Anna Krapf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anna Krapf has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Christoph Gammer
Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Leoben, Austria
4 shared publications - Megan Jo Cordill
Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Leoben, Austria
4 shared publications - Benoit Merle
Institute of Materials Engineering (IFW), University of Kassel
3 shared publications - David D. Gebhart
Erich Schmid Institute of Materials Science Austrian Academy of Sciences Jahnstraße 12 8700 Leoben Austria
3 shared publications - Alice Lassnig
Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Jahnstrasse 12, 8700 Leoben, Austria
2 shared publications Benoit Merle
2 shared publications
Latest Publications
- 26 November 2025
- Published by Elsevier in Applied Materials Today
- Vol. 48
Bioinspired nacre-like hierarchical chitosan/hydroxyapatite coatings by electrophoretic deposition
- 26 November 2025
- Published by Elsevier in Applied Materials Today
- Vol. 48
Bioinspired nacre-like hierarchical chitosan/hydroxyapatite coatings by electrophoretic deposition
- Open Access
- 17 June 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 942
Microstructural and temperature-dependent deformation mechanisms governing the cyclic creep of freestanding, submicrometer gold thin films
- 17 June 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 942
Open AccessMicrostructural and temperature-dependent deformation mechanisms governing the cyclic creep of freestanding, submicrometer gold thin films
- 23 April 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (19)
Cyclic Failure of a Cr–Au Bilayer on Polyimide: In Situ Transmission Electron Microscopy Observations of Interfacial Dislocation Mechanisms
This work presents in situ transmission electron microscopy observations of dislocation activities and associated fatigue properties in a cross‐sectional sample of a Cr–Au bilayer on a polyimide substrate under cyclic loading. Dislocation structures in the Au layer are observed to evolve into a geometrically necessary boundary parallel to the Cr–Au interface, which significantly impedes dislocation motion and plays a crucial role in enhancing the fatigue resistance of the studied sample. While a comparison to the damage in a conventional blanket film testing geometry reveals some differences in the accumulation of plastic flow, the findings can provide insights into the underlying mechanisms governing fatigue in nanostructured multilayer materials on polymer substrates.
- 23 April 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (19)
Cyclic Failure of a Cr–Au Bilayer on Polyimide: In Situ Transmission Electron Microscopy Observations of Interfacial Dislocation Mechanisms
This work presents in situ transmission electron microscopy observations of dislocation activities and associated fatigue properties in a cross‐sectional sample of a Cr–Au bilayer on a polyimide substrate under cyclic loading. Dislocation structures in the Au layer are observed to evolve into a geometrically necessary boundary parallel to the Cr–Au interface, which significantly impedes dislocation motion and plays a crucial role in enhancing the fatigue resistance of the studied sample. While a comparison to the damage in a conventional blanket film testing geometry reveals some differences in the accumulation of plastic flow, the findings can provide insights into the underlying mechanisms governing fatigue in nanostructured multilayer materials on polymer substrates.
- Open Access
- 9 April 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (19)
Observing High‐Cycle Fatigue Damage in Freestanding Gold Thin Films with Bulge Testing and Intermittent Transmission Electron Microscopy Imaging
Bulge testing is a potent technique for measuring the mechanical properties of freestanding thin films, but in situ imaging is only possible in limited experimental configurations. This poses a serious limitation for unraveling nanoscale failure mechanisms, such as the deformation mechanisms induced by cyclic loading in freestanding gold thin films of 150 nm thickness. Herein, a new experimental workflow combining standalone bulge cyclic testing with intermittent high‐resolution imaging by transmission electron microscopy (TEM) at specific positions of interest is introduced. The observed low dislocation activity in planar areas of the thin films is consistent with the slow strain accumulation during high‐cycle fatigue testing. In contrast, notches in the films lead to localized plasticity with sustained dislocation activity, but also grain growth and subgrain formation. At a more advanced stage, cracks proceed along grain boundaries, with crack bridging seemingly slowing down their propagation. The presented setup can be used with a number of TEM‐based characterization techniques and has the potential to reveal cyclic deformation mechanisms in several thin‐film systems.
- 9 April 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (19)
Open AccessObserving High‐Cycle Fatigue Damage in Freestanding Gold Thin Films with Bulge Testing and Intermittent Transmission Electron Microscopy Imaging
Bulge testing is a potent technique for measuring the mechanical properties of freestanding thin films, but in situ imaging is only possible in limited experimental configurations. This poses a serious limitation for unraveling nanoscale failure mechanisms, such as the deformation mechanisms induced by cyclic loading in freestanding gold thin films of 150 nm thickness. Herein, a new experimental workflow combining standalone bulge cyclic testing with intermittent high‐resolution imaging by transmission electron microscopy (TEM) at specific positions of interest is introduced. The observed low dislocation activity in planar areas of the thin films is consistent with the slow strain accumulation during high‐cycle fatigue testing. In contrast, notches in the films lead to localized plasticity with sustained dislocation activity, but also grain growth and subgrain formation. At a more advanced stage, cracks proceed along grain boundaries, with crack bridging seemingly slowing down their propagation. The presented setup can be used with a number of TEM‐based characterization techniques and has the potential to reveal cyclic deformation mechanisms in several thin‐film systems.
- 29 September 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 887
Creep-dominated fatigue of freestanding gold thin films studied by bulge testing
- 29 September 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 887
Creep-dominated fatigue of freestanding gold thin films studied by bulge testing
- Open Access
- 27 February 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (2) , 023408
Describing mechanical damage evolution through in situ electrical resistance measurements
The fatigue properties of metallizations used as electrical conductors in flexible electronic devices have been thoroughly studied over the years. Most studies use time-intensive characterization methods to evaluate mechanical damage. For their ease of access, in situ electrical resistance measurements are often performed along with other characterization methods. However, the data are mostly used as an indicator of failure and a thorough analysis is usually missing. This work presents some deeper analysis methods of such datasets, using gold films on polyimide, with and without a chromium interlayer, revealing that grain growth, through-thickness cracking, and more general fatigue behavior can be determined from electrical resistance data alone. A case is made for increased utilization of such easily obtained data, reducing the time required for the evaluation of experiments.
- 27 February 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (2) , 023408
Open AccessDescribing mechanical damage evolution through in situ electrical resistance measurements
The fatigue properties of metallizations used as electrical conductors in flexible electronic devices have been thoroughly studied over the years. Most studies use time-intensive characterization methods to evaluate mechanical damage. For their ease of access, in situ electrical resistance measurements are often performed along with other characterization methods. However, the data are mostly used as an indicator of failure and a thorough analysis is usually missing. This work presents some deeper analysis methods of such datasets, using gold films on polyimide, with and without a chromium interlayer, revealing that grain growth, through-thickness cracking, and more general fatigue behavior can be determined from electrical resistance data alone. A case is made for increased utilization of such easily obtained data, reducing the time required for the evaluation of experiments.