Fei Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fei Li has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Chang Liu
The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan, P.R. China
1 shared publication - Chao Li
School of materials science and chemical engineering, Harbin University of Science and Technology, Harbin, China
1 shared publication - Dou Wang
Institute of Materials, China Academy of Engineering Physics, Mianyang 621908, China
1 shared publication Fenggang Liu
School of Metallurgical and Ecological Engineering University of Science and Technology Beijing (USTB) Beijing 100083 China
1 shared publication- Fengsheng Qu
Institute of Materials, China Academy of Engineering Physics, Mianyang 621908, China
1 shared publication Jing Zhang
School of Vehicle and Energy Yanshan University Qinhuangdao 066004 Hebei China
1 shared publication
Latest Publications
- Open Access
Electrochemical Dealloying Preparation and Morphology Evolution of Nanoporous Au with Enhanced SERS Activity
Nanoporous Au (NPG) prepared by dealloying is one of the most used substrates for surface-enhanced Raman scattering (SERS). The morphology tailoring of the NPG to obtain both ultrafine pores and suitable Au/Ag ratio is of great importance for the acquiring of enhanced SERS performance. Compared with the chemical dealloying, the electrochemical dealloying can tailor the NPG to be more flexible by the additional adjustment of dealloying voltage and current. Thus, further understanding on the morphology evolution of NPG during the electrochemical dealloying to obtain enhanced SERS performance is of great importance. In the presented work, the morphology and composition evolution of the NPG film during the electrochemical dealloying was investigated. NPG films with a stable pore diameter of approximately 11 nm as well as diverse compositions were obtained by electrochemical dealloying an Au-Ag alloy film. The prepared NPG film exhibits an enhanced SERS activity with an enhancement factor (EF) of 7.3 × 106 and an excellent detection limit of 10−9 M. This work provides insights into the morphology and composition evolution of the NPG during the electrochemical dealloying process to obtain enhanced SERS performance.
Open AccessElectrochemical Dealloying Preparation and Morphology Evolution of Nanoporous Au with Enhanced SERS Activity
Nanoporous Au (NPG) prepared by dealloying is one of the most used substrates for surface-enhanced Raman scattering (SERS). The morphology tailoring of the NPG to obtain both ultrafine pores and suitable Au/Ag ratio is of great importance for the acquiring of enhanced SERS performance. Compared with the chemical dealloying, the electrochemical dealloying can tailor the NPG to be more flexible by the additional adjustment of dealloying voltage and current. Thus, further understanding on the morphology evolution of NPG during the electrochemical dealloying to obtain enhanced SERS performance is of great importance. In the presented work, the morphology and composition evolution of the NPG film during the electrochemical dealloying was investigated. NPG films with a stable pore diameter of approximately 11 nm as well as diverse compositions were obtained by electrochemical dealloying an Au-Ag alloy film. The prepared NPG film exhibits an enhanced SERS activity with an enhancement factor (EF) of 7.3 × 106 and an excellent detection limit of 10−9 M. This work provides insights into the morphology and composition evolution of the NPG during the electrochemical dealloying process to obtain enhanced SERS performance.
- 22 July 2021
- Published by Wiley in Steel Research International
- Vol. 92 (10) , 2000608
Water Modeling on Circulating Flow and Mixing Time in a Ruhrstahl–Heraeus Vacuum Degasser
A physical water model based on the similarity principle is established to investigate the fluid flow and mixing phenomena during the Ruhrstahl–Heraeus (RH) steel refining process. The velocity distribution and the turbulent features on the center section are obtained using particle image velocimetry (PIV) measurement. Two vortexes between the down‐leg snorkel and the ladle sidewall are observed. The effects of the number of gas‐injection nozzles and the liquid levels in the vacuum chamber on the fluid phenomena are performed. More injected nozzles and a higher liquid level in the vacuum chamber generate larger velocity in the ladle. Twenty monitors in the ladle are used to monitor the variation of the conductivity to obtain the mixing time, indicating that the mixing time varies much with locations. The distribution of the mixing time on the vertical center section of the ladle is obtained. Moreover, the relationship between the circulation rate and the mixing time is obtained, indicating that the mixing time decreases with increasing circulation rate, and the slope of their relationship is −0.35.
- 22 July 2021
- Published by Wiley in Steel Research International
- Vol. 92 (10) , 2000608
Water Modeling on Circulating Flow and Mixing Time in a Ruhrstahl–Heraeus Vacuum Degasser
A physical water model based on the similarity principle is established to investigate the fluid flow and mixing phenomena during the Ruhrstahl–Heraeus (RH) steel refining process. The velocity distribution and the turbulent features on the center section are obtained using particle image velocimetry (PIV) measurement. Two vortexes between the down‐leg snorkel and the ladle sidewall are observed. The effects of the number of gas‐injection nozzles and the liquid levels in the vacuum chamber on the fluid phenomena are performed. More injected nozzles and a higher liquid level in the vacuum chamber generate larger velocity in the ladle. Twenty monitors in the ladle are used to monitor the variation of the conductivity to obtain the mixing time, indicating that the mixing time varies much with locations. The distribution of the mixing time on the vertical center section of the ladle is obtained. Moreover, the relationship between the circulation rate and the mixing time is obtained, indicating that the mixing time decreases with increasing circulation rate, and the slope of their relationship is −0.35.