Robert Weber
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Robert Weber has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Benjamin Fumey
Competence Centre for Thermal Energy Systems and Process Engineering Lucerne University of Applied Sciences and Arts Horw Switzerland
3 shared publications - Adam Philip Harvey
Harmsen Consultancy BV, Nieuwerkerk aan den Ijssel, Netherlands
2 shared publications - Bhavik R. Bakshi
Arizona State University
2 shared publications Billy B. Bardin
Dow, Midland, USA
2 shared publications- Carla S. M. Pereira
Hong Kong University of Science and Technology, Hong Kong
2 shared publications Carmo J. Pereira
Wichita State University -Retired, Wichita, USA
2 shared publications
Latest Publications
- Open Access
- 10 February 2025
- Published by Elsevier in Energy and Buildings
- Vol. 332
Liquid sorption storage for high solar fraction heat supply in residential buildings under different climatic conditions
- 10 February 2025
- Published by Elsevier in Energy and Buildings
- Vol. 332
Open AccessLiquid sorption storage for high solar fraction heat supply in residential buildings under different climatic conditions
- Open Access
- 19 October 2023
- Published by Wiley in Journal of Advanced Manufacturing and Processing
- Vol. 5 (4)
Issue Information
- 19 October 2023
- Published by Wiley in Journal of Advanced Manufacturing and Processing
- Vol. 5 (4)
Open AccessIssue Information
- Open Access
- 18 July 2023
- Published by Wiley in Journal of Advanced Manufacturing and Processing
- Vol. 5 (3)
Issue Information
- 18 July 2023
- Published by Wiley in Journal of Advanced Manufacturing and Processing
- Vol. 5 (3)
Open AccessIssue Information
- Open Access
- 7 February 2023
- Published by Elsevier in Applied Energy
- Vol. 335
Heat transfer constraints and performance mapping of a closed liquid sorption heat storage process
- 7 February 2023
- Published by Elsevier in Applied Energy
- Vol. 335
Open AccessHeat transfer constraints and performance mapping of a closed liquid sorption heat storage process
- Open Access
- 9 July 2021
- Published by Springer Nature in GPS Solutions
- Vol. 25 (4) , 1
Correction to: PPP with integer ambiguity resolution for GPS and Galileo using satellite products from different analysis centers
- 9 July 2021
- Published by Springer Nature in GPS Solutions
- Vol. 25 (4) , 1
Open AccessCorrection to: PPP with integer ambiguity resolution for GPS and Galileo using satellite products from different analysis centers
- Open Access
- 23 March 2020
- Published by Copernicus GmbH
GNSS/IMU/Odometer based Train Positioning
Usually train positioning is realized via counting wheel rotations (Odometer), and correcting at fixed locations known as balises. A balise is an electronic beacon or transponder placed between the rails of a railway as part of an automatic train protection (ATP) system. Balises constitute an integral part of the European Train Control System, where they serve as “beacons” giving the exact location of a train. Unfortunately, balises are expensive sensors which need to be placed over about 250 000 km of train tracks in Europe.Therefore, recently tremendous efforts aim on the development of satellite-based techniques in combination with further sensors to ensure precise train positioning. A fusion of GNSS receiver and Inertial Navigation Unit (IMU) observations processed within a Kalman Filter proved to be one of potential optimal solutions for train traction vehicles positioning.Today several hundreds of trains in Austria are equipped with a single-frequency GPS/GLONASS unit. However, when the GNSS signal fails (e.g. tunnels and urban areas), we expect an outage or at least a limited positioning quality. To yet ensure availability of a reliable trajectory in these areas, the GNSS sensor is complemented by a strapdown IMU platform and a wheel speed sensor (odometer).In this study a filtering algorithm based on the fusion of three sensors GPS, IMU and odometer is presented, which enables a reliable train positioning performance in post-processing. Odometer data are counts of impulses, which relate the wheel’s circumference to the velocity and the distance traveled by the train. This odometer data provides non-holonomic constraints as one-dimensional velocity updates and complements the basic IMU/GPS navigation system. These updates improve the velocity and attitude estimates of the train at high update rates while GPS data is used to provide accurate determination in position with low rates. In case of GNSS outages, the integrated system can switch to IMU/odometer mode. Using the exponentially weighted moving average method to estimate of measurement noise for odometer velocity helps to construct measurement covariance matrices. In the presented examples an IMU device, a GPS receiver and an Odometer provide the data input for the loosely coupled Kalman Filter integration algorithm. The quality of our solution was tested against trajectories obtained with the software iXCOM-CMD (iMAR) as reference.
- 23 March 2020
- Published by Copernicus GmbH
Open AccessGNSS/IMU/Odometer based Train Positioning
Usually train positioning is realized via counting wheel rotations (Odometer), and correcting at fixed locations known as balises. A balise is an electronic beacon or transponder placed between the rails of a railway as part of an automatic train protection (ATP) system. Balises constitute an integral part of the European Train Control System, where they serve as “beacons” giving the exact location of a train. Unfortunately, balises are expensive sensors which need to be placed over about 250 000 km of train tracks in Europe.Therefore, recently tremendous efforts aim on the development of satellite-based techniques in combination with further sensors to ensure precise train positioning. A fusion of GNSS receiver and Inertial Navigation Unit (IMU) observations processed within a Kalman Filter proved to be one of potential optimal solutions for train traction vehicles positioning.Today several hundreds of trains in Austria are equipped with a single-frequency GPS/GLONASS unit. However, when the GNSS signal fails (e.g. tunnels and urban areas), we expect an outage or at least a limited positioning quality. To yet ensure availability of a reliable trajectory in these areas, the GNSS sensor is complemented by a strapdown IMU platform and a wheel speed sensor (odometer).In this study a filtering algorithm based on the fusion of three sensors GPS, IMU and odometer is presented, which enables a reliable train positioning performance in post-processing. Odometer data are counts of impulses, which relate the wheel’s circumference to the velocity and the distance traveled by the train. This odometer data provides non-holonomic constraints as one-dimensional velocity updates and complements the basic IMU/GPS navigation system. These updates improve the velocity and attitude estimates of the train at high update rates while GPS data is used to provide accurate determination in position with low rates. In case of GNSS outages, the integrated system can switch to IMU/odometer mode. Using the exponentially weighted moving average method to estimate of measurement noise for odometer velocity helps to construct measurement covariance matrices. In the presented examples an IMU device, a GPS receiver and an Odometer provide the data input for the loosely coupled Kalman Filter integration algorithm. The quality of our solution was tested against trajectories obtained with the software iXCOM-CMD (iMAR) as reference.
- 1 January 2000
- Published by Springer Nature
- p. 169-172
Orbit Modelling Based on Laser and CCD-Observations
- 1 January 2000
- Published by Springer Nature
- p. 169-172
Orbit Modelling Based on Laser and CCD-Observations