Yury I. Shtern
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yury I. Shtern has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Maxim S. Rogachev
National Research University of Electronic Technology, Moscow, Russia
5 shared publications - Maxim Yu. Shtern
National Research University of Electronic Technology (MIET), Moscow, Russia
5 shared publications - Alexey A. Sherchenkov
National Research University of Electronic Technology, Moscow, Russia
2 shared publications - E. P. Korchagin
Национальный исследовательский университет «Московский институт электронной техники
2 shared publications A. A. Sherchenkov
National Research University of Electronic Technology (MIET), Moscow, Russia
1 shared publication- Alexander Yurevich Gerasimenko
Institute of Biomedical Systems, National Research University of Electronic Technology, 124498 Zelenograd, Russia
1 shared publication
Latest Publications
- Open Access
- 30 September 2026
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 12 (3) , 113-130
Challenges and strategy for developing efficient thermoelectric materials based on zinc and magnesium antimonides
Zn and Mg antimonides are positioned as effective thermoelectric materials for thermoelements with operating temperatures from 300 to 800 K. Optimal compositions, doping, and methods for producing thermoelectric materials have been established. The p -type β-Zn 4 Sb 3 has the maximum dimensionless thermoelectric figure of merit ZT of 1.40–1.57 and average ZT up to 1.10 in the range of 300–720 K. Maximum ZT of thermoelectric materials on the basis of n -type Mg 3 Sb 2 is 1.65–2.00, with average ZT of 1.20–1.36 in the range of 300–800 K. Maximum ZT of p -type MgAgSb is 1.50, with average ZT of 1.31 in the range of 300–573 K. Practical application of thermoelectric materials is limited by the difficulty of obtaining a single-phase material. Another significant problem is their thermal instability.
- 30 September 2026
- Published by Pensoft Publishers in Modern Electronic Materials
- Vol. 12 (3) , 113-130
Open AccessChallenges and strategy for developing efficient thermoelectric materials based on zinc and magnesium antimonides
Zn and Mg antimonides are positioned as effective thermoelectric materials for thermoelements with operating temperatures from 300 to 800 K. Optimal compositions, doping, and methods for producing thermoelectric materials have been established. The p -type β-Zn 4 Sb 3 has the maximum dimensionless thermoelectric figure of merit ZT of 1.40–1.57 and average ZT up to 1.10 in the range of 300–720 K. Maximum ZT of thermoelectric materials on the basis of n -type Mg 3 Sb 2 is 1.65–2.00, with average ZT of 1.20–1.36 in the range of 300–800 K. Maximum ZT of p -type MgAgSb is 1.50, with average ZT of 1.31 in the range of 300–573 K. Practical application of thermoelectric materials is limited by the difficulty of obtaining a single-phase material. Another significant problem is their thermal instability.
- 18 September 2026
- Published by Technosphera JSC in Nanoindustry Russia
- Vol. 19 (6)
ИССЛЕДОВАНИЕ ЗАЩИТНЫХ ПОКРЫТИЙ ДЛЯ ВЫСОКОТЕМПЕРАТУРНЫХ ТЕРМОЭЛЕМЕНТОВ
Для термоэлементов с рабочими температурами до 700°C, изготовленными из термоэлектрических материалов на основе BiSbTe, PbTe, GeTe и SiGe, разработаны защитные покрытия на основе полиимидного лака АД-9103, кремнийорганической эмали ElconSi, а также SiO2 и Si3N4. Проведены исследования термической стабильности в интервале рабочих температур термоэлементов, а также адгезионной прочности защитных покрытий. Покрытия АД-9103 и ElconSi толщиной 25 и 15 мкм, соответственно, обеспечивают стабильность свойств термоэлементов при температурах до 300°C, а покрытия SiO2 и Si3N4 толщиной 1 мкм до 700°C. Адгезионная прочность, определенная методом прямого отрыва, составила для органических покрытий 900–1000 г/мм2, а для покрытий SiO2 и Si3N4 1080–1250 г/мм2. Разработанные покрытия предназначены для изготовления высокотемпературных термоэлементов, используемых в ТЭГ.
- 18 September 2026
- Published by Technosphera JSC in Nanoindustry Russia
- Vol. 19 (6)
ИССЛЕДОВАНИЕ ЗАЩИТНЫХ ПОКРЫТИЙ ДЛЯ ВЫСОКОТЕМПЕРАТУРНЫХ ТЕРМОЭЛЕМЕНТОВ
Для термоэлементов с рабочими температурами до 700°C, изготовленными из термоэлектрических материалов на основе BiSbTe, PbTe, GeTe и SiGe, разработаны защитные покрытия на основе полиимидного лака АД-9103, кремнийорганической эмали ElconSi, а также SiO2 и Si3N4. Проведены исследования термической стабильности в интервале рабочих температур термоэлементов, а также адгезионной прочности защитных покрытий. Покрытия АД-9103 и ElconSi толщиной 25 и 15 мкм, соответственно, обеспечивают стабильность свойств термоэлементов при температурах до 300°C, а покрытия SiO2 и Si3N4 толщиной 1 мкм до 700°C. Адгезионная прочность, определенная методом прямого отрыва, составила для органических покрытий 900–1000 г/мм2, а для покрытий SiO2 и Si3N4 1080–1250 г/мм2. Разработанные покрытия предназначены для изготовления высокотемпературных термоэлементов, используемых в ТЭГ.
- 18 July 2024
- Published by The Russian Academy of Sciences in Žurnal prikladnoj himii
- Vol. 97 (1) , 45-51
Контакты для термоэлементов с барьерными слоями на основе вольфрама
Предложен способ получения контактов на основе W–Ni и W–Co, выполняющих функции диффузионно-барьерных слоев в конструкции термоэлементов. Контакты сформированы электрохимическим осаждением пленок W–Ni и W–Co на образцах наноструктурированных термоэлектрических материалов на основе Bi2Te2.4Se0.6, Bi0.4Sb1.6Te3, GeTe и PbTe, используемых для изготовления термоэлементов. Получены пленки толщиной до 15 мкм с разбросом по толщине не более 5%. Содержание вольфрама в составе пленок W–Ni составило 33.5 мас%, в пленках W–Co — 29.7 мас%. Удельное сопротивление и удельное контактное сопротивление пленок составило 3.4∙10–7 Ом∙м и 3.8∙10–9 Ом∙м2 соответственно. Адгезионная прочность пленок составляет 10−13 МПа. Установлено, что контакты, сформированные на образцах термоэлектрических материалов электрохимическим осаждением пленок на основе W–Co, могут быть использованы в конструкции термоэлементов с рабочими температурами до 900 K.
- 18 July 2024
- Published by The Russian Academy of Sciences in Žurnal prikladnoj himii
- Vol. 97 (1) , 45-51
Контакты для термоэлементов с барьерными слоями на основе вольфрама
Предложен способ получения контактов на основе W–Ni и W–Co, выполняющих функции диффузионно-барьерных слоев в конструкции термоэлементов. Контакты сформированы электрохимическим осаждением пленок W–Ni и W–Co на образцах наноструктурированных термоэлектрических материалов на основе Bi2Te2.4Se0.6, Bi0.4Sb1.6Te3, GeTe и PbTe, используемых для изготовления термоэлементов. Получены пленки толщиной до 15 мкм с разбросом по толщине не более 5%. Содержание вольфрама в составе пленок W–Ni составило 33.5 мас%, в пленках W–Co — 29.7 мас%. Удельное сопротивление и удельное контактное сопротивление пленок составило 3.4∙10–7 Ом∙м и 3.8∙10–9 Ом∙м2 соответственно. Адгезионная прочность пленок составляет 10−13 МПа. Установлено, что контакты, сформированные на образцах термоэлектрических материалов электрохимическим осаждением пленок на основе W–Co, могут быть использованы в конструкции термоэлементов с рабочими температурами до 900 K.
- 8 December 2023
- Published by Pleiades Publishing Ltd in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
- Vol. 17 (6) , 1207-1216
Preparation of the Thermoelement Surfaces and Investigation of Ohmic Film Contacts Formed on Them by Different Methods
Methods are proposed and criteria are established for preparing the surface of nanostructured thermoelectric materials for the deposition of thin- and thick-film ohmic contacts. The parameters of the mechanical and chemical methods of thermoelectric material surface treatment before the deposition of the contact. The roughness and morphology of the surface of thermoelectric material samples and the films obtained are studied. The criteria and optimal values of the surface roughness of thermoelectric materials are established. The conditions of obtaining thin- and thick-film contacts are determined. Thin-film contacts (thickness up to 300 nm) are obtained by the magnetron sputtering of Ni. Thick-film contacts are formed by the chemical and electrochemical deposition of Ni. The obtained films contain various amounts of Ni. The electrical resistivity of the Ni films obtained by chemical deposition is significantly higher than that of Ni films obtained by electrochemical deposition. The specific contact resistance of the metal–thermoelectric material system in the case of the deposition of Ni films by magnetron sputtering is the smallest among the considered samples. In the case of forming contacts by chemical deposition, it is comparable to that for Ni films formed by electrochemical deposition. The adhesion strength of Ni films obtained by various methods has high values exceeding the industry standard for film coatings in microelectronics. All obtained ohmic contacts satisfy the requirements for the construction of efficient thermoelements in terms of electrical properties and adhesion strength.
- 8 December 2023
- Published by Pleiades Publishing Ltd in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
- Vol. 17 (6) , 1207-1216
Preparation of the Thermoelement Surfaces and Investigation of Ohmic Film Contacts Formed on Them by Different Methods
Methods are proposed and criteria are established for preparing the surface of nanostructured thermoelectric materials for the deposition of thin- and thick-film ohmic contacts. The parameters of the mechanical and chemical methods of thermoelectric material surface treatment before the deposition of the contact. The roughness and morphology of the surface of thermoelectric material samples and the films obtained are studied. The criteria and optimal values of the surface roughness of thermoelectric materials are established. The conditions of obtaining thin- and thick-film contacts are determined. Thin-film contacts (thickness up to 300 nm) are obtained by the magnetron sputtering of Ni. Thick-film contacts are formed by the chemical and electrochemical deposition of Ni. The obtained films contain various amounts of Ni. The electrical resistivity of the Ni films obtained by chemical deposition is significantly higher than that of Ni films obtained by electrochemical deposition. The specific contact resistance of the metal–thermoelectric material system in the case of the deposition of Ni films by magnetron sputtering is the smallest among the considered samples. In the case of forming contacts by chemical deposition, it is comparable to that for Ni films formed by electrochemical deposition. The adhesion strength of Ni films obtained by various methods has high values exceeding the industry standard for film coatings in microelectronics. All obtained ohmic contacts satisfy the requirements for the construction of efficient thermoelements in terms of electrical properties and adhesion strength.
- 20 February 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 946
Mechanical properties and thermal stability of nanostructured thermoelectric materials on the basis of PbTe and GeTe
- 20 February 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 946
Mechanical properties and thermal stability of nanostructured thermoelectric materials on the basis of PbTe and GeTe