Wen-Liang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Wen-Liang Liu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Xiaohua Ma
Xidian University
5 shared publications - Yue Hao
Guangzhou Wide Bandgap Semiconductor Innovation Center, Guangzhou Institute of Technology, Xidian University 1 , Guangzhou 510555
5 shared publications - Chunzhou Shi
State Key Discipline Laboratory of Wide Band-gap Semiconductor Technology, School of Microelectronics, Xidian University, Xian, China
3 shared publications - Chupeng Yi
Xidian University
3 shared publications - Jing-Ya Deng
School of Physics, Xidian University, Xian, China
3 shared publications - Yang Lu
Xidian University
3 shared publications
Latest Publications
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 8879-8892
Class-F −1 Asymmetric Doherty Power Amplifier Integrated Slot Antenna Array With High Efficiency and Large Back-Off Range
This research proposes an asymmetric Doherty power amplifier integrated active antenna (ADPAIA) with high efficiency and large back-off range, integrating a Class-F−1 gallium nitride (GaN) monolithic microwave integrated circuit (MMIC) Doherty power amplifier (DPA) with an on PCB stub-loaded wide-slot antenna array (SLSAA). In this work, the phase difference and current ratio between the carrier and peaking amplifiers are meticulously designed. These parameters play a crucial role in determining both the impedance matrix of the DPA’s output network and its back-off range. Through fine-tuning these parameters, the fundamental impedance of the carrier and peaking amplifiers in the DPA at both peak power and output power back-off (OPBO) states can directly match the precisely tailored input impedance of the SLSAA, enabling a large back-off range. Unlike conventional DPA integrated antennas, where the active load modulation of the DPA is achieved through the output matching network (OMN) and power combiner network (PCN) of the DPA, the active load modulation in the ADPAIA is realized through spatial coupling of the SLSAA. Moreover, the harmonic impedances of the DPA are modulated by optimizing the dimensions of the SLSAA’s stubs. Consequently, the DPA’s OMN, PCN, and the harmonic control network (HCN), which are essential for traditional Class-F−1 DPAs’ integrated antennas but typically introduce unavoidable insertion loss, are eliminated for the first time. The fabricated ADPAIA demonstrates a maximum power-added efficiency (PAE) of 47.8% at peak power and 44.5% at 8-dB OPBO under continuous-wave signal testing across 4.5–4.9 GHz. These PAE results, along with the power back-off range, outperform the performance of previously reported integrated DPA antennas, which are essential for modern wireless communications.
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 8879-8892
Class-F −1 Asymmetric Doherty Power Amplifier Integrated Slot Antenna Array With High Efficiency and Large Back-Off Range
This research proposes an asymmetric Doherty power amplifier integrated active antenna (ADPAIA) with high efficiency and large back-off range, integrating a Class-F−1 gallium nitride (GaN) monolithic microwave integrated circuit (MMIC) Doherty power amplifier (DPA) with an on PCB stub-loaded wide-slot antenna array (SLSAA). In this work, the phase difference and current ratio between the carrier and peaking amplifiers are meticulously designed. These parameters play a crucial role in determining both the impedance matrix of the DPA’s output network and its back-off range. Through fine-tuning these parameters, the fundamental impedance of the carrier and peaking amplifiers in the DPA at both peak power and output power back-off (OPBO) states can directly match the precisely tailored input impedance of the SLSAA, enabling a large back-off range. Unlike conventional DPA integrated antennas, where the active load modulation of the DPA is achieved through the output matching network (OMN) and power combiner network (PCN) of the DPA, the active load modulation in the ADPAIA is realized through spatial coupling of the SLSAA. Moreover, the harmonic impedances of the DPA are modulated by optimizing the dimensions of the SLSAA’s stubs. Consequently, the DPA’s OMN, PCN, and the harmonic control network (HCN), which are essential for traditional Class-F−1 DPAs’ integrated antennas but typically introduce unavoidable insertion loss, are eliminated for the first time. The fabricated ADPAIA demonstrates a maximum power-added efficiency (PAE) of 47.8% at peak power and 44.5% at 8-dB OPBO under continuous-wave signal testing across 4.5–4.9 GHz. These PAE results, along with the power back-off range, outperform the performance of previously reported integrated DPA antennas, which are essential for modern wireless communications.
- 30 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (3) , 2486-2497
Class-F–1 GaN Power Amplifier Integrated Active Antenna With Increased Efficiency for Wireless Power Transmission Applications
This article introduces a novel power amplifier integrated active antenna (PAIAA) with increased efficiency that integrates a Class-$F {^{-}1 }$ Gallium Nitride (GaN) power amplifier (PA) and a stub-loaded wide slot antenna (SLSA) for wireless power transmission (WPT) applications. Unlike conventional PA integrated active antennas in which antennas and PAs are separately matched to 50 ohms, the input impedance of the SLSA is meticulously engineered to match the fundamental impedance and modulate harmonic impedances of the GaN transistor by optimizing the dimensions of the SLSA's stubs. This approach eliminates the output matching network (OMN), the PA's harmonic modulation network (HMN), and the antenna's input matching network (IMN), which typically incur unavoidable insertion loss but are essential for conventional Class-$F {^{-}1 }$ PAs and antennas. Consequently, it enhances the power-added efficiency (PAE) within the 3.3–3.8-GHz range and reduces the overall size of the PA integrated active antenna. Thanks to the extended design freedom offered by SLSA, precise impedance values can be achieved across a broader frequency range, resulting in increased efficiency across a larger spectrum. In addition, an innovative insertion loss measurement method for impedance matching network with a non-50-$\Omega $ port is introduced to accurately measure the Class-$F {^{-}1 }$ PA's PAE incorporated in the proposed PAIAA. The measured PAIAA demonstrates a peak PAE of 70.1%, surpassing the performances of reported integrated active antennas. The measured effective isotropic radiated power (EIRP) of the proposed PAIAA is 44.52 dBm. A conventional PA-antenna design, where an antenna and a Class-$F {^{-}1 }$ PA are separately matched to$50~\Omega $ and simply cascaded, is also designed and measured as a contrast, whose measured peak PAE and EIRP of the conventional design are only 61.5% and 43.9 dBm, respectively. The proposed PAIAA, with its increased efficiency, can be practically utilized for WPT applications in the Internet of Things (IoT), where efficiency performance is critical.- 30 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (3) , 2486-2497
Class-F–1 GaN Power Amplifier Integrated Active Antenna With Increased Efficiency for Wireless Power Transmission Applications
This article introduces a novel power amplifier integrated active antenna (PAIAA) with increased efficiency that integrates a Class-$F {^{-}1 }$ Gallium Nitride (GaN) power amplifier (PA) and a stub-loaded wide slot antenna (SLSA) for wireless power transmission (WPT) applications. Unlike conventional PA integrated active antennas in which antennas and PAs are separately matched to 50 ohms, the input impedance of the SLSA is meticulously engineered to match the fundamental impedance and modulate harmonic impedances of the GaN transistor by optimizing the dimensions of the SLSA's stubs. This approach eliminates the output matching network (OMN), the PA's harmonic modulation network (HMN), and the antenna's input matching network (IMN), which typically incur unavoidable insertion loss but are essential for conventional Class-$F {^{-}1 }$ PAs and antennas. Consequently, it enhances the power-added efficiency (PAE) within the 3.3–3.8-GHz range and reduces the overall size of the PA integrated active antenna. Thanks to the extended design freedom offered by SLSA, precise impedance values can be achieved across a broader frequency range, resulting in increased efficiency across a larger spectrum. In addition, an innovative insertion loss measurement method for impedance matching network with a non-50-$\Omega $ port is introduced to accurately measure the Class-$F {^{-}1 }$ PA's PAE incorporated in the proposed PAIAA. The measured PAIAA demonstrates a peak PAE of 70.1%, surpassing the performances of reported integrated active antennas. The measured effective isotropic radiated power (EIRP) of the proposed PAIAA is 44.52 dBm. A conventional PA-antenna design, where an antenna and a Class-$F {^{-}1 }$ PA are separately matched to$50~\Omega $ and simply cascaded, is also designed and measured as a contrast, whose measured peak PAE and EIRP of the conventional design are only 61.5% and 43.9 dBm, respectively. The proposed PAIAA, with its increased efficiency, can be practically utilized for WPT applications in the Internet of Things (IoT), where efficiency performance is critical.- Open Access
- 13 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 39-45
The Dual-Mode Integration of Power Amplifier and Radio Frequency Switch Based on GaN Dual-Gate HEMTs
In this paper, an integrated device which realized the dual-mode integration of power amplifier (PA) and radio frequency (RF) switch based on GaN dual-gate (DG) structure is designed and fabricated. The integrated device provides two working modes and meets the performance requirements of PA and RF switch. In the transmit (Tx) mode, the integrated device is used as PA. At the frequency of 3.6 GHz, compared with the conventional GaN HEMT (high electron mobility transistor) as PA, due to the field modulation effect of the dual-gate structure, the current collapse is effectively suppressed, and the output power density (Pout) of the integrated device is increased from 6.90 W/mm to 7.85 W/mm, and the power added efficiency (PAE) is increased from 44.3% to 51.1%. In the receive (Rx) mode, the integrated device is used as RF switch. Compared with conventional RF switch, the isolation of integrated devices is significantly improved. At the frequency of 3.6GHz, the isolation is improved from 19.4 dB to 41.0 dB; At the frequency of 40 GHz, the isolation is improved from 3.0 dB to 29.7 dB. The integrated device provides a novel function integration scheme for RF frontends, with great potential for improving the integration and dimension of future communication systems.
- 13 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 39-45
Open AccessThe Dual-Mode Integration of Power Amplifier and Radio Frequency Switch Based on GaN Dual-Gate HEMTs
In this paper, an integrated device which realized the dual-mode integration of power amplifier (PA) and radio frequency (RF) switch based on GaN dual-gate (DG) structure is designed and fabricated. The integrated device provides two working modes and meets the performance requirements of PA and RF switch. In the transmit (Tx) mode, the integrated device is used as PA. At the frequency of 3.6 GHz, compared with the conventional GaN HEMT (high electron mobility transistor) as PA, due to the field modulation effect of the dual-gate structure, the current collapse is effectively suppressed, and the output power density (Pout) of the integrated device is increased from 6.90 W/mm to 7.85 W/mm, and the power added efficiency (PAE) is increased from 44.3% to 51.1%. In the receive (Rx) mode, the integrated device is used as RF switch. Compared with conventional RF switch, the isolation of integrated devices is significantly improved. At the frequency of 3.6GHz, the isolation is improved from 19.4 dB to 41.0 dB; At the frequency of 40 GHz, the isolation is improved from 3.0 dB to 29.7 dB. The integrated device provides a novel function integration scheme for RF frontends, with great potential for improving the integration and dimension of future communication systems.
- Top Cited Papers
- 3 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (5) , 2241-2246
High-Efficiency AlGaN/GaN/Graded-AlGaN/GaN Double-Channel HEMTs for Sub-6G Power Amplifier Applications
In this article, the superior power performance of a double-channel high-electron-mobility transistor (HEMT) operating at a high drain voltage of sub-6 GHz was demonstrated using a heterostructure of Al $_{\text{0}.\text{3}}$ Ga $_{\text{0}.\text{7}}$ N/GaN/Al $_{\textit{x}}$ Ga $_{\text{1}-\textit{x}}$ N/GaN, $\textit{x}$ ranging from 0.3 to 0, top-down double channel with graded barrier HEMT (DCGB-HEMT). In comparison to single channel HEMT (SC-HEMT), DCGB-HEMT exhibits superior direct current (dc) characteristics, including a wider gate voltage swing, a higher saturation current (up to 1307.80 mA/mm), and a higher OFF-state breakdown voltage (up to 165 V). Through TCAD simulation, the breakdown voltage was increased because the graded barrier reduces the peak value of the electric field at the gate’s edge on the drain side. Compared to SC-HEMT, DCGB-HEMT’s current collapse (CC) decreased from 23.35% to 9.82%. Electrons from the upper channel are more effectively prevented from being captured by acceptors in a buffer induced by Fe-doping by a thicker 3-D electron gas (3DEG) forming between the bottom channel and graded bottom barrier, prevailing over a thinner 2-D electron gas (2DEG). DCGB-HEMT’s maximum power-added efficiency (PAE) increased from 56% to 70.4%. DCGB-HEMTs exhibit superior PAE due to their improved gate control, lower leakage, and improved CC at high drain voltage.
- 3 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (5) , 2241-2246
Top Cited PapersHigh-Efficiency AlGaN/GaN/Graded-AlGaN/GaN Double-Channel HEMTs for Sub-6G Power Amplifier Applications
In this article, the superior power performance of a double-channel high-electron-mobility transistor (HEMT) operating at a high drain voltage of sub-6 GHz was demonstrated using a heterostructure of Al $_{\text{0}.\text{3}}$ Ga $_{\text{0}.\text{7}}$ N/GaN/Al $_{\textit{x}}$ Ga $_{\text{1}-\textit{x}}$ N/GaN, $\textit{x}$ ranging from 0.3 to 0, top-down double channel with graded barrier HEMT (DCGB-HEMT). In comparison to single channel HEMT (SC-HEMT), DCGB-HEMT exhibits superior direct current (dc) characteristics, including a wider gate voltage swing, a higher saturation current (up to 1307.80 mA/mm), and a higher OFF-state breakdown voltage (up to 165 V). Through TCAD simulation, the breakdown voltage was increased because the graded barrier reduces the peak value of the electric field at the gate’s edge on the drain side. Compared to SC-HEMT, DCGB-HEMT’s current collapse (CC) decreased from 23.35% to 9.82%. Electrons from the upper channel are more effectively prevented from being captured by acceptors in a buffer induced by Fe-doping by a thicker 3-D electron gas (3DEG) forming between the bottom channel and graded bottom barrier, prevailing over a thinner 2-D electron gas (2DEG). DCGB-HEMT’s maximum power-added efficiency (PAE) increased from 56% to 70.4%. DCGB-HEMTs exhibit superior PAE due to their improved gate control, lower leakage, and improved CC at high drain voltage.
- 2 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (3) , 331-334
High Linear and Temperature Insensitive GaAs Power Amplifier Operating at 3.3–3.6 GHz Using a Multi-Feedback Branch Bias Circuit
This letter describes a design of a 3.3–3.6-GHz GaAs heterojunction bipolar transistor (HBT) power amplifier (PA) with high linearity and temperature insensitivity for the fifth-generation (5G) of new radios (NRs). By involving a multi-feedback branches bias circuit, the voltage at the feedback node of the bias circuit can achieve dynamic self-tuning to stabilize the base voltage as the amplifier’s input power grows and stabilize the bias current as the temperature increases as well. A three-stage common source structure PA in the form of a monolithic microwave integrated circuit (MMIC) is designed using a multi-feedback branch bias circuit with a size of 1.5 $\times$ 1.2 mm. Measured with continuous wave (CW) signals, the output 1-dB compression point at 3.3–3.6 GHz is 34 dBm. The linearity of the PA is also evaluated using a 5G-NR 100-MHz 64-quadratic-amplitude modulated (QAM)-orthogonal frequency division multiplexing (OFDM) signal with a 7-dB peak-to-average-power ratio (PAPR). The proposed PA achieves an adjacent channel power ratio (ACPR) less than $-$ 49.5 dBc at an average power of 28 dBm with a power-added efficiency (PAE) of 20% without the use of digital pre-distortion (DPD). In the temperature range of $-$ 40 $^{\circ}$ C to 120 $^{\circ}$ C, the variance of bias current, small signal gain, PAE, output power at 1-dB compression point (OP1dB), and ACPR is relatively minor. This design is ideally suited for 5G communication systems due to its high linearity and temperature insensitivity.
- 2 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (3) , 331-334
High Linear and Temperature Insensitive GaAs Power Amplifier Operating at 3.3–3.6 GHz Using a Multi-Feedback Branch Bias Circuit
This letter describes a design of a 3.3–3.6-GHz GaAs heterojunction bipolar transistor (HBT) power amplifier (PA) with high linearity and temperature insensitivity for the fifth-generation (5G) of new radios (NRs). By involving a multi-feedback branches bias circuit, the voltage at the feedback node of the bias circuit can achieve dynamic self-tuning to stabilize the base voltage as the amplifier’s input power grows and stabilize the bias current as the temperature increases as well. A three-stage common source structure PA in the form of a monolithic microwave integrated circuit (MMIC) is designed using a multi-feedback branch bias circuit with a size of 1.5 $\times$ 1.2 mm. Measured with continuous wave (CW) signals, the output 1-dB compression point at 3.3–3.6 GHz is 34 dBm. The linearity of the PA is also evaluated using a 5G-NR 100-MHz 64-quadratic-amplitude modulated (QAM)-orthogonal frequency division multiplexing (OFDM) signal with a 7-dB peak-to-average-power ratio (PAPR). The proposed PA achieves an adjacent channel power ratio (ACPR) less than $-$ 49.5 dBc at an average power of 28 dBm with a power-added efficiency (PAE) of 20% without the use of digital pre-distortion (DPD). In the temperature range of $-$ 40 $^{\circ}$ C to 120 $^{\circ}$ C, the variance of bias current, small signal gain, PAE, output power at 1-dB compression point (OP1dB), and ACPR is relatively minor. This design is ideally suited for 5G communication systems due to its high linearity and temperature insensitivity.