical pre-micelle concentration(CPC). This work aid in further understanding the dynamic mechanisms underlying the adsorption and micellization processes of surfactant molecules at the gas-liquid interface on a molecular scale, which is helpful to the utilization of surfactant-flooding in enhanced oil recovery (EOR).
- Open Access
- 1 March 2026
- Published by KEAI Publishing in Petroleum Science
- Vol. 23 (3) , 1459-1468
Charge-structure synergy in reservoir wettability reversal: Investigating with an integrated optical-multiscale framework
- 1 March 2026
- Published by KEAI Publishing in Petroleum Science
- Vol. 23 (3) , 1459-1468
Open AccessCharge-structure synergy in reservoir wettability reversal: Investigating with an integrated optical-multiscale framework
- 16 November 2025
- Published by Elsevier in Analytica Chimica Acta
- Vol. 1383, 344899
Machine learning-assisted rapid screening of oil types on microfluidic thread-based analytical devices (μTADs)
- 16 November 2025
- Published by Elsevier in Analytica Chimica Acta
- Vol. 1383, 344899
Machine learning-assisted rapid screening of oil types on microfluidic thread-based analytical devices (μTADs)
- 1 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-9
Electrically Tunable Laser-Induced Voltage of Coffee
In this work laser-induced voltage (LIV) of a selected commercial coffee was studied. We focused on the electrically tunable LIV response under a KrF pulsed laser irradiation. The typical LIV transient consisted of three components of fast rise within 40 ns, slower rise from 0.04 to 100 μs and attenuation after 100 μs. The response process was fitted by the sum of the three exponential functions, which was agreement with the measured LIV data. The time dependences of LIV were tuned strongly by bias voltage and laser energy. Higher laser energy and bias voltage enhanced LIV, in contrast the rise time and full width at half maximum were negatively correlated with laser energy and bias voltage. The LIV decay time was shortened significantly by reducing the adjustable resister parallel to coffee sample. When an impendence of 10 Y was applied the LIV trace was almost triangular and symmetrical, and the response time was completely limited by the laser pulse duration. Furthermore, the LIV response increases with laser energy.
- 1 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-9
Electrically Tunable Laser-Induced Voltage of Coffee
In this work laser-induced voltage (LIV) of a selected commercial coffee was studied. We focused on the electrically tunable LIV response under a KrF pulsed laser irradiation. The typical LIV transient consisted of three components of fast rise within 40 ns, slower rise from 0.04 to 100 μs and attenuation after 100 μs. The response process was fitted by the sum of the three exponential functions, which was agreement with the measured LIV data. The time dependences of LIV were tuned strongly by bias voltage and laser energy. Higher laser energy and bias voltage enhanced LIV, in contrast the rise time and full width at half maximum were negatively correlated with laser energy and bias voltage. The LIV decay time was shortened significantly by reducing the adjustable resister parallel to coffee sample. When an impendence of 10 Y was applied the LIV trace was almost triangular and symmetrical, and the response time was completely limited by the laser pulse duration. Furthermore, the LIV response increases with laser energy.
- 2 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (12) , 12752-12758
Tunable Laser-Induced Voltage of Sugar for Ultrafast Ultraviolet Laser Pulse Detection
A low cost rapid process for deep ultraviolet (UV) laser pulse detection has been proposed and experimentally realized by table sugars (such as fine white sugar (FS), granulated sugar (GS), and brown sugar (BS)). A systematic study about laser-induced voltage (LIV) under a KrF pulsed laser irradiation was presented by tuning the applied bias (V b ), laser energy (E in ), and shunting resistance (R) parallel to sample. Higher E in enhanced LIV peak magnitude (V p ), whereas the rise time and full width at half maximum were negatively correlated with E in . FS showed higher LIV than GS due to the smaller particle size of FS than that of GS. The LIV response trace consisted of three components of fast rise, slower rise, and attenuation, which was fitted well by the sum of the three exponential functions. Furthermore, the LIV response time was shortened significantly by reducing the R. When a fixed R of 14.7 Ω was applied the LIV trace displayed a l0%-90% rising time of ~ 12.2 ns and a l0%-90% falling time of ~ 23.5 ns. The response time was completely limited by the laser pulse duration, indicating the waveform of laser pulse was detected. In addition the specific detectivity D* over V b (D*/V b ) of FS is estimated to be 2.67 × 10 7 m 1/2 ∙J -3/2 at lower E in (< 20 mJ), which was 38% and 84% higher than that of GS and BS. Our work provided a simple, low-cost, and fast method to detect a deep UV laser pulse with table sugar as the detector material.
- 2 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (12) , 12752-12758
Tunable Laser-Induced Voltage of Sugar for Ultrafast Ultraviolet Laser Pulse Detection
A low cost rapid process for deep ultraviolet (UV) laser pulse detection has been proposed and experimentally realized by table sugars (such as fine white sugar (FS), granulated sugar (GS), and brown sugar (BS)). A systematic study about laser-induced voltage (LIV) under a KrF pulsed laser irradiation was presented by tuning the applied bias (V b ), laser energy (E in ), and shunting resistance (R) parallel to sample. Higher E in enhanced LIV peak magnitude (V p ), whereas the rise time and full width at half maximum were negatively correlated with E in . FS showed higher LIV than GS due to the smaller particle size of FS than that of GS. The LIV response trace consisted of three components of fast rise, slower rise, and attenuation, which was fitted well by the sum of the three exponential functions. Furthermore, the LIV response time was shortened significantly by reducing the R. When a fixed R of 14.7 Ω was applied the LIV trace displayed a l0%-90% rising time of ~ 12.2 ns and a l0%-90% falling time of ~ 23.5 ns. The response time was completely limited by the laser pulse duration, indicating the waveform of laser pulse was detected. In addition the specific detectivity D* over V b (D*/V b ) of FS is estimated to be 2.67 × 10 7 m 1/2 ∙J -3/2 at lower E in (< 20 mJ), which was 38% and 84% higher than that of GS and BS. Our work provided a simple, low-cost, and fast method to detect a deep UV laser pulse with table sugar as the detector material.
- 22 November 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (4) , 1-13
A Photoconductance Mechanism for Oil Shale Pyrolysis Process Detection
Kerogen in oil shale plays a crucial part in the shale oil and gas generation. Here, photoconductive measurement was used to evaluate the decomposition process of Huadian oil shale. The photoconductivity of the semi-coke is a clear indicator of different pyrolysis stages, including moisture evaporation, primary pyrolysis of kerogen, decomposition of asphalt monomer, and mineral decomposition. Furthermore, the distribution model of electrical resistance (R) and photoconductance (ΔI) for Huadian oil shale is plotted, indicating an inverse proportion between R and ΔI. We believe that the photoconductive measurement will be a valuable means for the nondestructive characterization of oil shale pyrolysis, which is helpful to optimize the comprehensive utilization of this unconventional resource.
- 22 November 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (4) , 1-13
A Photoconductance Mechanism for Oil Shale Pyrolysis Process Detection
Kerogen in oil shale plays a crucial part in the shale oil and gas generation. Here, photoconductive measurement was used to evaluate the decomposition process of Huadian oil shale. The photoconductivity of the semi-coke is a clear indicator of different pyrolysis stages, including moisture evaporation, primary pyrolysis of kerogen, decomposition of asphalt monomer, and mineral decomposition. Furthermore, the distribution model of electrical resistance (R) and photoconductance (ΔI) for Huadian oil shale is plotted, indicating an inverse proportion between R and ΔI. We believe that the photoconductive measurement will be a valuable means for the nondestructive characterization of oil shale pyrolysis, which is helpful to optimize the comprehensive utilization of this unconventional resource.
- 28 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-7
Optical Detection for the Adsorption Kinetics of Surfactant Solutions on the Surface/Interface: Oblique-Incidence Reflectivity Difference Investigation
The interaction of interfacial molecules was a hot issue in many fields, such as petroleum: the adsorption kinetics process of surfactant molecules on the interface was the key to reduce the dynamic interfacial tension and enhance oil recovery. Since the aggregation behavior of surfactant molecules on the water surface would lead to changes in the dielectric properties of the surface layer, we applied a dielectric detection technology with a vertical resolution of nanometer precision, oblique-incidence reflectivity difference (OIRD) technology, to study the adsorption kinetics of surfactant molecules on the water surface in this article. According to the test results, we established a model of molecular dynamic adsorption and explained its mechanism. This dynamic process could be divided into three stages: micelles dissociated in bulk water, molecules diffused to the subsurface layer, and molecules broke through the adsorption barrier and adsorbed on the water surface. Among them, the diffusion process was in accordance with Fick’s second law, and the process of surfactant molecules being adsorbed from the subsurface to the surface can be described by the Arrhenius formula. This work was not only applicable to the petroleum field to understand the essence of surfactant reducing surface tension but also to help investigate the subject of molecular behavior at the liquid–liquid or gas–liquid interface in other fields.
- 28 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-7
Optical Detection for the Adsorption Kinetics of Surfactant Solutions on the Surface/Interface: Oblique-Incidence Reflectivity Difference Investigation
The interaction of interfacial molecules was a hot issue in many fields, such as petroleum: the adsorption kinetics process of surfactant molecules on the interface was the key to reduce the dynamic interfacial tension and enhance oil recovery. Since the aggregation behavior of surfactant molecules on the water surface would lead to changes in the dielectric properties of the surface layer, we applied a dielectric detection technology with a vertical resolution of nanometer precision, oblique-incidence reflectivity difference (OIRD) technology, to study the adsorption kinetics of surfactant molecules on the water surface in this article. According to the test results, we established a model of molecular dynamic adsorption and explained its mechanism. This dynamic process could be divided into three stages: micelles dissociated in bulk water, molecules diffused to the subsurface layer, and molecules broke through the adsorption barrier and adsorbed on the water surface. Among them, the diffusion process was in accordance with Fick’s second law, and the process of surfactant molecules being adsorbed from the subsurface to the surface can be described by the Arrhenius formula. This work was not only applicable to the petroleum field to understand the essence of surfactant reducing surface tension but also to help investigate the subject of molecular behavior at the liquid–liquid or gas–liquid interface in other fields.