Arezoo Rahimi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arezoo Rahimi has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Gaofei Wang
College of Civil Engineering Nanjing Forestry University Nanjing China
1 shared publication- Guoliang Dai
School of Civil Engineering, Southeast University, Nanjing 211189, China
1 shared publication - Harianto Rahardjo
School of Civil and Environmental Engineering, Nanyang Technological University, Singapore, Singapore
1 shared publication Heping Qiu
1 shared publicationJason Ingham
1 shared publication- Jason Maxwell Ingham
Department of Civil and Environmental Engineering University of Auckland Auckland New Zealand
1 shared publication
Latest Publications
- 27 October 2026
- Published by Wiley in Structural Concrete
Experimental and numerical investigation of novel reinforced bamboo aggregate beams
To reduce the carbon emissions of concrete materials and alleviate the shortage of natural aggregate resources, this study developed bamboo coarse aggregate (BCA) concrete (BAC) and investigated the flexural performance of reinforced BAC beams using a combined experimental and numerical simulation approach, thereby filling a research gap in the application of BAC in structural members. Three‐point bending tests were conducted on six unreinforced beams and 12 stirrup‐reinforced beams, systematically investigating the effects of the longitudinal reinforcement ratio ( ρ = 0%, 1.47%, 2.34%) and the BCA replacement ratio ( r = 0%, 25%, 45%). Test results showed that as ρ increased, the failure mode of BAC reinforced beams shifted from flexural failure to shear failure. An increase in ρ enhanced the initial stiffness and ultimate deflection of the concrete beams; as r increased, the mechanical performance of the concrete beams decreased, but the peak load ( P u ) still retained more than 95% of that of the normal aggregate concrete (NAC) beams when r reached 25%. The incorporation of BCAs significantly improved the crack propagation behavior and ductility of the beams, with the ductility index increasing by up to approximately 24.6%, and BAC beams exhibited larger strains than NAC beams at the same load level. Finite element simulations successfully reproduced the failure modes and load‐deflection curves of the reinforced BAC beams observed in the tests. Finally, various standards and existing models were referenced to evaluate the ultimate moment, deflection, and shear bearing capacity of reinforced BAC beams.
- 27 October 2026
- Published by Wiley in Structural Concrete
Experimental and numerical investigation of novel reinforced bamboo aggregate beams
To reduce the carbon emissions of concrete materials and alleviate the shortage of natural aggregate resources, this study developed bamboo coarse aggregate (BCA) concrete (BAC) and investigated the flexural performance of reinforced BAC beams using a combined experimental and numerical simulation approach, thereby filling a research gap in the application of BAC in structural members. Three‐point bending tests were conducted on six unreinforced beams and 12 stirrup‐reinforced beams, systematically investigating the effects of the longitudinal reinforcement ratio ( ρ = 0%, 1.47%, 2.34%) and the BCA replacement ratio ( r = 0%, 25%, 45%). Test results showed that as ρ increased, the failure mode of BAC reinforced beams shifted from flexural failure to shear failure. An increase in ρ enhanced the initial stiffness and ultimate deflection of the concrete beams; as r increased, the mechanical performance of the concrete beams decreased, but the peak load ( P u ) still retained more than 95% of that of the normal aggregate concrete (NAC) beams when r reached 25%. The incorporation of BCAs significantly improved the crack propagation behavior and ductility of the beams, with the ductility index increasing by up to approximately 24.6%, and BAC beams exhibited larger strains than NAC beams at the same load level. Finite element simulations successfully reproduced the failure modes and load‐deflection curves of the reinforced BAC beams observed in the tests. Finally, various standards and existing models were referenced to evaluate the ultimate moment, deflection, and shear bearing capacity of reinforced BAC beams.
- Open Access
- 12 March 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 806-822
Assess the interaction of water reducers and accelerators on the rheological and early hydration properties of cement-based materials
- 12 March 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 806-822
Open AccessAssess the interaction of water reducers and accelerators on the rheological and early hydration properties of cement-based materials
- Open Access
- 24 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (5) , 4148
Effect of Base Grouting on the Bearing Capacity of Bored Piles
Post-grouting is a widely used technology for ground improvement and the strengthening of bored pile foundations. In situ experiments have shown that post-grouting is effective in improving the bearing capacity of bored piles. However, due to the cost and complexity of the in situ tests, the total number of test piles is limited. Therefore, it is not surprising that uncertainty is always associated with the collected data. This may significantly affect the conclusion of analyses, and most current studies have neglected this effect. In this paper, statistical analyses were carried out in order to investigate the effect of uncertainties in the data and the impact of post-grouting on the bearing behaviors of bored piles. The results show that post-grouting can significantly improve the bearing behavior of piles. This study is expected to provide technical guidance for post-grouting in foundation engineering.
- 24 February 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (5) , 4148
Open AccessEffect of Base Grouting on the Bearing Capacity of Bored Piles
Post-grouting is a widely used technology for ground improvement and the strengthening of bored pile foundations. In situ experiments have shown that post-grouting is effective in improving the bearing capacity of bored piles. However, due to the cost and complexity of the in situ tests, the total number of test piles is limited. Therefore, it is not surprising that uncertainty is always associated with the collected data. This may significantly affect the conclusion of analyses, and most current studies have neglected this effect. In this paper, statistical analyses were carried out in order to investigate the effect of uncertainties in the data and the impact of post-grouting on the bearing behaviors of bored piles. The results show that post-grouting can significantly improve the bearing behavior of piles. This study is expected to provide technical guidance for post-grouting in foundation engineering.
- Open Access
- 23 February 2023
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 82 (3) , 1-11
Direct measurement of unsaturated permeability of kaolin-sand mixtures
Unsaturated permeabilities of six different kaolin-sand mixtures named as 100K0S, 90K10S, 80K20S, 50K50S, 20K80S, and 10K90S were directly measured using a modified flexible wall triaxial permeameter system. 90K10S means that the soil mixture contains 90% kaolin and 10% sand by dry mass. Soil–water characteristic curves (SWCC) of the kaolin-sand soil mixtures were also measured for a wide range of suctions using a Tempe pressure cell, 5-bar pressure plate, 15-bar pressure plate, and saturated salt solutions. The unsaturated permeabilities of the soil mixtures were also estimated using ten different theoretical models using (1) the measured SWCC data over a complete suction range and (2) the measured SWCC data up to 100 kPa suction in combination with the estimated SWCC data at higher suction values. The directly measured unsaturated permeability of the soil mixtures was used to validate the estimated values of unsaturated permeability. The results showed that the unsaturated permeability estimation models could reasonably fit the directly measured unsaturated permeability data when both the data from the complete measurement of SWCC and the measured SWCC data up to 100 kPa suction in combination with the estimated SWCC data at higher suction values were used.
- 23 February 2023
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 82 (3) , 1-11
Open AccessDirect measurement of unsaturated permeability of kaolin-sand mixtures
Unsaturated permeabilities of six different kaolin-sand mixtures named as 100K0S, 90K10S, 80K20S, 50K50S, 20K80S, and 10K90S were directly measured using a modified flexible wall triaxial permeameter system. 90K10S means that the soil mixture contains 90% kaolin and 10% sand by dry mass. Soil–water characteristic curves (SWCC) of the kaolin-sand soil mixtures were also measured for a wide range of suctions using a Tempe pressure cell, 5-bar pressure plate, 15-bar pressure plate, and saturated salt solutions. The unsaturated permeabilities of the soil mixtures were also estimated using ten different theoretical models using (1) the measured SWCC data over a complete suction range and (2) the measured SWCC data up to 100 kPa suction in combination with the estimated SWCC data at higher suction values. The directly measured unsaturated permeability of the soil mixtures was used to validate the estimated values of unsaturated permeability. The results showed that the unsaturated permeability estimation models could reasonably fit the directly measured unsaturated permeability data when both the data from the complete measurement of SWCC and the measured SWCC data up to 100 kPa suction in combination with the estimated SWCC data at higher suction values were used.