Robert Shandro
Robert Shandro has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Aishwarya
Cetim-Matcor Technology & Services Pte. Ltd., 3 Seletar Aerospace Link, Singapore 797550, Singapore
1 shared publication - Aprilia Aprilia
Rolls-Royce@NTU Corporate Laboratory, Nanyang Technological University, 65 Nanyang Drive, Singapore 637460, Singapore
1 shared publication - Fabien Lefebvre
CETIM
1 shared publication - Ivanna Pivdiablyk
Cetim-Matcor Technology and Services, 3 Seletar Aerospace Link, Singapore 797550, Singapore
1 shared publication - Liam Kok Chye
Cetim-Matcor Technology and Services, 3 Seletar Aerospace Link, Singapore 797550, Singapore
1 shared publication - Wei Zhou
Singapore Centre for 3D Printing, School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore
1 shared publication
Latest Publications
- Open Access
Decarburization of Wire-Arc Additively Manufactured ER70S-6 Steel
Decarburization is an unwanted carbon-loss phenomenon on the surfaces of a material when they are exposed to oxidizing environments at elevated temperatures. Decarburization of steels after heat treatment has been widely studied and reported. However, up to now, there has not been any systematic study on the decarburization of additively manufactured parts. Wire-arc additive manufacturing (WAAM) is an efficient additive manufacturing process for producing large engineering parts. As the parts produced by WAAM are usually large in size, the use of a vacuum environment to prevent decarburization is not always feasible. Therefore, there is a need to study the decarburization of WAAM-produced parts, especially after the heat treatment processes. This study investigated the decarburization of a WAAM-produced ER70S-6 steel using both the as-printed material and samples heat-treated at different temperatures (800 °C, 850 °C, 900 °C, and 950 °C) for different durations (30 min, 60 min, and 90 min). Furthermore, numerical simulation was carried out using Thermo-Calc computational software to predict the carbon concentration profiles of the steel during the heat treatment processes. Decarburization was found to occur not only in the heat-treated samples but also on the surfaces of the as-printed parts (despite the use of Ar for shielding). The decarburization depth was found to increase with an increase in heat treatment temperature or duration. The part heat-treated at the lowest temperature of 800 °C for merely 30 min was observed to have a large decarburization depth of about 200 μm. For the same heating duration of 30 min, an increase in temperature of 150 °C to 950 °C increased the decarburization depth drastically by 150% to 500 μm. This study serves well to demonstrate the need for further study to control or minimize decarburization for the purpose of ensuring the quality and reliability of additively manufactured engineering components.
Open AccessDecarburization of Wire-Arc Additively Manufactured ER70S-6 Steel
Decarburization is an unwanted carbon-loss phenomenon on the surfaces of a material when they are exposed to oxidizing environments at elevated temperatures. Decarburization of steels after heat treatment has been widely studied and reported. However, up to now, there has not been any systematic study on the decarburization of additively manufactured parts. Wire-arc additive manufacturing (WAAM) is an efficient additive manufacturing process for producing large engineering parts. As the parts produced by WAAM are usually large in size, the use of a vacuum environment to prevent decarburization is not always feasible. Therefore, there is a need to study the decarburization of WAAM-produced parts, especially after the heat treatment processes. This study investigated the decarburization of a WAAM-produced ER70S-6 steel using both the as-printed material and samples heat-treated at different temperatures (800 °C, 850 °C, 900 °C, and 950 °C) for different durations (30 min, 60 min, and 90 min). Furthermore, numerical simulation was carried out using Thermo-Calc computational software to predict the carbon concentration profiles of the steel during the heat treatment processes. Decarburization was found to occur not only in the heat-treated samples but also on the surfaces of the as-printed parts (despite the use of Ar for shielding). The decarburization depth was found to increase with an increase in heat treatment temperature or duration. The part heat-treated at the lowest temperature of 800 °C for merely 30 min was observed to have a large decarburization depth of about 200 μm. For the same heating duration of 30 min, an increase in temperature of 150 °C to 950 °C increased the decarburization depth drastically by 150% to 500 μm. This study serves well to demonstrate the need for further study to control or minimize decarburization for the purpose of ensuring the quality and reliability of additively manufactured engineering components.
- Open Access
Residual Creep Life Assessment of High-Temperature Components in Power Industry
A large percentage of power, petroleum, and chemical plants over the world were in operation for a long duration with the corresponding critical components being used beyond the design life of 30 to 40 years. It is generally more cost-effective to refurbish or modernize the degraded equipment or components, rather than to construct a new plant. Therefore, a reliable plant life extension assessment that can evaluate the critical components is needed. The key element in plant life extension is the residual life assessment technology. However, at present, there is still no general consensus among the industry players on the approach to adopt when performing residual life assessment for such a critical damage mechanism as creep. In this article, a three-level residual life assessment methodology is proposed as a general approach for high-temperature components prone to creep. A detailed validation of the selected guidelines and calculation models is also described. Eventually, an application of the three-level methodology to a real industrial case study is presented.
Open AccessResidual Creep Life Assessment of High-Temperature Components in Power Industry
A large percentage of power, petroleum, and chemical plants over the world were in operation for a long duration with the corresponding critical components being used beyond the design life of 30 to 40 years. It is generally more cost-effective to refurbish or modernize the degraded equipment or components, rather than to construct a new plant. Therefore, a reliable plant life extension assessment that can evaluate the critical components is needed. The key element in plant life extension is the residual life assessment technology. However, at present, there is still no general consensus among the industry players on the approach to adopt when performing residual life assessment for such a critical damage mechanism as creep. In this article, a three-level residual life assessment methodology is proposed as a general approach for high-temperature components prone to creep. A detailed validation of the selected guidelines and calculation models is also described. Eventually, an application of the three-level methodology to a real industrial case study is presented.