Rafael Iosifivich Shakirzyanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rafael Iosifivich Shakirzyanov has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Daryn B. Borgekov
The Institute of Nuclear Physics, Ibragimov Str. 1, Almaty 050032, Kazakhstan
11 shared publications - Dmitriy Igorevich Shlimas
Laboratory of Solid State Physics, The Institute of Nuclear Physics, Almaty 050032, Kazakhstan
11 shared publications - Artem Leonidovich Kozlovskiy
Engineering Profile Laboratory, L.N. Gumilyov Eurasian National University, Nur-Sultan 010000, Kazakhstan
10 shared publications - Yuriy Alexsandrovich Garanin
Engineering Profile Laboratory, L.N. Gumilyov Eurasian National University, Satpayev St., Astana 010008, Kazakhstan
10 shared publications - Natalia O. Volodina
Engineering Profile Laboratory, L.N. Gumilyov Eurasian National University, Astana 010008, Kazakhstan
8 shared publications - Malik Erlanovich Kaliyekperov
Engineering Profile Laboratory, L.N. Gumilyov Eurasian National University, Satpayev St., Astana 010008, Kazakhstan
6 shared publications
Latest Publications
- Open Access
- 30 October 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (11) , 583
Study of Frequency Dispersion of Permeability in PVDF/Ni0.4Zn0.6Fe2O4 Composites and Its Influence on Microwave Absorption Characteristics
Often, when describing the electromagnetic properties of polymer composites in the microwave range, little attention is paid to magnetic spectra and the description of their features using known dispersion models. In this paper, we investigate the microstructure and frequency spectra of the complex permittivity and complex permeability of the ferrite-polymer composite PVDF/Ni0.4Zn0.6Fe2O4 in the frequency range of 100 MHz–5 GHz and a mass concentration of 10–80 wt.%. The composite structure was investigated by scanning electron microscopy, while the frequency dependences of permittivity and magnetic permeability were measured using a vector network analyzer together with the Nicholson–Ross–Weir method. In the course of the work, using the fitting of the experimental spectra by known models of natural ferromagnetic resonance and domain wall resonance, the features of the dispersion of the magnetic spectra were explained. In particular, the shift of resonance frequency and the dominant contribution of spin rotation to the permeability value were interpreted using the results of fitting. In addition, comparison of the features of the reflection loss spectra and the results of model fitting helped to identify the main contribution of the spin rotation process to the attenuation of the electromagnetic wave in composites. The results obtained in the work are relevant for the development of new approaches to predicting the electromagnetic characteristics of composites using effective medium models.
- 30 October 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (11) , 583
Open AccessStudy of Frequency Dispersion of Permeability in PVDF/Ni0.4Zn0.6Fe2O4 Composites and Its Influence on Microwave Absorption Characteristics
Often, when describing the electromagnetic properties of polymer composites in the microwave range, little attention is paid to magnetic spectra and the description of their features using known dispersion models. In this paper, we investigate the microstructure and frequency spectra of the complex permittivity and complex permeability of the ferrite-polymer composite PVDF/Ni0.4Zn0.6Fe2O4 in the frequency range of 100 MHz–5 GHz and a mass concentration of 10–80 wt.%. The composite structure was investigated by scanning electron microscopy, while the frequency dependences of permittivity and magnetic permeability were measured using a vector network analyzer together with the Nicholson–Ross–Weir method. In the course of the work, using the fitting of the experimental spectra by known models of natural ferromagnetic resonance and domain wall resonance, the features of the dispersion of the magnetic spectra were explained. In particular, the shift of resonance frequency and the dominant contribution of spin rotation to the permeability value were interpreted using the results of fitting. In addition, comparison of the features of the reflection loss spectra and the results of model fitting helped to identify the main contribution of the spin rotation process to the attenuation of the electromagnetic wave in composites. The results obtained in the work are relevant for the development of new approaches to predicting the electromagnetic characteristics of composites using effective medium models.
- Open Access
Effect of Sintering Temperature on the Microstructure and Mechanical Properties of Multidoped Zirconia-Toughened Alumina
In this study, the effect of sintering temperature on the phase composition, density, microstructure, and mechanical properties of multidoped zirconia-toughened alumina (MZTA) ceramics containing multidoped zirconia (Zr0.90(Y, Ce, Ca, Mg)0.10O2) was investigated. The samples were fabricated using a conventional ceramic processing and sintered at temperatures ranging from 1400 to 1600 °C for 5 h. X-ray diffraction and whole-powder-pattern fitting (WPPF) analysis showed that, regardless of the sintering temperature, the samples consisted predominantly of t-ZrO2 and Al2O3 phases, with a minor (0.7–2.8 wt. %) amount of m-ZrO2 detected at certain temperatures. Scanning electron microscopy revealed that increasing the sintering temperature from 1400 to 1600 °C resulted in an increase in the average Al2O3 grain size from 0.39 to 1.32 µm and the ZrO2 grain size from 0.28 to 0.92 µm. The sample sintered at 1500 °C exhibited the best combination of microhardness (HV5 1748) and flexural strength (620 MPa), owing to its high density and homogeneous microstructure. At higher sintering temperatures, abnormal grain growth accompanied by a decrease in density was observed, resulting in a reduction in flexural strength. The fracture toughness (KIC) showed an approximately linear increase with increasing sintering temperature.
Open AccessEffect of Sintering Temperature on the Microstructure and Mechanical Properties of Multidoped Zirconia-Toughened Alumina
In this study, the effect of sintering temperature on the phase composition, density, microstructure, and mechanical properties of multidoped zirconia-toughened alumina (MZTA) ceramics containing multidoped zirconia (Zr0.90(Y, Ce, Ca, Mg)0.10O2) was investigated. The samples were fabricated using a conventional ceramic processing and sintered at temperatures ranging from 1400 to 1600 °C for 5 h. X-ray diffraction and whole-powder-pattern fitting (WPPF) analysis showed that, regardless of the sintering temperature, the samples consisted predominantly of t-ZrO2 and Al2O3 phases, with a minor (0.7–2.8 wt. %) amount of m-ZrO2 detected at certain temperatures. Scanning electron microscopy revealed that increasing the sintering temperature from 1400 to 1600 °C resulted in an increase in the average Al2O3 grain size from 0.39 to 1.32 µm and the ZrO2 grain size from 0.28 to 0.92 µm. The sample sintered at 1500 °C exhibited the best combination of microhardness (HV5 1748) and flexural strength (620 MPa), owing to its high density and homogeneous microstructure. At higher sintering temperatures, abnormal grain growth accompanied by a decrease in density was observed, resulting in a reduction in flexural strength. The fracture toughness (KIC) showed an approximately linear increase with increasing sintering temperature.
- 30 September 2026
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Physics & Mathematics series
- No. 3,2026
ИССЛЕДОВАНИЕ РАДИОПОГЛОЩАЮЩИХ МАТЕРИАЛОВ В МИЛЛИМЕТРОВОМ ДИАПАЗОНЕ
В данной работе представлены результаты исследования радиопоглощающих материалов в сверхвысокочастотном диапазоне 80-120 ГГц. В качестве основного радиопоглощающего материала рассмотрен порошок графита кристаллического типа. Подготовка материала осуществлялась путем перемешивания частиц графита определенной размерности с эпоксидной смолой. Частицы графита используются в качестве наполнителей в исследуемых материалах. Выбор объекта исследования не случаен, так как исследования радиофизических параметров графита показали перспективность его применения в качестве наполнителей. В качестве подложки и связующего материала использована эпоксидная смола. Образцы готовились путем продувки порошка по поверхности подложки из эпоксидной смолы. Экспериментальным путем установлена наиболее эффективная рабочая толщина эпоксидной смолы. Рассчитаны геометрические размеры расположения компонентов установки, при котором наблюдается наиболее эффективная регистрация сигнала. Результаты исследований показали, что пленка, состоящая из частиц графита на поверхности эпоксидной смолы, эффективно экранирует радиоизлучение в субмиллиметровом диапазоне. Полученный материал полностью соответствует необходимым критериям, а именно: «высокая эффективность защиты – невысокие затраты на изготовление». Получение радиопоглощающих материалов полностью соответствует целям устойчивого развития инфраструктуры телекоммуникаций и инноваций в этой области. Ключевые слова: Радиопоглощающие материалы, электромагнитное излучение, графит, сверхвысокая частота, эпоксидная смола.
- 30 September 2026
- Published by Toraighyrov University in Bulletin of Toraighyrov University. Physics & Mathematics series
- No. 3,2026
ИССЛЕДОВАНИЕ РАДИОПОГЛОЩАЮЩИХ МАТЕРИАЛОВ В МИЛЛИМЕТРОВОМ ДИАПАЗОНЕ
В данной работе представлены результаты исследования радиопоглощающих материалов в сверхвысокочастотном диапазоне 80-120 ГГц. В качестве основного радиопоглощающего материала рассмотрен порошок графита кристаллического типа. Подготовка материала осуществлялась путем перемешивания частиц графита определенной размерности с эпоксидной смолой. Частицы графита используются в качестве наполнителей в исследуемых материалах. Выбор объекта исследования не случаен, так как исследования радиофизических параметров графита показали перспективность его применения в качестве наполнителей. В качестве подложки и связующего материала использована эпоксидная смола. Образцы готовились путем продувки порошка по поверхности подложки из эпоксидной смолы. Экспериментальным путем установлена наиболее эффективная рабочая толщина эпоксидной смолы. Рассчитаны геометрические размеры расположения компонентов установки, при котором наблюдается наиболее эффективная регистрация сигнала. Результаты исследований показали, что пленка, состоящая из частиц графита на поверхности эпоксидной смолы, эффективно экранирует радиоизлучение в субмиллиметровом диапазоне. Полученный материал полностью соответствует необходимым критериям, а именно: «высокая эффективность защиты – невысокие затраты на изготовление». Получение радиопоглощающих материалов полностью соответствует целям устойчивого развития инфраструктуры телекоммуникаций и инноваций в этой области. Ключевые слова: Радиопоглощающие материалы, электромагнитное излучение, графит, сверхвысокая частота, эпоксидная смола.
- Open Access
- 30 September 2026
- Published by L. N. Gumilyov Eurasian National University in BULLETIN of the L.N. Gumilyov Eurasian National University. Physics. Astronomy Series
- Vol. 156 (3) , 97-114
Исследование диэлектрических характеристик термопластов ПВДФ, СКФ32, ПВС и ПС525 в микроволновом диапазоне
Актуальными являются экспериментальные исследования по получению частотных зависимостей диэлектрической проницаемости термопластов в микроволновом диапазоне, ввиду их использования в качестве матриц дисперсно-наполненных композитов. Целью настоящей работы является подбор технологических параметров для получения монолитных образцов некоторых широко используемых термопластов и измерение частотной зависимости комплексной диэлектрической проницаемости в диапазоне 100 МГц – 5 ГГц. В качестве объектов исследования были использованы поливинилиденфторид, фторкаучук поли(трифторхлорэтилен-винилиденфторид), поливиниловый спирт и полистирол. Образцы изготавливались методом горячего прессования на экспериментальном стенде при индивидуально подобранных значениях температуры выдержки, рабочего давления и времени выдержки, обеспечивающих получение монолитных изделий без визуально наблюдаемой пористости и внутренних дефектов. Частотные спектры комплексной диэлектрической проницаемости были измерены с помощью метода Николсона-Росса-Вира при комнатной температуре с использованием векторного анализатора цепей. В ходе проведения экспериментов обнаружено, что режимы термопрессования для используемых термопластов существенно различаются. При получении колец из поливинилового спирта наблюдалось пожелтение образцов, предположительно связанное с начальными стадиями термической деструкции материала. В диапазоне частот 100 МГц–5 ГГц действительная часть диэлектрической проницаемости ε’ для поливнилиденфторида составила 2,57–3,31, для фторкаучука — 2,40–3,16, для поливинилового спирта — 3,61–4,63. В случае полистирола значение ε’ в исследуемом диапазоне составило 2.64. Для всех полимеров кроме полистирола обнаружена выраженная частотная дисперсия комплексной диэлектрической проницаемости, а также диэлектрические потери в диапазоне 0,05–0,20. Помимо этого, рассчитанное значение коэффициента отражения на металлической пластине составляло от –4 до –2,5 дБ для термопластов с выраженными диэлектрическими потерями. Полученные частотные зависимости дополняют сведения о диэлектрических характеристиках распространенных термопластов в микроволновом диапазоне частот и могут быть использованы при разработке полимерных композиционных материалов с заданными диэлектрическими характеристиками для изделий радиоэлектроники, СВЧ-техники и радиопоглощающих материалов.
- 30 September 2026
- Published by L. N. Gumilyov Eurasian National University in BULLETIN of the L.N. Gumilyov Eurasian National University. Physics. Astronomy Series
- Vol. 156 (3) , 97-114
Open AccessИсследование диэлектрических характеристик термопластов ПВДФ, СКФ32, ПВС и ПС525 в микроволновом диапазоне
Актуальными являются экспериментальные исследования по получению частотных зависимостей диэлектрической проницаемости термопластов в микроволновом диапазоне, ввиду их использования в качестве матриц дисперсно-наполненных композитов. Целью настоящей работы является подбор технологических параметров для получения монолитных образцов некоторых широко используемых термопластов и измерение частотной зависимости комплексной диэлектрической проницаемости в диапазоне 100 МГц – 5 ГГц. В качестве объектов исследования были использованы поливинилиденфторид, фторкаучук поли(трифторхлорэтилен-винилиденфторид), поливиниловый спирт и полистирол. Образцы изготавливались методом горячего прессования на экспериментальном стенде при индивидуально подобранных значениях температуры выдержки, рабочего давления и времени выдержки, обеспечивающих получение монолитных изделий без визуально наблюдаемой пористости и внутренних дефектов. Частотные спектры комплексной диэлектрической проницаемости были измерены с помощью метода Николсона-Росса-Вира при комнатной температуре с использованием векторного анализатора цепей. В ходе проведения экспериментов обнаружено, что режимы термопрессования для используемых термопластов существенно различаются. При получении колец из поливинилового спирта наблюдалось пожелтение образцов, предположительно связанное с начальными стадиями термической деструкции материала. В диапазоне частот 100 МГц–5 ГГц действительная часть диэлектрической проницаемости ε’ для поливнилиденфторида составила 2,57–3,31, для фторкаучука — 2,40–3,16, для поливинилового спирта — 3,61–4,63. В случае полистирола значение ε’ в исследуемом диапазоне составило 2.64. Для всех полимеров кроме полистирола обнаружена выраженная частотная дисперсия комплексной диэлектрической проницаемости, а также диэлектрические потери в диапазоне 0,05–0,20. Помимо этого, рассчитанное значение коэффициента отражения на металлической пластине составляло от –4 до –2,5 дБ для термопластов с выраженными диэлектрическими потерями. Полученные частотные зависимости дополняют сведения о диэлектрических характеристиках распространенных термопластов в микроволновом диапазоне частот и могут быть использованы при разработке полимерных композиционных материалов с заданными диэлектрическими характеристиками для изделий радиоэлектроники, СВЧ-техники и радиопоглощающих материалов.
- 30 September 2026
- Published by International Journal of Technology in International Journal of Technology
- Vol. 17 (5) , 1780
Annealed-Induced Recrystallization and Phase Evolution in Indented Magnesia-Stabilized Zirconia Ceramics
Ceramic components are often subjected to mechanical loads and high temperatures during operation, which can lead to the accumulation of residual stresses, formation of various types of defects, and initiation of phase transformations. Although the individual effects of mechanical stresses or high temperatures on ceramic materials have been extensively studied, the material’s behavior under their sequential application, for example, during the annealing of previously deformed (indented) regions, remains of particular interest. The repeated annealing of ceramics can induce recrystallization processes, whose characteristics can differ significantly in previously stressed regions compared with undamaged regions of the material owing to the increased defect density and high concentration of local stresses. Partially stabilized Mg-doped ZrO2 ceramics have attracted considerable attention owing to their complex, composite-like structure, in which tetragonal grains are embedded in a cubic matrix. This microstructure provides high mechanical strength to the ceramics; however, this multiphase structure may be less stable under mechanical loading and heating. The influence of residual stresses and defects on recrystallization during annealing should be studied. In this study, Raman spectroscopy was used to investigate local phase evolution in indentation sites following recrystallization induced by annealing. Indentation was found to cause only a slight decrease in the fraction of the tetragonal ZrO2 phase and localized structural disorder at the center of the indentation site, where the stress concentration is highest. After annealing at 1000°C, the tetragonal phase fraction returned to its initial value. In contrast, annealing at 1100°C and 1200°C promoted the transformation of the cubic phase into the monoclinic phase and significant grain growth. This result indicates a metastable phase state after sintering and highlights the importance of assessing the phase stability of OCs under additional thermal and mechanical stresses.
- 30 September 2026
- Published by International Journal of Technology in International Journal of Technology
- Vol. 17 (5) , 1780
Annealed-Induced Recrystallization and Phase Evolution in Indented Magnesia-Stabilized Zirconia Ceramics
Ceramic components are often subjected to mechanical loads and high temperatures during operation, which can lead to the accumulation of residual stresses, formation of various types of defects, and initiation of phase transformations. Although the individual effects of mechanical stresses or high temperatures on ceramic materials have been extensively studied, the material’s behavior under their sequential application, for example, during the annealing of previously deformed (indented) regions, remains of particular interest. The repeated annealing of ceramics can induce recrystallization processes, whose characteristics can differ significantly in previously stressed regions compared with undamaged regions of the material owing to the increased defect density and high concentration of local stresses. Partially stabilized Mg-doped ZrO2 ceramics have attracted considerable attention owing to their complex, composite-like structure, in which tetragonal grains are embedded in a cubic matrix. This microstructure provides high mechanical strength to the ceramics; however, this multiphase structure may be less stable under mechanical loading and heating. The influence of residual stresses and defects on recrystallization during annealing should be studied. In this study, Raman spectroscopy was used to investigate local phase evolution in indentation sites following recrystallization induced by annealing. Indentation was found to cause only a slight decrease in the fraction of the tetragonal ZrO2 phase and localized structural disorder at the center of the indentation site, where the stress concentration is highest. After annealing at 1000°C, the tetragonal phase fraction returned to its initial value. In contrast, annealing at 1100°C and 1200°C promoted the transformation of the cubic phase into the monoclinic phase and significant grain growth. This result indicates a metastable phase state after sintering and highlights the importance of assessing the phase stability of OCs under additional thermal and mechanical stresses.
- Open Access
- 22 September 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (3) , 434-447
EFFECT OF TANTALUM AND VANADIUM CARBIDE DOPANTS ON THE STRUCTURE AND MECHANICAL PROPERTIES OF ALUMINUM NITRIDE-BASED CERAMICS
This work investigates the effect of tantalum carbide and vanadium carbide additions on the phase composition, microstructure, and mechanical properties of AlN-based ceramic composites synthesized by mechanochemical solid-state processing followed by thermal treatment. The molar fraction of the carbide additives was varied within the range of x = 0.01-0.10. Scanning electron microscopy combined with energy-dispersive X-ray spectroscopy revealed a homogeneous distribution of the reinforcing phases after mechanochemical activation. X-ray diffraction analysis showed that TaC remained chemically stable during processing, leading to the formation of a two-phase AlN-TaC composite with reduced lattice distortions of the AlN matrix. In contrast, VC underwent partial oxidation during heat treatment, resulting in the formation of secondary V 2 O 5 and a different phase evolution. Mechanochemical processing produced a more homogeneous powder morphology and suppressed the formation of large carbide agglomerates, providing favorable conditions for subsequent microstructural development. Mechanical testing demonstrated that a pronounced improvement in hardness and flexural strength occurred at dopant contents above x = 0.03, with the greatest strengthening effect observed for the TaC-containing composites owing to the retention of a stable, uniformly dispersed high-hardness carbide phase. The enhanced mechanical performance is attributed to the combined effects of dispersion strengthening, inhibition of grain growth, grain-boundary strengthening, and crack-deflection mechanisms. These results establish clear relationships between processing, phase evolution, microstructure, and mechanical behavior, demonstrating the potential of mechanochemical processing for the development of high-performance AlN-based ceramic composites intended for demanding structural and hightemperature applications.
- 22 September 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (3) , 434-447
Open AccessEFFECT OF TANTALUM AND VANADIUM CARBIDE DOPANTS ON THE STRUCTURE AND MECHANICAL PROPERTIES OF ALUMINUM NITRIDE-BASED CERAMICS
This work investigates the effect of tantalum carbide and vanadium carbide additions on the phase composition, microstructure, and mechanical properties of AlN-based ceramic composites synthesized by mechanochemical solid-state processing followed by thermal treatment. The molar fraction of the carbide additives was varied within the range of x = 0.01-0.10. Scanning electron microscopy combined with energy-dispersive X-ray spectroscopy revealed a homogeneous distribution of the reinforcing phases after mechanochemical activation. X-ray diffraction analysis showed that TaC remained chemically stable during processing, leading to the formation of a two-phase AlN-TaC composite with reduced lattice distortions of the AlN matrix. In contrast, VC underwent partial oxidation during heat treatment, resulting in the formation of secondary V 2 O 5 and a different phase evolution. Mechanochemical processing produced a more homogeneous powder morphology and suppressed the formation of large carbide agglomerates, providing favorable conditions for subsequent microstructural development. Mechanical testing demonstrated that a pronounced improvement in hardness and flexural strength occurred at dopant contents above x = 0.03, with the greatest strengthening effect observed for the TaC-containing composites owing to the retention of a stable, uniformly dispersed high-hardness carbide phase. The enhanced mechanical performance is attributed to the combined effects of dispersion strengthening, inhibition of grain growth, grain-boundary strengthening, and crack-deflection mechanisms. These results establish clear relationships between processing, phase evolution, microstructure, and mechanical behavior, demonstrating the potential of mechanochemical processing for the development of high-performance AlN-based ceramic composites intended for demanding structural and hightemperature applications.
- Open Access
- 29 April 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (5) , 239
Study of Microwave Characteristics and Compressive Strength of Mg0.5Zn0.5Fe2O4/Polystyrene/Activated Carbon Composites with Core-Shell Structure
Due to the widespread use of microwave electromagnetic radiation, this study examines the microwave electromagnetic properties and compressive strength of composites made from inexpensive components such as Mg0.5Zn0.5Fe2O4, polystyrene, and activated carbon. Experimental samples were fabricated using thermopressing. The formation of the dielectric core/shell structure for Mg-Zn/polystyrene composites (1:1) and composites with activated carbon additives at weight concentrations of 3, 6.6, and 9.0% was determined using SEM image analysis. Microwave properties were investigated by analyzing the frequency dependences of complex permittivity and magnetic permeability in the frequency range of 100 MHz–5 GHz. As shown by the simulation and experimental measurements of scattering parameters obtained, the compost shows improved microwave absorption properties in the frequency range of 1–5 GHz. Reflection loss spectra showed peaks with values of −17.8 and −18 dB in the frequency range of 2.5–5 GHz for samples with 4.8 wt. % and 6.6 wt. % carbon loading, respectively. The absorption bandwidths of −10 dB in the range of 1.7–2.13 GHz were observed in the best samples. Studies have shown that samples containing 9.0 wt. % of carbon material with thicknesses of 6–10 mm can be considered as an electromagnetic shielding material in the microwave range 1–5 GHz. It was shown that, despite a decrease in porosity from 15.59 to 7.17%, with an increase in the concentration of carbon material in the composites, the compressive strength also decreases from 62.05 to 36.45 MPa. The developed composites are potentially suitable as microwave absorbers for civil applications.
- 29 April 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (5) , 239
Open AccessStudy of Microwave Characteristics and Compressive Strength of Mg0.5Zn0.5Fe2O4/Polystyrene/Activated Carbon Composites with Core-Shell Structure
Due to the widespread use of microwave electromagnetic radiation, this study examines the microwave electromagnetic properties and compressive strength of composites made from inexpensive components such as Mg0.5Zn0.5Fe2O4, polystyrene, and activated carbon. Experimental samples were fabricated using thermopressing. The formation of the dielectric core/shell structure for Mg-Zn/polystyrene composites (1:1) and composites with activated carbon additives at weight concentrations of 3, 6.6, and 9.0% was determined using SEM image analysis. Microwave properties were investigated by analyzing the frequency dependences of complex permittivity and magnetic permeability in the frequency range of 100 MHz–5 GHz. As shown by the simulation and experimental measurements of scattering parameters obtained, the compost shows improved microwave absorption properties in the frequency range of 1–5 GHz. Reflection loss spectra showed peaks with values of −17.8 and −18 dB in the frequency range of 2.5–5 GHz for samples with 4.8 wt. % and 6.6 wt. % carbon loading, respectively. The absorption bandwidths of −10 dB in the range of 1.7–2.13 GHz were observed in the best samples. Studies have shown that samples containing 9.0 wt. % of carbon material with thicknesses of 6–10 mm can be considered as an electromagnetic shielding material in the microwave range 1–5 GHz. It was shown that, despite a decrease in porosity from 15.59 to 7.17%, with an increase in the concentration of carbon material in the composites, the compressive strength also decreases from 62.05 to 36.45 MPa. The developed composites are potentially suitable as microwave absorbers for civil applications.
- 30 March 2026
- Published by L. N. Gumilyov Eurasian National University in BULLETIN of the L.N. Gumilyov Eurasian National University. Physics. Astronomy Series
- Vol. 154 (1)
Изучение влияния вариации фазового состава в (1-x)Fe3O4 – xZnO нанокомпозитах на сдерживание механизмов коррозионного воздействия
В работе приведены результаты исследований влияния изменений фазового состава (1-x)Fe3O4 – xZnO нанокомпозитов на устойчивость к процессам коррозионного воздействия, возникающих контакт наночастиц с модельными буферными фосфатными растворами, имитирующими физиологическую среду организма. Сравнительный анализ результатов при 25 °С и 45 °С позволяет сделать вывод о том, что температура является определяющим фактором, контролирующим степень структурных изменений шпинельной фазы в жидкой среде. При комнатной температуре нанокомпозиты демонстрируют высокую кристаллохимическую стабильность, тогда как при 45 °С наблюдается постепенная эволюция катионного распределения, приводящая к увеличению степени инверсии и росту катионного беспорядка в структуре шпинели ZnFe2O4. В ходе проведенных исследований было установлено, что рост содержания аморфной фазы коррелирует с зафиксированным увеличением степени инверсии шпинельной фазы и ростом катионного беспорядка, что указывает на единый механизм деградации, включающий катионную миграцию, дефектообразование и частичную аморфизацию структуры. При этом даже в наиболее жёстких условиях деградации (45 °С, 7 суток) суммарная доля аморфных включений остаётся ограниченной, что подтверждает удовлетворительную структурную устойчивость исследуемых нанокомпозитов.
- 30 March 2026
- Published by L. N. Gumilyov Eurasian National University in BULLETIN of the L.N. Gumilyov Eurasian National University. Physics. Astronomy Series
- Vol. 154 (1)
Изучение влияния вариации фазового состава в (1-x)Fe3O4 – xZnO нанокомпозитах на сдерживание механизмов коррозионного воздействия
В работе приведены результаты исследований влияния изменений фазового состава (1-x)Fe3O4 – xZnO нанокомпозитов на устойчивость к процессам коррозионного воздействия, возникающих контакт наночастиц с модельными буферными фосфатными растворами, имитирующими физиологическую среду организма. Сравнительный анализ результатов при 25 °С и 45 °С позволяет сделать вывод о том, что температура является определяющим фактором, контролирующим степень структурных изменений шпинельной фазы в жидкой среде. При комнатной температуре нанокомпозиты демонстрируют высокую кристаллохимическую стабильность, тогда как при 45 °С наблюдается постепенная эволюция катионного распределения, приводящая к увеличению степени инверсии и росту катионного беспорядка в структуре шпинели ZnFe2O4. В ходе проведенных исследований было установлено, что рост содержания аморфной фазы коррелирует с зафиксированным увеличением степени инверсии шпинельной фазы и ростом катионного беспорядка, что указывает на единый механизм деградации, включающий катионную миграцию, дефектообразование и частичную аморфизацию структуры. При этом даже в наиболее жёстких условиях деградации (45 °С, 7 суток) суммарная доля аморфных включений остаётся ограниченной, что подтверждает удовлетворительную структурную устойчивость исследуемых нанокомпозитов.
- Open Access
- 29 December 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 22 (4 (54))
INVESTIGATION OF OPTICAL AND ELECTRICAL PROPERTIES OF TITANIUM OXYNITRIDE FILMS
In this work, titanium oxynitride films were obtained on the surface of glass and silicon substrates by magnetron sputtering in a mixture of argon-oxygen-nitrogen gases. The thickness of the obtained films, their deposition rate, and surface morphology were estimated depending on the type of substrate. The optical and electrical properties of films produced on the glass surface have been studied. A comparison of optical data with literature data showed the formation of amorphous films with a composition close to the stoichiometric composition of TiO1.27N0.49. The results showed that the obtained properties correspond to the literature data, which opens up new prospects for the use of the obtained titanium oxynitride films as an active element of memristors, and in other important areas of modern materials science.
- 29 December 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 22 (4 (54))
Open AccessINVESTIGATION OF OPTICAL AND ELECTRICAL PROPERTIES OF TITANIUM OXYNITRIDE FILMS
In this work, titanium oxynitride films were obtained on the surface of glass and silicon substrates by magnetron sputtering in a mixture of argon-oxygen-nitrogen gases. The thickness of the obtained films, their deposition rate, and surface morphology were estimated depending on the type of substrate. The optical and electrical properties of films produced on the glass surface have been studied. A comparison of optical data with literature data showed the formation of amorphous films with a composition close to the stoichiometric composition of TiO1.27N0.49. The results showed that the obtained properties correspond to the literature data, which opens up new prospects for the use of the obtained titanium oxynitride films as an active element of memristors, and in other important areas of modern materials science.
- Open Access
Sintering of Alumina-Reinforced Ceramics Using Low-Temperature Sintering Additive
Reinforced alumina ceramics are renowned for their high hardness and strength among common oxide ceramics. However, high-temperature or high-pressure treatment is necessary for maximizing values of strength and hardness. In this paper, liquid-phase-assisted pressureless sintering of alumina reinforced with zirconia was studied. Sintering of dense ceramic bodies in relatively low temperatures (up to 1100 °C) was possible with the usage of CuO-TiO2-Nb2O5-based additive, together with an intense milling process. By using the XRD method, the formation of dominant α-Al2O3 and m-ZrO2 phases with small concentrations of secondary ones in experimental samples was confirmed. SEM studies showed that uniform distribution of components in the composite was achieved in samples sintered from intensively milled powders. The significant increase in the values of Vickers hardness and biaxial flexural strength (by 2.6 times) in samples from intensively milled powders at a sintering temperature of 1050 °C was explained by reduced porosity, improved grain distribution, and the formation of the t-ZrO2 phase in the alumina-reinforced composite. The study clearly showed high potential of the proposed low-temperature sintering method for zirconia-toughened aluminum oxide, which can be used in manufacturing of advanced ceramics.
Open AccessSintering of Alumina-Reinforced Ceramics Using Low-Temperature Sintering Additive
Reinforced alumina ceramics are renowned for their high hardness and strength among common oxide ceramics. However, high-temperature or high-pressure treatment is necessary for maximizing values of strength and hardness. In this paper, liquid-phase-assisted pressureless sintering of alumina reinforced with zirconia was studied. Sintering of dense ceramic bodies in relatively low temperatures (up to 1100 °C) was possible with the usage of CuO-TiO2-Nb2O5-based additive, together with an intense milling process. By using the XRD method, the formation of dominant α-Al2O3 and m-ZrO2 phases with small concentrations of secondary ones in experimental samples was confirmed. SEM studies showed that uniform distribution of components in the composite was achieved in samples sintered from intensively milled powders. The significant increase in the values of Vickers hardness and biaxial flexural strength (by 2.6 times) in samples from intensively milled powders at a sintering temperature of 1050 °C was explained by reduced porosity, improved grain distribution, and the formation of the t-ZrO2 phase in the alumina-reinforced composite. The study clearly showed high potential of the proposed low-temperature sintering method for zirconia-toughened aluminum oxide, which can be used in manufacturing of advanced ceramics.