Mikhail M. Vasiliev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mikhail M. Vasiliev has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Sergey V. Starinskiy
Kutateladze Institute of Thermophysics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
6 shared publications - Alexey A. Rodionov
Kutateladze Institute of Thermophysics, Siberian Branch, Russian Academy of Sciences 1 , 1 Lavrentiev Ave., Novosibirsk 630090
4 shared publications - Maria Kandyla
Theoretical and Physical Chemistry Institute, National Hellenic Research Foundation, Athens, Greece
3 shared publications - Nikita Smirnov
Kutateladze Institute of Thermophysics, Siberian Branch, Russian Academy of Sciences 1 , 1 Lavrentiev Ave., Novosibirsk 630090
3 shared publications - Theodoros Giannakis
National Hellenic Research Foundation 48 Vasileos Constantinou Avenue
3 shared publications - Veronica S. Sulyaeva
Nikolaev Institute of Inorganic Chemistry, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
3 shared publications
Latest Publications
- Open Access
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Role of melting, evaporation, and plasma shielding in surface morphology formation during nanosecond laser texturing
This paper presents a systematic study of silicon microstructure formation under nanosecond laser irradiation in a low-pressure environment. The laser pulse fluence is shown to be the key parameter governing surface morphology. Based on scanning electron microscopy analysis, four stable types of laser-modified surfaces are identified: low-fluence modified surface, black silicon (B-Si), gray silicon (GraySi), and high-fluence modified surface. The plasma shielding efficiency is experimentally quantified over a wide fluence range. An adapted thermal numerical model incorporating plasma shielding is validated against the experimentally determined silicon modification threshold and mass removal data. The results demonstrate that B-Si formation occurs in a regime dominated by hydrodynamic processes in the molten layer with minimal evaporation, whereas GraySi emerges under conditions of enhanced evaporation and significant plasma shielding.
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessRole of melting, evaporation, and plasma shielding in surface morphology formation during nanosecond laser texturing
This paper presents a systematic study of silicon microstructure formation under nanosecond laser irradiation in a low-pressure environment. The laser pulse fluence is shown to be the key parameter governing surface morphology. Based on scanning electron microscopy analysis, four stable types of laser-modified surfaces are identified: low-fluence modified surface, black silicon (B-Si), gray silicon (GraySi), and high-fluence modified surface. The plasma shielding efficiency is experimentally quantified over a wide fluence range. An adapted thermal numerical model incorporating plasma shielding is validated against the experimentally determined silicon modification threshold and mass removal data. The results demonstrate that B-Si formation occurs in a regime dominated by hydrodynamic processes in the molten layer with minimal evaporation, whereas GraySi emerges under conditions of enhanced evaporation and significant plasma shielding.
- 30 November 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 286
Effect of micro- and nanostructure of superheated laser-textured silicon on water droplet boiling dynamics
- 30 November 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 286
Effect of micro- and nanostructure of superheated laser-textured silicon on water droplet boiling dynamics
- 6 February 2023
- Published by AIP Publishing
- Vol. 35 (2) , 025109
10.1063/5.0136468.1
An experimental study of the cavitation flow around the National Advisory Committee for Aeronautics 0012 hydrofoil with different surface morphology was carried out in this work. The surface morphology was set by modern laser ablation technology. The average values and intensity of vapor–gas cavities were determined. It has been revealed that laser texturing delays the emerging cavitation and somewhat decreases its intensity at higher cavitation numbers. A decrease in the cavitation number leads to an increase in its intensity for a smooth hydrofoil in comparison with a rough one, which is also expressed in an increase in the frequency of cavities. The paper presents a comparison of the flow regime with equal cavitation numbers, which clearly describes the features of the development of a vapor–gas cavity on the suction side of the foil with different surface morphologies. The paper provides an explanation of the reasons for the influence of surface morphology on the development of cavities.
- 6 February 2023
- Published by AIP Publishing
- Vol. 35 (2) , 025109
10.1063/5.0136468.1
An experimental study of the cavitation flow around the National Advisory Committee for Aeronautics 0012 hydrofoil with different surface morphology was carried out in this work. The surface morphology was set by modern laser ablation technology. The average values and intensity of vapor–gas cavities were determined. It has been revealed that laser texturing delays the emerging cavitation and somewhat decreases its intensity at higher cavitation numbers. A decrease in the cavitation number leads to an increase in its intensity for a smooth hydrofoil in comparison with a rough one, which is also expressed in an increase in the frequency of cavities. The paper presents a comparison of the flow regime with equal cavitation numbers, which clearly describes the features of the development of a vapor–gas cavity on the suction side of the foil with different surface morphologies. The paper provides an explanation of the reasons for the influence of surface morphology on the development of cavities.
- 1 February 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (2)
Effect of a textured surface on the occurrence and development of cavitation on the hydrofoil
An experimental study of the cavitation flow around the National Advisory Committee for Aeronautics 0012 hydrofoil with different surface morphology was carried out in this work. The surface morphology was set by modern laser ablation technology. The average values and intensity of vapor–gas cavities were determined. It has been revealed that laser texturing delays the emerging cavitation and somewhat decreases its intensity at higher cavitation numbers. A decrease in the cavitation number leads to an increase in its intensity for a smooth hydrofoil in comparison with a rough one, which is also expressed in an increase in the frequency of cavities. The paper presents a comparison of the flow regime with equal cavitation numbers, which clearly describes the features of the development of a vapor–gas cavity on the suction side of the foil with different surface morphologies. The paper provides an explanation of the reasons for the influence of surface morphology on the development of cavities.
- 1 February 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (2)
Effect of a textured surface on the occurrence and development of cavitation on the hydrofoil
An experimental study of the cavitation flow around the National Advisory Committee for Aeronautics 0012 hydrofoil with different surface morphology was carried out in this work. The surface morphology was set by modern laser ablation technology. The average values and intensity of vapor–gas cavities were determined. It has been revealed that laser texturing delays the emerging cavitation and somewhat decreases its intensity at higher cavitation numbers. A decrease in the cavitation number leads to an increase in its intensity for a smooth hydrofoil in comparison with a rough one, which is also expressed in an increase in the frequency of cavities. The paper presents a comparison of the flow regime with equal cavitation numbers, which clearly describes the features of the development of a vapor–gas cavity on the suction side of the foil with different surface morphologies. The paper provides an explanation of the reasons for the influence of surface morphology on the development of cavities.