Qingyang Meng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qingyang Meng has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Hongtao Zheng
College of Power and Energy Engineering, Harbin Engineering University , 145 Nantong Street, Harbin 150001, China
2 shared publications - Huangwei Zhang
National University of Singapore
2 shared publications - Shangpeng Li
Department of Mechanical Engineering, National University of Singapore 1 , 9 Engineering Drive 1, 117576
2 shared publications Zijun Wang
2 shared publicationsChihyung Wen
The Hong Kong Polytechnic University
1 shared publication- Guangpu Lv
College of Power and Energy Engineering, Harbin Engineering University, Harbin, China
1 shared publication
Latest Publications
- 5 February 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (2)
Thermodynamic critical characterization and droplet dynamics in spray detonations
- 5 February 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (2)
Thermodynamic critical characterization and droplet dynamics in spray detonations
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Simulations of two-phase methane/oxygen rotating detonation wave at cryogenic condition
This paper numerically investigates rotating detonation waves in a gaseous methane/cryogenic liquid oxygen mixture using a non-premixed injection pattern. Distinct differences are observed between the liquid-oxygen detonation engine and traditional liquid-fueled detonation systems: (1) the rotating detonation wave exhibits a strong propensity to form a counter-rotating mode at near-stoichiometric conditions, and (2) a considerable parasitic flame anchors near the inlet, reducing the detonation fraction. Both the counter-rotating mode, characterized by the coexistence of counter-propagating primary and secondary shocks, and the one-wave mode are observed; the specific mode depends on the initial oxygen droplet diameter and the global equivalence ratio. Significant local explosions occur near oxygen droplets immediately behind the leading shock, inducing numerous retrograde shocklets. These shocklets couple with the parasitic flame in the vicinity of the oxygen cluster, facilitating the formation of a secondary shock. Increased gaseous methane mass flow rate (e.g., ϕ = 2.0) or decreased global reactivity (e.g., ϕ = 0.25) reduces the secondary wave strength, resulting in a dominant one-wave operating mode. In the counter-rotating mode, the presence of secondary shocks substantially decreases the total pressure gain due to multiple shock collisions. The maximum mean thrust is observed at ϕ = 2.0, while the minimum is found at ϕ = 0.25. However, variations in the methane mass flow rate lead to an inverse trend in specific impulse. Stable propulsive performance is found in the one-wave mode compared to the counter-rotating mode.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Simulations of two-phase methane/oxygen rotating detonation wave at cryogenic condition
This paper numerically investigates rotating detonation waves in a gaseous methane/cryogenic liquid oxygen mixture using a non-premixed injection pattern. Distinct differences are observed between the liquid-oxygen detonation engine and traditional liquid-fueled detonation systems: (1) the rotating detonation wave exhibits a strong propensity to form a counter-rotating mode at near-stoichiometric conditions, and (2) a considerable parasitic flame anchors near the inlet, reducing the detonation fraction. Both the counter-rotating mode, characterized by the coexistence of counter-propagating primary and secondary shocks, and the one-wave mode are observed; the specific mode depends on the initial oxygen droplet diameter and the global equivalence ratio. Significant local explosions occur near oxygen droplets immediately behind the leading shock, inducing numerous retrograde shocklets. These shocklets couple with the parasitic flame in the vicinity of the oxygen cluster, facilitating the formation of a secondary shock. Increased gaseous methane mass flow rate (e.g., ϕ = 2.0) or decreased global reactivity (e.g., ϕ = 0.25) reduces the secondary wave strength, resulting in a dominant one-wave operating mode. In the counter-rotating mode, the presence of secondary shocks substantially decreases the total pressure gain due to multiple shock collisions. The maximum mean thrust is observed at ϕ = 2.0, while the minimum is found at ϕ = 0.25. However, variations in the methane mass flow rate lead to an inverse trend in specific impulse. Stable propulsive performance is found in the one-wave mode compared to the counter-rotating mode.
- 1 May 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (5)
On the direct initiation in n-heptane mists considering droplet fragmentation
In this paper, direct initiated detonation with various initial energy depositions and droplet diameters in a one-dimensional n-heptane/oxygen/nitrogen heterogeneous system is simulated. Detonation evolution, frontal structure, and fuel droplet behavior are investigated. For a stoichiometric mixture with d0 = 5 μm, the critical initiation energy is around 1.6 × 105 J/m2 with no evidence of non-uniqueness. Initiation energy is crucial to activate the reaction O2 + H = OH + O, significantly contributing to OH production and sustaining the detonation. For a self-sustained detonation, initiation energy has a marginal influence on the variations of induction zone length, which is primarily determined by the initial droplet diameter. As droplet size increases, extended induction zone lengths with pronounced fluctuations are seen because of the increased breakup and evaporation time. Elevated Weber number is found both in the vicinity of the leading shock and reaction front, caused by large gas–droplet velocity differences and the low surface tension at the boiling point, respectively. Critical droplet in post-detonation region is found, which leads to the flash vaporization despite the droplet size is still large and yields localized high equivalence ratio and elevated heat release rate, accompanied by amplified shock.
- 1 May 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (5)
On the direct initiation in n-heptane mists considering droplet fragmentation
In this paper, direct initiated detonation with various initial energy depositions and droplet diameters in a one-dimensional n-heptane/oxygen/nitrogen heterogeneous system is simulated. Detonation evolution, frontal structure, and fuel droplet behavior are investigated. For a stoichiometric mixture with d0 = 5 μm, the critical initiation energy is around 1.6 × 105 J/m2 with no evidence of non-uniqueness. Initiation energy is crucial to activate the reaction O2 + H = OH + O, significantly contributing to OH production and sustaining the detonation. For a self-sustained detonation, initiation energy has a marginal influence on the variations of induction zone length, which is primarily determined by the initial droplet diameter. As droplet size increases, extended induction zone lengths with pronounced fluctuations are seen because of the increased breakup and evaporation time. Elevated Weber number is found both in the vicinity of the leading shock and reaction front, caused by large gas–droplet velocity differences and the low surface tension at the boiling point, respectively. Critical droplet in post-detonation region is found, which leads to the flash vaporization despite the droplet size is still large and yields localized high equivalence ratio and elevated heat release rate, accompanied by amplified shock.
- Open Access
- 8 March 2025
- Published by Elsevier in Combustion and Flame
- Vol. 275
Detonative wavelets in quasi-detonations with fine coal char particles
- 8 March 2025
- Published by Elsevier in Combustion and Flame
- Vol. 275
Open AccessDetonative wavelets in quasi-detonations with fine coal char particles
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Effects of total temperature and equivalence ratio on n-decane/air two-phase rotating detonation wave
The Eulerian–Lagrangian method is used to conduct the numerical simulation of the non-premixed two-phase rotating detonation wave (RDW) fueled by n-decane/air. The stratified spray detonation transient phenomena, as well as the effects of total temperature (850, 900, 1000 K) and equivalence ratio (0.5, 0.7, 1.0) on the RDW dynamics and propagation characteristics are discussed in detail. The results indicate that the velocity difference caused by separate injection of fuel and air generates the low-temperature zone behind the oblique shock wave, which hinders the direct contact between the droplets and the detonation products. Droplets in the refilled zone are broken by the shear effect and evaporate in high total temperature air, forming the stratified distribution structure of droplets and vapor. In addition, the coupling–decoupling–recoupling dynamic mechanism is observed between the leading shock front and the heat release zone, which leads to the local decoupling of RDW during the propagation. Moreover, the spatial variation of high-pressure zones at the leading shock front leads to multiple leading shock fronts and transverse pressure waves. It is revealed that the increase in total temperature broadens the lower boundary of equivalence ratio to obtain two-phase RDW. RDW velocity and velocity deficit are insensitive to the total temperature in the considered parameter range. However, the increase in the total equivalence ratio not only improves the mean velocity significantly but also enlarges the velocity deficit. With the increasing total temperature and equivalence ratio, the stability of pressure becomes worse. Furthermore, the stability of velocity declines with the increasing equivalence ratio at the total temperature of 1000 K.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Effects of total temperature and equivalence ratio on n-decane/air two-phase rotating detonation wave
The Eulerian–Lagrangian method is used to conduct the numerical simulation of the non-premixed two-phase rotating detonation wave (RDW) fueled by n-decane/air. The stratified spray detonation transient phenomena, as well as the effects of total temperature (850, 900, 1000 K) and equivalence ratio (0.5, 0.7, 1.0) on the RDW dynamics and propagation characteristics are discussed in detail. The results indicate that the velocity difference caused by separate injection of fuel and air generates the low-temperature zone behind the oblique shock wave, which hinders the direct contact between the droplets and the detonation products. Droplets in the refilled zone are broken by the shear effect and evaporate in high total temperature air, forming the stratified distribution structure of droplets and vapor. In addition, the coupling–decoupling–recoupling dynamic mechanism is observed between the leading shock front and the heat release zone, which leads to the local decoupling of RDW during the propagation. Moreover, the spatial variation of high-pressure zones at the leading shock front leads to multiple leading shock fronts and transverse pressure waves. It is revealed that the increase in total temperature broadens the lower boundary of equivalence ratio to obtain two-phase RDW. RDW velocity and velocity deficit are insensitive to the total temperature in the considered parameter range. However, the increase in the total equivalence ratio not only improves the mean velocity significantly but also enlarges the velocity deficit. With the increasing total temperature and equivalence ratio, the stability of pressure becomes worse. Furthermore, the stability of velocity declines with the increasing equivalence ratio at the total temperature of 1000 K.
- 1 September 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (9)
Numerical modeling and suppression of combustion instabilities in a partially premixed combustor
To suppress the combustion instabilities faced in the lean premixed combustion, the impacts of swirler hub configurations on combustion instabilities under elevated pressure are investigated using large eddy simulation combined with a flamelet generation manifold model. Good agreement between the numerical predictions and experimental data is achieved. The flow fields of the combustors with three distinct swirler configurations are simulated: prototype, swirler with lobes on the hub of pilot stage, and with lobes on the hub of the first main stage. Furthermore, dynamic mode decomposition (DMD) is used to extract the dynamic characteristics, and a flame transfer function (FTF) is employed to characterize the fluctuation characteristics. The results show that the prototype combustor demonstrates a coupled fluctuation between flow and heat release. Influenced by the precessing vortex core (PVC), the flame angle varies between 70° and 90° and the first DMD modes of axial velocity, temperature, and heat release rate are all at a frequency of 470 Hz. The lobes on the hub of the pilot stage suppress the formation of PVC, making the combustion very stable. The flame angle remains constant at 80°, and the gain of FTF is lower than 1. However, adding lobes to the first main stage makes the combustion extremely unstable. The flow field structure undergoes drastic changes, mimicking a “breathe” process. The flame surface is highly distorted, and flashback phenomena occur.
- 1 September 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (9)
Numerical modeling and suppression of combustion instabilities in a partially premixed combustor
To suppress the combustion instabilities faced in the lean premixed combustion, the impacts of swirler hub configurations on combustion instabilities under elevated pressure are investigated using large eddy simulation combined with a flamelet generation manifold model. Good agreement between the numerical predictions and experimental data is achieved. The flow fields of the combustors with three distinct swirler configurations are simulated: prototype, swirler with lobes on the hub of pilot stage, and with lobes on the hub of the first main stage. Furthermore, dynamic mode decomposition (DMD) is used to extract the dynamic characteristics, and a flame transfer function (FTF) is employed to characterize the fluctuation characteristics. The results show that the prototype combustor demonstrates a coupled fluctuation between flow and heat release. Influenced by the precessing vortex core (PVC), the flame angle varies between 70° and 90° and the first DMD modes of axial velocity, temperature, and heat release rate are all at a frequency of 470 Hz. The lobes on the hub of the pilot stage suppress the formation of PVC, making the combustion very stable. The flame angle remains constant at 80°, and the gain of FTF is lower than 1. However, adding lobes to the first main stage makes the combustion extremely unstable. The flow field structure undergoes drastic changes, mimicking a “breathe” process. The flame surface is highly distorted, and flashback phenomena occur.
- Open Access
- 1 December 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (12)
Detailed simulations of one-dimensional detonation propagation in dilute n-heptane spray and air mixtures
One-dimensional numerical simulations based on the hybrid Eulerian–Lagrangian approach are performed to investigate detonation dynamics in two-phase gas-droplet n-heptane/air mixtures with and without liquid fuel pre-vaporization. The reactive Navier–Stokes equations considering the two-way coupling for interphase exchanges of mass, momentum, energy, and species are solved with a skeletal mechanism consisting of 44 species and 112 reactions. The effects of n-heptane droplet diameter and equivalence ratio (ER) on average detonation speed and mode are studied. For pre-vaporization cases, the average detonation speed first decreases and then increases with droplet diameter ranging from 2.5 to 40 μm, which is minimum at 7.5–10 μm due to the competition between fuel vapor addition and droplet evaporative heat absorption. However, the average speed increases monotonically as the droplet ER increases from 0.2 to 1.2. A further increase in the droplet ER (e.g., 2.4) would lead to detonation suppression in the presence of large droplets (e.g., above 30 μm). The detonation is fully quenched when the droplet ER is 3.2. Similar observations are also made for the pure sprayed cases without n-heptane pre-vaporization, where the average speed increases rapidly for droplet ER of 0.2–0.8 and slowly for ER of 0.8–1.6. Various detonation modes are observed with respect to droplet diameter and equivalence ratio, either with or without fuel pre-vaporization. Generally, the pure sprayed cases show more irregular behaviors in detonation propagation. The laden droplets provide a new approach to control the intrinsically unstable or highly irregular behaviors of pure gas or pure sprayed detonations. The finite, small disturbances from the spatially non-uniform droplets, and enrichment from the droplet evaporative mass addition, are two essential mechanisms for the mitigation of the pulsating detonation.
- 1 December 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (12)
Open AccessDetailed simulations of one-dimensional detonation propagation in dilute n-heptane spray and air mixtures
One-dimensional numerical simulations based on the hybrid Eulerian–Lagrangian approach are performed to investigate detonation dynamics in two-phase gas-droplet n-heptane/air mixtures with and without liquid fuel pre-vaporization. The reactive Navier–Stokes equations considering the two-way coupling for interphase exchanges of mass, momentum, energy, and species are solved with a skeletal mechanism consisting of 44 species and 112 reactions. The effects of n-heptane droplet diameter and equivalence ratio (ER) on average detonation speed and mode are studied. For pre-vaporization cases, the average detonation speed first decreases and then increases with droplet diameter ranging from 2.5 to 40 μm, which is minimum at 7.5–10 μm due to the competition between fuel vapor addition and droplet evaporative heat absorption. However, the average speed increases monotonically as the droplet ER increases from 0.2 to 1.2. A further increase in the droplet ER (e.g., 2.4) would lead to detonation suppression in the presence of large droplets (e.g., above 30 μm). The detonation is fully quenched when the droplet ER is 3.2. Similar observations are also made for the pure sprayed cases without n-heptane pre-vaporization, where the average speed increases rapidly for droplet ER of 0.2–0.8 and slowly for ER of 0.8–1.6. Various detonation modes are observed with respect to droplet diameter and equivalence ratio, either with or without fuel pre-vaporization. Generally, the pure sprayed cases show more irregular behaviors in detonation propagation. The laden droplets provide a new approach to control the intrinsically unstable or highly irregular behaviors of pure gas or pure sprayed detonations. The finite, small disturbances from the spatially non-uniform droplets, and enrichment from the droplet evaporative mass addition, are two essential mechanisms for the mitigation of the pulsating detonation.
- 1 February 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (2)
Modeling particle collisions in moderately dense curtain impacted by an incident shock wave
The interactions between an incident shock and a moderately dense particle curtain are simulated with the Eulerian–Lagrangian method. A customized solver based on OpenFOAM is extended with an improved drag model and collision model and then validated against two benchmark experiments. The results show that the collision model has a limited impact on curtain morphology compared with the improved drag model. In this work, parametric studies are performed considering different particle sizes, volume fractions, and curtain thicknesses. Smaller particle sizes and larger volume fractions lead to stronger reflected shock and weaker transmitted shock. Attention is paid to the particle collision effects on the curtain evolution behaviors. According to our results, for the mono-dispersed particle curtain, the collision effects on curtain front behaviors are small, even when the initial particle volume fraction is as high as 20%. This is due to the positive velocity gradient across the curtain after the shock wave passage, leading to the faster motion of downstream particles than the upstream ones, and hence, no collision occurs. For the bi-dispersed particle curtain, the collision effects become important in the mixing region of different-size particles. Collisions decelerate small particles while accelerating large ones and cause velocity scattering. Moreover, increasing the bi-dispersed curtain thickness leads to multiple collision force peaks, which is the result of the delayed separation of different particle groups. Our results indicate that the collision model may be unnecessary to predict curtain fronts in mono-dispersed particles, but in bi-dispersed particles, the collision effects are important and, therefore, must be modeled.
- 1 February 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (2)
Modeling particle collisions in moderately dense curtain impacted by an incident shock wave
The interactions between an incident shock and a moderately dense particle curtain are simulated with the Eulerian–Lagrangian method. A customized solver based on OpenFOAM is extended with an improved drag model and collision model and then validated against two benchmark experiments. The results show that the collision model has a limited impact on curtain morphology compared with the improved drag model. In this work, parametric studies are performed considering different particle sizes, volume fractions, and curtain thicknesses. Smaller particle sizes and larger volume fractions lead to stronger reflected shock and weaker transmitted shock. Attention is paid to the particle collision effects on the curtain evolution behaviors. According to our results, for the mono-dispersed particle curtain, the collision effects on curtain front behaviors are small, even when the initial particle volume fraction is as high as 20%. This is due to the positive velocity gradient across the curtain after the shock wave passage, leading to the faster motion of downstream particles than the upstream ones, and hence, no collision occurs. For the bi-dispersed particle curtain, the collision effects become important in the mixing region of different-size particles. Collisions decelerate small particles while accelerating large ones and cause velocity scattering. Moreover, increasing the bi-dispersed curtain thickness leads to multiple collision force peaks, which is the result of the delayed separation of different particle groups. Our results indicate that the collision model may be unnecessary to predict curtain fronts in mono-dispersed particles, but in bi-dispersed particles, the collision effects are important and, therefore, must be modeled.