Fernanda Signor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fernanda Signor has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Angélica Daiane Schneider
Postgraduate Program in Physics (PGFisica), Department of Physics, Federal University of Santa Maria, Santa Maria, Brazil
1 shared publication - Carlos Eduardo de Souza
Department of Mechanical Engineering, Federal University of Rio Grande do Sul (UFRGS), Porto Alegre, Brazil
1 shared publication - Caroline Raquel Bender
Núcleo de Química de Heterociclos (NUQUIMHE), Department of Chemistry, Federal University of Santa Maria (UFSM), 97105-900, Santa Maria, RS, Brazil
1 shared publication Caroline Schwantes Baumgratz
Universidade Federal de Santa Maria
1 shared publication- Diego Michael Cornelius dos Santos
Universidade Federal de Santa Maria, Brasil
1 shared publication Fabrício Luiz Faita
1 shared publication
Latest Publications
- 9 October 2024
- Published by SAGE Publications in International Journal of Mechanical Engineering Education
- Vol. 54 (1) , 173-191
Aerodynamics learning based on the development of an simplified conceptual glider design and flight testing
This study explores numerically and experimentally the conceptual design of a glider aircraft, focusing on achieving stable and efficient flight. The purpose of the work was the applied learning of aerodynamics for an undergraduate course in aerospace engineering. After research, simulations, and theoretical analyses, the project progressed to the practical stage, involving the construction and flight testing of the aircraft. This research included the identification of possible airfoils, consideration of Reynolds number limits and detailed analyses in XFLR5. Methods such as the Lifting Line Theorem and the Vortex Lattice Method were studied and applied in the project development.This approach underlines the study’s education aim - to demonstrate the practical application of theoretical knowledge. In summary, the design process, emphasizing the key milestones and challenges encountered during the manufacturing phase and the outcomes of the flight tests are discussed in detail. The project enabled the simulation and validation of aerodynamic concepts through construction, yielding flight results that were consistent with previous numerical predictions. This demonstrates that the proposed educational approach significantly enhances the practical application of theoretical knowledge in aerodynamics.
- 9 October 2024
- Published by SAGE Publications in International Journal of Mechanical Engineering Education
- Vol. 54 (1) , 173-191
Aerodynamics learning based on the development of an simplified conceptual glider design and flight testing
This study explores numerically and experimentally the conceptual design of a glider aircraft, focusing on achieving stable and efficient flight. The purpose of the work was the applied learning of aerodynamics for an undergraduate course in aerospace engineering. After research, simulations, and theoretical analyses, the project progressed to the practical stage, involving the construction and flight testing of the aircraft. This research included the identification of possible airfoils, consideration of Reynolds number limits and detailed analyses in XFLR5. Methods such as the Lifting Line Theorem and the Vortex Lattice Method were studied and applied in the project development.This approach underlines the study’s education aim - to demonstrate the practical application of theoretical knowledge. In summary, the design process, emphasizing the key milestones and challenges encountered during the manufacturing phase and the outcomes of the flight tests are discussed in detail. The project enabled the simulation and validation of aerodynamic concepts through construction, yielding flight results that were consistent with previous numerical predictions. This demonstrates that the proposed educational approach significantly enhances the practical application of theoretical knowledge in aerodynamics.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 27, e20230478
Powder Metallurgical Manufacturing of Ti-Nb alloys Using Coarse Nb Powders
Powder metallurgy is an attractive method for cost effective production of near net shape Ti-Nb alloys, and, when elemental powders and coarse HDH powders are used, a higher flexibility in alloy composition and low processing costs can be achieved. In this study, manufacturing of (α+β) Ti-Nb alloys by powder metallurgical techniques using coarse HDH Nb (D50= 110 μm and D50= 255 μm) and HDH Ti (D50= 22.6 μm) powders as starting materials was described. Tape casting was applied for the production of porous sheets while warm compaction of Metal Injection Molding (MIM) feedstock was applied for the production of dense parts. Microstructural and mechanical tests were employed to investigated the effect of coarse Nb powders on the sintering behavior and mechanical properties. Tape casting enabled to produce porous sheets of Ti16Nb alloy with an interconnected porosity varying from 14 - 31 vol.%. Warm compaction enabled to produce Ti-Nb parts with less than 2% porosity and Yield strength in compression of 975-1100 MPa, which is similar to the values reported for Ti-Nb based alloys produced by powder metallurgy of finer powders. A dynamic Young’s Modulus of 37-52 GPa, significantly lower than that of cp-Ti was achieved. These results might provide guidelines for the use of coarse Nb powders as starting materials for the powder metallurgical development of low-cost Ti-Nb based alloys.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 27, e20230478
Open AccessPowder Metallurgical Manufacturing of Ti-Nb alloys Using Coarse Nb Powders
Powder metallurgy is an attractive method for cost effective production of near net shape Ti-Nb alloys, and, when elemental powders and coarse HDH powders are used, a higher flexibility in alloy composition and low processing costs can be achieved. In this study, manufacturing of (α+β) Ti-Nb alloys by powder metallurgical techniques using coarse HDH Nb (D50= 110 μm and D50= 255 μm) and HDH Ti (D50= 22.6 μm) powders as starting materials was described. Tape casting was applied for the production of porous sheets while warm compaction of Metal Injection Molding (MIM) feedstock was applied for the production of dense parts. Microstructural and mechanical tests were employed to investigated the effect of coarse Nb powders on the sintering behavior and mechanical properties. Tape casting enabled to produce porous sheets of Ti16Nb alloy with an interconnected porosity varying from 14 - 31 vol.%. Warm compaction enabled to produce Ti-Nb parts with less than 2% porosity and Yield strength in compression of 975-1100 MPa, which is similar to the values reported for Ti-Nb based alloys produced by powder metallurgy of finer powders. A dynamic Young’s Modulus of 37-52 GPa, significantly lower than that of cp-Ti was achieved. These results might provide guidelines for the use of coarse Nb powders as starting materials for the powder metallurgical development of low-cost Ti-Nb based alloys.
- 11 February 2023
- Published by Elsevier in Materials Letters
- Vol. 338
Solution heat treatment of Ti-Nb alloys using a molten salt shield
- 11 February 2023
- Published by Elsevier in Materials Letters
- Vol. 338
Solution heat treatment of Ti-Nb alloys using a molten salt shield