Can Cui
Can Cui has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Alexander N. Stameroff
Keysight Technologies, Santa Rosa, CA, USA
2 shared publications- Anh-Vu Pham
Department of Electrical and Computer Engineering, University of California at Davis, Davis, CA, USA
2 shared publications - Nguyen L. K. Nguyen
Department of Electrical and Computer Engineering, University of California, Davis, CA, USA
2 shared publications - Anthony S. Pham
Department of Electrical and Computer Engineering, University of California, Davis, Davis, CA, USA
1 shared publication - Anton L. Geiler
LLG Associates
1 shared publication Brad Harris
Department of Electrical and Computer Engineering, University of California, Davis, CA, 95616, USA
1 shared publication
Latest Publications
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 27 (5) , 149-150
IMS2026 Student Design Competitions
Provides society information that may include news, reviews or technical notes that should be of interest to practitioners and researchers.
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 27 (5) , 149-150
IMS2026 Student Design Competitions
Provides society information that may include news, reviews or technical notes that should be of interest to practitioners and researchers.
- 6 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (1) , 285-297
A DC to 210 GHz InP Distributed Amplifier Using Gain Enhanced Cross-Configured Topology
This article presents a new eight-stage distributed amplifier (DA) based on a cross-configured architecture that employs two distinct types of gain cells to simultaneously achieve high gain and wide bandwidths. The first four stages utilize triple-stacked heterojunction bipolar transistors (HBTs) with input capacitive coupling (CC) technique, while the last four stages adopt triple-stacked HBTs with resistive-capacitive (RC) emitter degeneration. This cross-configured structure enhances the overall gain by approximately 2 dB across the operating frequency range without increasing power consumption and preserves the high-bandwidth characteristics of a traditional DA using the combined CC and RC techniques in each gain cell. A comprehensive analysis of gain and high-frequency performance is provided to support the design. The proposed DA is fabricated in an indium phosphide (InP) process that achieves 13 dB gain, 3-dB bandwidth from dc to 210 GHz, and 180 mW dc power consumption. The measured saturated output power ( ${P}_{\text {sat}}$ ) reaches a maximum of 14.9 dBm at 70 GHz and achieves 12.3 dBm at 175 GHz. To the best of the authors’ knowledge, this work presents the first cross-configured DA topology that leverages both CC and RC gain cells to simultaneously achieve high gain and wide bandwidth performance.
- 6 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (1) , 285-297
A DC to 210 GHz InP Distributed Amplifier Using Gain Enhanced Cross-Configured Topology
This article presents a new eight-stage distributed amplifier (DA) based on a cross-configured architecture that employs two distinct types of gain cells to simultaneously achieve high gain and wide bandwidths. The first four stages utilize triple-stacked heterojunction bipolar transistors (HBTs) with input capacitive coupling (CC) technique, while the last four stages adopt triple-stacked HBTs with resistive-capacitive (RC) emitter degeneration. This cross-configured structure enhances the overall gain by approximately 2 dB across the operating frequency range without increasing power consumption and preserves the high-bandwidth characteristics of a traditional DA using the combined CC and RC techniques in each gain cell. A comprehensive analysis of gain and high-frequency performance is provided to support the design. The proposed DA is fabricated in an indium phosphide (InP) process that achieves 13 dB gain, 3-dB bandwidth from dc to 210 GHz, and 180 mW dc power consumption. The measured saturated output power ( ${P}_{\text {sat}}$ ) reaches a maximum of 14.9 dBm at 70 GHz and achieves 12.3 dBm at 175 GHz. To the best of the authors’ knowledge, this work presents the first cross-configured DA topology that leverages both CC and RC gain cells to simultaneously achieve high gain and wide bandwidth performance.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 26 (6) , 176-186
IMS2025 Industry and Advanced Practice Paper Competitions
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 26 (6) , 176-186
IMS2025 Industry and Advanced Practice Paper Competitions
- Open Access
- 23 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 715-718
A 7–115-GHz Distributed Amplifier With 24-dBm Output Power Using Quadruple-Stacked HBT in InP
In this letter, we present the designs and development of a wideband, high output power quadruple-stacked heterojunction bipolar transistor (HBT) distributed amplifier (DA). In particular, the stacked HBT configuration can improve gain and output power while achieving a very wide bandwidth. To validate the proposed design concept, a quadruple-stacked HBT DA is designed in an indium phosphide (InP) process. The measurement results show an average gain of 16 dB from 7–115-GHz bandwidth with a maximum of 24-dBm saturated output power ( $P_{\mathrm{sat}})$ . To the best of the authors’ knowledge, this is the first time quadruple-stacked HBT is used in a DA to achieve the highest output power compared with other published work in the same frequency range.
- 23 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 715-718
Open AccessA 7–115-GHz Distributed Amplifier With 24-dBm Output Power Using Quadruple-Stacked HBT in InP
In this letter, we present the designs and development of a wideband, high output power quadruple-stacked heterojunction bipolar transistor (HBT) distributed amplifier (DA). In particular, the stacked HBT configuration can improve gain and output power while achieving a very wide bandwidth. To validate the proposed design concept, a quadruple-stacked HBT DA is designed in an indium phosphide (InP) process. The measurement results show an average gain of 16 dB from 7–115-GHz bandwidth with a maximum of 24-dBm saturated output power ( $P_{\mathrm{sat}})$ . To the best of the authors’ knowledge, this is the first time quadruple-stacked HBT is used in a DA to achieve the highest output power compared with other published work in the same frequency range.
- Open Access
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 170nW CMOS wake-up receiver with −60 dBm sensitivity using AlN high-Q piezoelectric resonators
A new wake-up receiver (WuRx) designed in 0.13 μm CMOS process is hybrid-integrated with a micro-electromechanical system (MEMS) RF resonator. While only consuming 166 nW of power (18.8 nW for the comparator and 147 nW for periphery), the WuRx is capable of detecting RF signals as weak as -60 dBm. In order to achieve this sensitivity, a passive voltage-boosting network comprised of a high quality factor (high-Q) piezoelectric MEMS resonator is utilized, in place of an inductor, to amplify the received voltages applied to a CMOS rectifier. The output of the rectifier is then applied to a low-power comparator used to set a logical bit that indicates when an RF signal has been detected. The trade-offs in designing the voltage boosting network are explained and an equation for the optimum number of rectifier stages is derived.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Open AccessA 170nW CMOS wake-up receiver with −60 dBm sensitivity using AlN high-Q piezoelectric resonators
A new wake-up receiver (WuRx) designed in 0.13 μm CMOS process is hybrid-integrated with a micro-electromechanical system (MEMS) RF resonator. While only consuming 166 nW of power (18.8 nW for the comparator and 147 nW for periphery), the WuRx is capable of detecting RF signals as weak as -60 dBm. In order to achieve this sensitivity, a passive voltage-boosting network comprised of a high quality factor (high-Q) piezoelectric MEMS resonator is utilized, in place of an inductor, to amplify the received voltages applied to a CMOS rectifier. The output of the rectifier is then applied to a low-power comparator used to set a logical bit that indicates when an RF signal has been detected. The trade-offs in designing the voltage boosting network are explained and an equation for the optimum number of rectifier stages is derived.