Tieqiang Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tieqiang Li has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Fengchun Cai
State Key Laboratory of Precision and Intelligent Chemistry, University of Science and Technology of China, Hefei, China
4 shared publications - Hongguang Meng
Key Laboratory of Precision and Intelligent Chemistry, CAS Key Laboratory of Materials for Energy Conversion, Department of Materials Science and Engineering University of Science and Technology of China Hefei 230026 China
4 shared publications - Jixian Xu
State Key Laboratory of Precision and Intelligent Chemistry, University of Science and Technology of China, Hefei, China
4 shared publications - Xingyu Feng
Key Laboratory of Precision and Intelligent Chemistry, CAS Key Laboratory of Materials for Energy Conversion, Department of Materials Science and Engineering University of Science and Technology of China Hefei 230026 China
4 shared publications - Kaitian Mao
Key Laboratory of Precision and Intelligent Chemistry, CAS Key Laboratory of Materials for Energy Conversion, Department of Materials Science and Engineering University of Science and Technology of China Hefei 230026 China
3 shared publications - Shaojie Yuan
Key Laboratory of Precision and Intelligent Chemistry, CAS Key Laboratory of Materials for Energy Conversion, Department of Materials Science and Engineering University of Science and Technology of China Hefei 230026 China
3 shared publications
Latest Publications
- 30 July 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (42)
Low‐Temperature Atomic Layer Deposition of Hole Transport Layers for Enhanced Performance and Scalability in Textured Perovskite/Silicon Tandem Solar Cells
Perovskite tandem solar cells on textured silicon hold potential for surpassing single‐junction limits and industrial compatibility. However, integrating hole‐transporting layers (HTLs) onto textured silicon poses challenges in conformal coating, low‐temperature fabrication, and perovskite solution process compatibility. Here, an atomic layer deposition (ALD) copper‐doping process is introduced to fabricate low‐temperature NiOx HTLs (ALD Cu:NiOx), tailored for textured tandems. Copper‐doping reduces hydroxyl group content and Ni3+ defects, addressing the challenge of enhancing hole conductivity while mitigating recombination loss. This advancement enables to lower the post‐annealing temperature from >300 to 200 °C, achieving compatibility with silicon heterojunction (SHJ) cells and boosting the power‐conversion efficiency (PCE) of 1.65‐eV p–i–n perovskite solar cells to 22.47%. Integrating ALD Cu:NiOx beneath conventional self‐assembled monolayer HTL on textured SHJ leads to notable PCE enhancements, from 28.6% to 30.5% for 1‐cm2 tandems (certified stabilized PCE of 30.04%) and from 23.9% to 26.4% for 8.89‐cm2 tandems. Following 1000 h of maximum‐power‐point (MPP) tracking, tandems maintain 95% of initial efficiency. Notably, losses in open‐circuit voltage and PCE due to area upscaling reduced by over 20%, attributed to ALD Cu:NiOx’s ability to enhance perovskite film wettability and minimize shunting on silicon pyramid texture, underscoring its impacts for textured tandem upscaling.
- 30 July 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (42)
Low‐Temperature Atomic Layer Deposition of Hole Transport Layers for Enhanced Performance and Scalability in Textured Perovskite/Silicon Tandem Solar Cells
Perovskite tandem solar cells on textured silicon hold potential for surpassing single‐junction limits and industrial compatibility. However, integrating hole‐transporting layers (HTLs) onto textured silicon poses challenges in conformal coating, low‐temperature fabrication, and perovskite solution process compatibility. Here, an atomic layer deposition (ALD) copper‐doping process is introduced to fabricate low‐temperature NiOx HTLs (ALD Cu:NiOx), tailored for textured tandems. Copper‐doping reduces hydroxyl group content and Ni3+ defects, addressing the challenge of enhancing hole conductivity while mitigating recombination loss. This advancement enables to lower the post‐annealing temperature from >300 to 200 °C, achieving compatibility with silicon heterojunction (SHJ) cells and boosting the power‐conversion efficiency (PCE) of 1.65‐eV p–i–n perovskite solar cells to 22.47%. Integrating ALD Cu:NiOx beneath conventional self‐assembled monolayer HTL on textured SHJ leads to notable PCE enhancements, from 28.6% to 30.5% for 1‐cm2 tandems (certified stabilized PCE of 30.04%) and from 23.9% to 26.4% for 8.89‐cm2 tandems. Following 1000 h of maximum‐power‐point (MPP) tracking, tandems maintain 95% of initial efficiency. Notably, losses in open‐circuit voltage and PCE due to area upscaling reduced by over 20%, attributed to ALD Cu:NiOx’s ability to enhance perovskite film wettability and minimize shunting on silicon pyramid texture, underscoring its impacts for textured tandem upscaling.
- Top Cited Papers
- 26 February 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (5) , 536-547
Inhibition of halide oxidation and deprotonation of organic cations with dimethylammonium formate for air-processed p–i–n perovskite solar cells
- 26 February 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (5) , 536-547
Top Cited PapersInhibition of halide oxidation and deprotonation of organic cations with dimethylammonium formate for air-processed p–i–n perovskite solar cells
- 30 May 2023
- Published by Wiley in Advanced Materials
- Vol. 35 (28) , e2211959
Understanding the Interfacial Reactions and Band Alignment for Efficient and Stable Perovskite Solar Cells Built on Metal Substrates with Reduced Upscaling Losses
Conventional perovskite solar cells (PSC) built on transparent conductive oxide (TCO) glass face a fundamental challenge to retain fill factor (FF) for large‐area upscaling due to series resistance loss. Building a perovskite solar cell on metal has the potential to reduce this FF loss and is promising for flexible applications. However, their efficiency and stability lag far behind their TCO counterparts. Herein, findings on the complex chemical reactions and degradation‐promoting processes at different perovskite/metal (Cu, Au, Ag, and Mo) interfaces, which are closely linked with the inherent stability; and the interlayer engineering for perovskite/metal interface's band alignment, which plays an essential role in achieving high efficiency, are reported. Leveraging these findings, 21% power conversion efficiency (PCE) is achieved for 1 cm2 perovskite solar cells using a p–i–n top‐illumination structure on a molybdenum substrate, the highest reported for a PSC built on metal. Notably, the FF and PCE losses due to area upscaling are remarkably reduced by one order of magnitude relative to the counterparts on conventional TCO glass, highlighting an alternative pathway for PSC upscaling and module design.
- 30 May 2023
- Published by Wiley in Advanced Materials
- Vol. 35 (28) , e2211959
Understanding the Interfacial Reactions and Band Alignment for Efficient and Stable Perovskite Solar Cells Built on Metal Substrates with Reduced Upscaling Losses
Conventional perovskite solar cells (PSC) built on transparent conductive oxide (TCO) glass face a fundamental challenge to retain fill factor (FF) for large‐area upscaling due to series resistance loss. Building a perovskite solar cell on metal has the potential to reduce this FF loss and is promising for flexible applications. However, their efficiency and stability lag far behind their TCO counterparts. Herein, findings on the complex chemical reactions and degradation‐promoting processes at different perovskite/metal (Cu, Au, Ag, and Mo) interfaces, which are closely linked with the inherent stability; and the interlayer engineering for perovskite/metal interface's band alignment, which plays an essential role in achieving high efficiency, are reported. Leveraging these findings, 21% power conversion efficiency (PCE) is achieved for 1 cm2 perovskite solar cells using a p–i–n top‐illumination structure on a molybdenum substrate, the highest reported for a PSC built on metal. Notably, the FF and PCE losses due to area upscaling are remarkably reduced by one order of magnitude relative to the counterparts on conventional TCO glass, highlighting an alternative pathway for PSC upscaling and module design.
- Top Cited Papers
- 17 February 2023
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 379 (6633) , 683-690
Reducing nonradiative recombination in perovskite solar cells with a porous insulator contact
Inserting an ultrathin low-conductivity interlayer between the absorber and transport layer has emerged as an important strategy for reducing surface recombination in the best perovskite solar cells. However, a challenge with this approach is a trade-off between the open-circuit voltage ( V oc ) and the fill factor (FF). Here, we overcame this challenge by introducing a thick (about 100 nanometers) insulator layer with random nanoscale openings. We performed drift-diffusion simulations for cells with this porous insulator contact (PIC) and realized it using a solution process by controlling the growth mode of alumina nanoplates. Leveraging a PIC with an approximately 25% reduced contact area, we achieved an efficiency of up to 25.5% (certified steady-state efficiency 24.7%) in p-i-n devices. The product of V oc × FF was 87.9% of the Shockley-Queisser limit. The surface recombination velocity at the p-type contact was reduced from 64.2 to 9.2 centimeters per second. The bulk recombination lifetime was increased from 1.2 to 6.0 microseconds because of improvements in the perovskite crystallinity. The improved wettability of the perovskite precursor solution allowed us to demonstrate a 23.3% efficient 1-square-centimeter p-i-n cell. We demonstrate here its broad applicability for different p-type contacts and perovskite compositions.
- 17 February 2023
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 379 (6633) , 683-690
Top Cited PapersReducing nonradiative recombination in perovskite solar cells with a porous insulator contact
Inserting an ultrathin low-conductivity interlayer between the absorber and transport layer has emerged as an important strategy for reducing surface recombination in the best perovskite solar cells. However, a challenge with this approach is a trade-off between the open-circuit voltage ( V oc ) and the fill factor (FF). Here, we overcame this challenge by introducing a thick (about 100 nanometers) insulator layer with random nanoscale openings. We performed drift-diffusion simulations for cells with this porous insulator contact (PIC) and realized it using a solution process by controlling the growth mode of alumina nanoplates. Leveraging a PIC with an approximately 25% reduced contact area, we achieved an efficiency of up to 25.5% (certified steady-state efficiency 24.7%) in p-i-n devices. The product of V oc × FF was 87.9% of the Shockley-Queisser limit. The surface recombination velocity at the p-type contact was reduced from 64.2 to 9.2 centimeters per second. The bulk recombination lifetime was increased from 1.2 to 6.0 microseconds because of improvements in the perovskite crystallinity. The improved wettability of the perovskite precursor solution allowed us to demonstrate a 23.3% efficient 1-square-centimeter p-i-n cell. We demonstrate here its broad applicability for different p-type contacts and perovskite compositions.