Agnieszka Marasek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Agnieszka Marasek has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Ali Abouais
Institute of Physics, Faculty of Physics, Astronomy and Informatics, Nicolaus Copernicus University in Toruń, ul. Grudziadzka 5, 87-100 Toruń, Poland
1 shared publication - Daniel Kamiński
Department of Organic Chemistry and Crystal Chemistry, Faculty of Chemistry, Maria Curie-Skłodowska University, 2/508 Maria Curie-Skłodowska Sq., 20-031 Lublin, Poland
1 shared publication - Jacek Zakrzewski
Institute of Physics, Nicolaus Copernicus University, ul. Grudziadzka 5/7, 87-100 Toruń, Poland
1 shared publication - Karol Strzałkowski
Institute of Physics, Faculty of Physics, Astronomy and Informatics, Nicolaus Copernicus University, Grudziądzka 5, 87-100 Toruń, Poland
1 shared publication - Mohammed Boumhamdi
Institute of Physics, Nicolaus Copernicus University, ul. Grudziadzka 5/7, 87-100 Toruń, Poland
1 shared publication
Latest Publications
- Open Access
- 7 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2113
Photothermal Determination of the Surface Treatment of Cd1-xBexTe Mixed Crystals
Cd1−xBexTe, a new material with potential for X-ray and γ-ray detectors, was analyzed by photothermal piezoelectric spectroscopy. The samples were tested depending on beryllium content and surface preparation. The main aim of the measurements was to extract the energy gap values, which were found for x = 0.01, 0.03, 0.05, and 0.1. It was shown that mechanical (polishing) and chemical (etching) treatment strongly influenced the amplitude and phase spectra of CdBeTe crystals. Piezoelectric spectroscopy allowed for comparing the quality of preparation of both surfaces for a single sample. The sub-surface damaged layer that was created as a result of surface processing had different thermal parameters than the bulk part of the sample. It was responsible for the additional peaks in the amplitude spectrum and changes in the phase spectrum of the photothermal signal. Two different methods of sample etching were analyzed. One completely quenched the signal, and the other did not eliminate the defects present on the surface after the cutting process. The article presents the preliminary interpretation of experimental data using the modified Blonskij model.
- 7 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2113
Open AccessPhotothermal Determination of the Surface Treatment of Cd1-xBexTe Mixed Crystals
Cd1−xBexTe, a new material with potential for X-ray and γ-ray detectors, was analyzed by photothermal piezoelectric spectroscopy. The samples were tested depending on beryllium content and surface preparation. The main aim of the measurements was to extract the energy gap values, which were found for x = 0.01, 0.03, 0.05, and 0.1. It was shown that mechanical (polishing) and chemical (etching) treatment strongly influenced the amplitude and phase spectra of CdBeTe crystals. Piezoelectric spectroscopy allowed for comparing the quality of preparation of both surfaces for a single sample. The sub-surface damaged layer that was created as a result of surface processing had different thermal parameters than the bulk part of the sample. It was responsible for the additional peaks in the amplitude spectrum and changes in the phase spectrum of the photothermal signal. Two different methods of sample etching were analyzed. One completely quenched the signal, and the other did not eliminate the defects present on the surface after the cutting process. The article presents the preliminary interpretation of experimental data using the modified Blonskij model.