Yong Hyeon Yi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yong Hyeon Yi has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Chris H. Kim
Department of Electrical and Computer Engineering, University of Minnesota, Minneapolis, USA
4 shared publications - Alexander Volkov
Siemens EDA, Fremont, CA, USA
2 shared publications - Robert P. Bloom
University of Minnesota, Minneapolis, MN, USA
2 shared publications - Stephane Moreau
Univ. Grenoble Alpes, CEA, LETI, Grenoble, France
2 shared publications - Valeriy Sukharev
Siemens EDA, Fremont, CA, USA
2 shared publications Armen Kteyan
Siemens EDA, Yerevan, Armenia
1 shared publication
Latest Publications
- 23 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. PP (00189499) , 1
Observation of Higher Upset Rates in Multi-Bit Flip-Flops Utilized in Low Power Designs
Multi-bit flip-flops (MBFFs) are widely adopted in low-power digital designs due to their ability to reduce area and clock switching power by sharing clock buffers across multiple individual flip-flops. However, this clock resource sharing introduces new bit-upsets vulnerabilities in the form of single-event transients (SETs) within the shared clock buffer, distinct from standard storage-node single-event upset (SEU). This work presents neutron-induced soft error characterization results for MBFFs implemented with both standard and radiation-hardened dual interlocked storage cell (DICE) latches in a 0.9V, 28nm CMOS technology. Neutron irradiation experiment was conducted at the ChipIR facility in the Rutherford Appleton Laboratory, UK. A total of 84 test chips containing over 800,000 flip-flops were tested under multiple voltage conditions and data patterns. Upset mechanisms were classified into storage-node upsets, local clock buffer SETs, and global scan clock SETs. The results confirm that MBFFs, despite the use of DICE for hardened storage, exhibit significantly increased susceptibility to SETs in shared clock buffers. This study highlights an important trade-off between power efficiency and radiation resilience in multi-bit flip-flop designs, calling attention to the need for targeted mitigation strategies to ensure robust system operation in radiation prone environments.
- 23 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. PP (00189499) , 1
Observation of Higher Upset Rates in Multi-Bit Flip-Flops Utilized in Low Power Designs
Multi-bit flip-flops (MBFFs) are widely adopted in low-power digital designs due to their ability to reduce area and clock switching power by sharing clock buffers across multiple individual flip-flops. However, this clock resource sharing introduces new bit-upsets vulnerabilities in the form of single-event transients (SETs) within the shared clock buffer, distinct from standard storage-node single-event upset (SEU). This work presents neutron-induced soft error characterization results for MBFFs implemented with both standard and radiation-hardened dual interlocked storage cell (DICE) latches in a 0.9V, 28nm CMOS technology. Neutron irradiation experiment was conducted at the ChipIR facility in the Rutherford Appleton Laboratory, UK. A total of 84 test chips containing over 800,000 flip-flops were tested under multiple voltage conditions and data patterns. Upset mechanisms were classified into storage-node upsets, local clock buffer SETs, and global scan clock SETs. The results confirm that MBFFs, despite the use of DICE for hardened storage, exhibit significantly increased susceptibility to SETs in shared clock buffers. This study highlights an important trade-off between power efficiency and radiation resilience in multi-bit flip-flop designs, calling attention to the need for targeted mitigation strategies to ensure robust system operation in radiation prone environments.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (2) , 253-262
A Power Grid Electromigration Test Chip for Lifetime Characterization and Model Calibration
This work presents silicon data from 28 nm test chips specifically designed to study electromigration (EM) induced lifetime effects. The power grids were generated by an automatic place-and-route tool to create realistic device-under-tests (DUT) to capture power grid EM aging behaviors and lifetimes. Poly-silicon quasi-load cells mimicking the circuit current were employed to withstand high temperature stress. 1,024 local voltages throughout the power grid were tapped out to monitor the voiding locations and IR drop trends with stress. Four power grid architectures with different metal configurations were tested under different temperatures and currents. EM effects under different temperatures and current cycling conditions were also studied.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (2) , 253-262
A Power Grid Electromigration Test Chip for Lifetime Characterization and Model Calibration
This work presents silicon data from 28 nm test chips specifically designed to study electromigration (EM) induced lifetime effects. The power grids were generated by an automatic place-and-route tool to create realistic device-under-tests (DUT) to capture power grid EM aging behaviors and lifetimes. Poly-silicon quasi-load cells mimicking the circuit current were employed to withstand high temperature stress. 1,024 local voltages throughout the power grid were tapped out to monitor the voiding locations and IR drop trends with stress. Four power grid architectures with different metal configurations were tested under different temperatures and currents. EM effects under different temperatures and current cycling conditions were also studied.
- Open Access
- 26 March 2023
- Published by Association for Computing Machinery (ACM)
- p. 124-132
Electromigration Assessment in Power Grids with Account of Redundancy and Non-Uniform Temperature Distribution
- 26 March 2023
- Published by Association for Computing Machinery (ACM)
- p. 124-132
Open AccessElectromigration Assessment in Power Grids with Account of Redundancy and Non-Uniform Temperature Distribution
- 24 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (2) , 233-240
On-Chip Heater Design and Control Methodology for Reliability Testing Applications Requiring Over 300°C Local Temperatures
This paper presents the design details and control methodologies for on-chip heaters that can provide fast and accurate local temperature control for reliability testing applications. The on-chip heater uses the Joule heating effect of a metal or poly line to heat the surrounding devices-under-test (DUT) to a target temperature as high as 300∘C. Many generations of on-chip heaters, including different heater positions, heater areas, and heater layers, have been demonstrated in technology nodes from 350nm to 16nm. To accurately operate the heater and extend the heater’s operation lifetime for long-term reliability testing, we have also developed control methodologies for precise and reliable heater control.
- 24 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (2) , 233-240
On-Chip Heater Design and Control Methodology for Reliability Testing Applications Requiring Over 300°C Local Temperatures
This paper presents the design details and control methodologies for on-chip heaters that can provide fast and accurate local temperature control for reliability testing applications. The on-chip heater uses the Joule heating effect of a metal or poly line to heat the surrounding devices-under-test (DUT) to a target temperature as high as 300∘C. Many generations of on-chip heaters, including different heater positions, heater areas, and heater layers, have been demonstrated in technology nodes from 350nm to 16nm. To accurately operate the heater and extend the heater’s operation lifetime for long-term reliability testing, we have also developed control methodologies for precise and reliable heater control.