Junqing Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Junqing Li has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Wei Liu
Dalian University of Technology
5 shared publications - Yang Zhang
School of Physics, Dalian University of Technology, Dalian, CHINA
5 shared publications - Yongkang Lu
State Key Laboratory of High-Performance Precision Manufacturing, Dalian University of Technology, Dalian, China
5 shared publications - Shouquan Sun
State Key Laboratory of High-Performance Precision Manufacturing, School of Mechanical Engineering, Dalian University of Technology, Dalian 116024, China
2 shared publications - Changxi Zhao
Beijing Spacecrafts, China Academy of Space Technology, Beijing 100094, China
1 shared publication - Jiacheng Cui
State Key Laboratory of High-Performance Precision Manufacturing, Dalian University of Technology, Dalian, China
1 shared publication
Latest Publications
- 8 August 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (8)
A dedicated sensing approach for structural thermoelastic displacement fields: demonstrated on a cantilever plate
Thermal deformation is a critical issue in thin-walled and plate-like structures. Accurate real-time sensing of thermoelastic displacement fields in such structures is essential for ensuring dimensional stability. However, existing shapesensing techniques are primarily designed for mechanically induced displacements and often fail when thermal loads dominate. To fill this gap, this paper proposes a dedicated sensing approach for structural thermoelastic displacement fields by cooperatively fusing prior knowledge with limited measurement data. First, starting with finite element modeling, the superposition principle of structural thermal responses is theoretically derived. Then, an estimator based on thermal mode superposition is presented to simultaneously recover the temperature, thermoelastic displacement, and thermal strain fields from limited sensor data. Finally, a cooperative measurement strategy based on hybrid modes is proposed, enabling multiple sensors to work together in field reconstruction. Simulation and experimental case studies on cantilever plates validated the underlying principles, demonstrating that the proposed estimator not only replicates the accuracy of finite element analysis but also achieves a fourfold improvement in computational efficiency. Moreover, its results show good agreement with measured data. Additionally, the paper compares the performance of different thermal mode construction methods, offering new insights with significant guiding value for engineering applications.
- 8 August 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (8)
A dedicated sensing approach for structural thermoelastic displacement fields: demonstrated on a cantilever plate
Thermal deformation is a critical issue in thin-walled and plate-like structures. Accurate real-time sensing of thermoelastic displacement fields in such structures is essential for ensuring dimensional stability. However, existing shapesensing techniques are primarily designed for mechanically induced displacements and often fail when thermal loads dominate. To fill this gap, this paper proposes a dedicated sensing approach for structural thermoelastic displacement fields by cooperatively fusing prior knowledge with limited measurement data. First, starting with finite element modeling, the superposition principle of structural thermal responses is theoretically derived. Then, an estimator based on thermal mode superposition is presented to simultaneously recover the temperature, thermoelastic displacement, and thermal strain fields from limited sensor data. Finally, a cooperative measurement strategy based on hybrid modes is proposed, enabling multiple sensors to work together in field reconstruction. Simulation and experimental case studies on cantilever plates validated the underlying principles, demonstrating that the proposed estimator not only replicates the accuracy of finite element analysis but also achieves a fourfold improvement in computational efficiency. Moreover, its results show good agreement with measured data. Additionally, the paper compares the performance of different thermal mode construction methods, offering new insights with significant guiding value for engineering applications.
- Open Access
- 12 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (12) , 2405
Online Sensing of Thermal Deformation in Complex Space Bulkheads Driven by Temperature Field Measurements
In the assembly of spacecraft cabins, the presence of uncertain and time-varying temperature environments can induce thermal deformation in bulkheads, potentially affecting dimensional stability. Online sensing of thermal deformation is critical for mitigating such risks. However, conventional finite element methods (FEMs) rely on cascading thermal and structural analyses, which suffer from inefficiency. To address this issue, we propose a methodology that integrates a physical model with a data-driven temperature field measurement technique, demonstrated through case studies involving a spacecraft porthole bulkhead. First, leveraging the geometric invariance of the bulkhead during assembly, a purely static FE model is established offline. Second, multi-point temperature measurements combined with Kriging estimation are employed to directly reconstruct the temperature field, circumventing the computationally intensive FEM-based thermal analysis process. Finally, by utilizing the precomputed inverse stiffness matrix and performing an online conversion from temperature to equivalent forces, thermal deformation is rapidly resolved. The numerical results demonstrate that the root-mean-square errors of the predicted full-field deformation are maintained at the micron level, with an average computation time of less than 0.14 s. Furthermore, a meticulously designed experiment was conducted, where the predicted thermal displacements of several key points showed good agreement with measurements by means of a laser tracker. This research provides a promising tool to achieve digital twinning of thermal deformation states for aerospace components.
- 12 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (12) , 2405
Open AccessOnline Sensing of Thermal Deformation in Complex Space Bulkheads Driven by Temperature Field Measurements
In the assembly of spacecraft cabins, the presence of uncertain and time-varying temperature environments can induce thermal deformation in bulkheads, potentially affecting dimensional stability. Online sensing of thermal deformation is critical for mitigating such risks. However, conventional finite element methods (FEMs) rely on cascading thermal and structural analyses, which suffer from inefficiency. To address this issue, we propose a methodology that integrates a physical model with a data-driven temperature field measurement technique, demonstrated through case studies involving a spacecraft porthole bulkhead. First, leveraging the geometric invariance of the bulkhead during assembly, a purely static FE model is established offline. Second, multi-point temperature measurements combined with Kriging estimation are employed to directly reconstruct the temperature field, circumventing the computationally intensive FEM-based thermal analysis process. Finally, by utilizing the precomputed inverse stiffness matrix and performing an online conversion from temperature to equivalent forces, thermal deformation is rapidly resolved. The numerical results demonstrate that the root-mean-square errors of the predicted full-field deformation are maintained at the micron level, with an average computation time of less than 0.14 s. Furthermore, a meticulously designed experiment was conducted, where the predicted thermal displacements of several key points showed good agreement with measurements by means of a laser tracker. This research provides a promising tool to achieve digital twinning of thermal deformation states for aerospace components.
- 10 January 2024
- Published by Elsevier in Precision Engineering
- Vol. 87, 67-78
Thermal error compensation in length inspection of large-scale aircraft spars in nonuniform temperature environments
- 10 January 2024
- Published by Elsevier in Precision Engineering
- Vol. 87, 67-78
Thermal error compensation in length inspection of large-scale aircraft spars in nonuniform temperature environments
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-11
Accurate Construction Method of Sensor Measurement Network System for In-Situ Manufacturing of Large Aerospace Component
Accurate tracking of key points (KPs) in large-scale aerospace component manufacturing has been a core technology. Sensor measurement network system (SMNS) is defined as the unified benchmark to realize global position of KPs for determining position and orientation of components. However, due to multiple uncertain interferences, it is difficult to ensure the accuracy and reliability of SMNS under site conditions. To address this problem, the paper proposes an accurate and systematic construction method of large SMNS considering multiple uncertain errors. Firstly, the invalid points are eliminated based on geometric similarity of common observed information. Then, a novel model parameter identification method of SMNS with subsection dynamic weights is proposed to unify observed data from individual measurement systems in the global coordinate system. Next, a multi-level uncertainty propagation model under the combined effect of model parameter uncertainty and measurement uncertainty is presented, and a weighted fusion method based on uncertainty is further developed to calculate fused point. Finally, to further improve overall accuracy of SMNS, a configuration optimization method based on genetic algorithm by minimizing overall uncertainty is proposed to determine configurations of measurement instruments in SMNS. The influence of a series of key factors on the SMNS accuracy is analyzed in detail. Experimental results show that compared with conventional methods, the average, root mean square and maximum of point positioning errors under site conditions are reduced by 14.55 %, 17.74 % and 17.70 %, respectively. The research provides good guides of accurate construction of SMNS for in-situ manufacturing of large aerospace components.
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-11
Accurate Construction Method of Sensor Measurement Network System for In-Situ Manufacturing of Large Aerospace Component
Accurate tracking of key points (KPs) in large-scale aerospace component manufacturing has been a core technology. Sensor measurement network system (SMNS) is defined as the unified benchmark to realize global position of KPs for determining position and orientation of components. However, due to multiple uncertain interferences, it is difficult to ensure the accuracy and reliability of SMNS under site conditions. To address this problem, the paper proposes an accurate and systematic construction method of large SMNS considering multiple uncertain errors. Firstly, the invalid points are eliminated based on geometric similarity of common observed information. Then, a novel model parameter identification method of SMNS with subsection dynamic weights is proposed to unify observed data from individual measurement systems in the global coordinate system. Next, a multi-level uncertainty propagation model under the combined effect of model parameter uncertainty and measurement uncertainty is presented, and a weighted fusion method based on uncertainty is further developed to calculate fused point. Finally, to further improve overall accuracy of SMNS, a configuration optimization method based on genetic algorithm by minimizing overall uncertainty is proposed to determine configurations of measurement instruments in SMNS. The influence of a series of key factors on the SMNS accuracy is analyzed in detail. Experimental results show that compared with conventional methods, the average, root mean square and maximum of point positioning errors under site conditions are reduced by 14.55 %, 17.74 % and 17.70 %, respectively. The research provides good guides of accurate construction of SMNS for in-situ manufacturing of large aerospace components.
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (7) , 7077-7086
Calibration of the Geometric Error Parameters of Laser Trackers in Site Environments
Laser trackers (LTs) are indispensable instruments in large-scale dimensional metrology. Nevertheless, geometric errors are prone to increase in site environments due to the occurrence of mechanical and optical misalignments, which deteriorates the measurement accuracy of the LT. The geometric error parameters are difficult to determine by traditional measuring or calibrating approaches. In this paper, a classification calibration method is proposed without any other etalons or instruments that accurately estimate the geometric error parameters in a site environment. First, to determine the environmental sensitivity error parameters, a refractive index correction model in a variable temperature environment is constructed, which performs well in reducing the interference of environmental temperature fluctuations. Subsequently, a spatial measurement network is established to determine two-face sensitivity error parameters using the difference between the frontsight and backsight measurements of the targets. Finally, the two-face non-sensitivity error parameters are solved by minimizing the residuals of the coordinate transformation from each LT station to the reference frame. Indeed, the effects of temperature fluctuation and geometrical misalignments on the measurement accuracy are deeply analyzed, which provide meaningful guidance for calibration and compensation of the geometric errors of the LT. The effectiveness of the proposed method is validated by a series of site experiments. The results show that the length error is reduced to 0.030mm on average, which is 44% lower than that of the network method.
- 23 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (7) , 7077-7086
Calibration of the Geometric Error Parameters of Laser Trackers in Site Environments
Laser trackers (LTs) are indispensable instruments in large-scale dimensional metrology. Nevertheless, geometric errors are prone to increase in site environments due to the occurrence of mechanical and optical misalignments, which deteriorates the measurement accuracy of the LT. The geometric error parameters are difficult to determine by traditional measuring or calibrating approaches. In this paper, a classification calibration method is proposed without any other etalons or instruments that accurately estimate the geometric error parameters in a site environment. First, to determine the environmental sensitivity error parameters, a refractive index correction model in a variable temperature environment is constructed, which performs well in reducing the interference of environmental temperature fluctuations. Subsequently, a spatial measurement network is established to determine two-face sensitivity error parameters using the difference between the frontsight and backsight measurements of the targets. Finally, the two-face non-sensitivity error parameters are solved by minimizing the residuals of the coordinate transformation from each LT station to the reference frame. Indeed, the effects of temperature fluctuation and geometrical misalignments on the measurement accuracy are deeply analyzed, which provide meaningful guidance for calibration and compensation of the geometric errors of the LT. The effectiveness of the proposed method is validated by a series of site experiments. The results show that the length error is reduced to 0.030mm on average, which is 44% lower than that of the network method.