SMSaleh Abd El-Aleem Mohamed

Saleh Abd El-Aleem Mohamed

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Saleh Abd El-Aleem Mohamed has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Utilization of Foamed Glass as an Effective Adsorbent for Methylene Blue: Insights into Physicochemical Properties and Theoretical Treatment

    by Hussein Al-Kroom, Hamdy A. Abdel-Gawwad, Mohamed Abd Elrahman, Saleh Abdel-Aleem, Mohamed Saad Ahmed, Yasser F. Salama, Saleh Qaysi, Mateusz Techman, Moaaz K. Seliem, Osama Youssf

    This study reports a potential approach for the valorization of glass waste (GW) that is mainly composed of amorphous silica to prepare lightweight foamed glass (FG). The preparation of FG was achieved by mixing sodium hydroxide with GW powder followed by sintering at a temperature of 800 °C. As-synthesized FG was characterized and applied as an effective adsorbent for the removal of hazardous organic water contaminants, in particular, methylene blue (MB) dye. FG exhibited porosity of 91%, bulk density of 0.65 g/cm3, compressive strength of 4 MPa, and thermal conductivity of 0.27 W/m·K. Theoretical treatment indicated that a monolayer model with one energy site was the best in fitting the removal of MB molecules. The number of MB molecules per active site (n) ranged from 2.20 to 1.70, suggesting vertical orientation and a multi-molecular adsorption mechanism. The density of FG receptor sites (DM) increased with the temperature, and this parameter played a vital role in the adsorption process. The adsorption capacity (Qsat) increased from 255.11 to 305.58 mg/g, which signifies endothermic interactions. MB adsorption on FG was controlled by physical forces such as electrostatic interactions (i.e., the adsorption energies were <20 kJ/mol). The results of this study prove the feasibility of glass waste as an effective and low-cost adsorbent for water remediation.


  • Open Access

    Chemical and Engineering Properties of Blended Cement Containing Micro- and Nano-silica

    by Hamdy El-Didamony Ahmed, Berry Abd El-Ghani Sabrah, Saleh Abd El-Aleem Mohamed, Nashwa Mohamed Mostafa

    Nano-technology (NT) and nano-materials (NMs) has attracted considerable scientific attention, due to the new potential uses of nano-particles (NPs), which can change the concrete world. There is a great interest in replacing a long time used materials in concrete structure by NMs to improve the different properties of concrete. In this study, the hydration characteristics and microstructure of cement pastes and mortars with and without nano-silica (NS) were studied. Blended cement mix containing 10 mass, % silica fume (SF) was prepared, then the cement mix was partially replaced by NS up 1.5 mass, %. The results show that, NS increases the water of consistency and final setting time The values of chemically combined water, free lime, bulk density and compressive strength prove that, NS up to 1% seems to be an effective mineral additive for blending with OPC to improve its chemical and engineering properties. This is mainly attributed to that; NS behaves not only as filler to improve microstructure, but also as pozzolanic material (PZM). The formation of more hydrated silicates in presence of NS was confirmed by XRD, DTA, IR and SEM examinations. At 1.5 mass, % NS, the density and strength are reduced but still higher than those of 0.0 and 0.5% NS. Also, the results indicate that, the substitution of blended cement mix (OPC+10% SF) with 1 mass, % NS gives a reasonable hydration characteristics and improved engineering properties more than those of 0.0 and 0.5% NS at all hydration ages up to 90 days. Therefore, this level of NS is suggested to be the most suitable replacement level.


  • Open Access

    The Effect of Microsilica and Aluminum Metal Powder on the Densification Parameters, Mechanical Properties and Microstructure of Alumina–Mullite Ceramic Composites

    by M. M. S. Wahsh, H. E. H. Sadek, S. Abd El-Aleem, H. H. M. Darweesh

    Microsilica, or silica fume, is an amorphous type of silica mostly collected as byproduct of the silicon and ferro-silicon alloy production. In this work, low shrinkage alumina-mullite ceramic composites were prepared from mixtures of calcined alumina, silica fume and aluminum metal powder and sintered at 1550oC for 2 hrs. The influence of silica fume and aluminum powder on the densification parameter, in situ mullite formed and mechanical properties of sintered samples were studied. The phase composition and the microstructural evolution of the sintered samples were also investigated. The results showed that, silica fume enhances the mechanical properties of sintered samples, while the aluminum powder improves the mullite formation process. Ultra low shrinkage (close to zero), and good mechanical properties (CCS ≈ 70 MPa) of alumina-mullite ceramic composites were achieved. Alumina-mullite ceramic composites are considered a promising material for high temperature applications.


  • Open Access

    Impact of Alkali Concentration and Metakaolin Content on Accelerated Ageing of Egyptian Slag

    by Hamdy Abd El-Aziz Abdel Gawwad, Hesham Mohamed Khater, Saleh Abd El-Aleem Mohamed

    The present work aims to study the coupled effect of alkali concentration and metakaolin (MK) on the resistivity of ground granulated blast-furnace slag (GGBFS) to strength regression during ageing. GGBFS was activated by 6 and 10 wt., % containing mixture of sodium hydroxide (SH) and liquid sodium silicate (LSS) at a ratio of 1:1, respectively (namely GGBFS6 and GGBFS10). On the other hand, GGBFS10 was replaced by 10, 20, 30, 40 and 50 wt., % of MK, respectively. All hardened specimens were cured in 100% relative humidity (RH) at 37 ± 2°C for 28 days (zero time) then, aged at 95°C for 56 days. Experimental results showed that, the pH value of alkali activated samples (AAS) decreased as the amount of MK increased. Also, the pH of AAS derived from GGBFS10 was higher than that of GGBFS6. The strength regression resistivity (SRR) during accelerated ageing enhanced with the decrease of alkali concentration. The compressive strength for different investigated mixes was evaluated. Also, some selected hydration products were analyzed using infrared spectroscopy (FTIR), thermo-gravimetric analysis (TG/DTG) and X- ray diffraction (XRD) techniques to determine the mineralogical phase transition. The results of mechanical properties are in a good agreement with those of FTIR, TG/DTG and XRD techniques and confirm that the SRR during ageing increases with MK content.