Cornelis Bos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Cornelis Bos has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Ian Malcom Richardson
Department of Materials Science and Engineering, Delft University of Technology, 2628 CD Delft, The Netherlands
1 shared publication - Jilt Sietsma
Department of Materials Science and Engineering, Delft University of Technology, Delft, Netherlands
1 shared publication - Jonathan J. Eipe
Department of Materials Science and Engineering, Delft University of Technology, Delft, Netherlands
1 shared publication - Marcel J. M. Hermans
Delft University of Technology , Delft, Netherlands
1 shared publication - Monika Krugla
Tata Steel Europe R&D, 1951 JZ Velsen-Noord, The Netherlands
1 shared publication - Pablo Garcia-Chao
Department of Materials Science and Engineering, Delft University of Technology, Delft, Netherlands
1 shared publication
Latest Publications
- Open Access
- 27 February 2023
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (6) , 2160-2177
Nucleation Sites in the Static Recrystallization of a Hot-Deformed Ni-30 Pct Fe Austenite Model Alloy
In the present study, the nucleation of static recrystallization (SRX) in austenite after hot deformation is experimentally analyzed using a Ni-30 pct Fe model alloy. In agreement with the predictions by current models, nucleation rate exhibits a strong peak, early during SRX. Whereas such an early peak is explained by current models by the saturation of nucleation sites, this condition is far from reached, even after the peak declines. In addition, triple-junction and grain-boundary sites are shown to make a quantitatively similar contribution to nucleation. However, for a given boundary between deformed grains, nucleation predominantly starts at one of the triple junctions. Triple-junction nucleation initiates by strain-induced boundary migration of the nucleus (bulging) along one of the boundaries at the junction. Annealing twin boundaries contribute negligibly to nucleation through their grain-boundary sites. By contrast, their junctions with the boundaries of the parent grains do play a relevant role. The earlier nucleation at the triple junctions is attributed to the higher dislocation density observed around them, and the energy of the boundary consumed by the bulge. Both the maximum and average number of nuclei formed per boundary between deformed grains increase with increasing boundary length.
- 27 February 2023
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (6) , 2160-2177
Open AccessNucleation Sites in the Static Recrystallization of a Hot-Deformed Ni-30 Pct Fe Austenite Model Alloy
In the present study, the nucleation of static recrystallization (SRX) in austenite after hot deformation is experimentally analyzed using a Ni-30 pct Fe model alloy. In agreement with the predictions by current models, nucleation rate exhibits a strong peak, early during SRX. Whereas such an early peak is explained by current models by the saturation of nucleation sites, this condition is far from reached, even after the peak declines. In addition, triple-junction and grain-boundary sites are shown to make a quantitatively similar contribution to nucleation. However, for a given boundary between deformed grains, nucleation predominantly starts at one of the triple junctions. Triple-junction nucleation initiates by strain-induced boundary migration of the nucleus (bulging) along one of the boundaries at the junction. Annealing twin boundaries contribute negligibly to nucleation through their grain-boundary sites. By contrast, their junctions with the boundaries of the parent grains do play a relevant role. The earlier nucleation at the triple junctions is attributed to the higher dislocation density observed around them, and the energy of the boundary consumed by the bulge. Both the maximum and average number of nuclei formed per boundary between deformed grains increase with increasing boundary length.
- Open Access
- 21 February 2023
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 54 (3) , 1088-1098
An Improved Cellular Automata Solidification Model Considering Kinetic Undercooling
A cellular automata (CA) model has been developed for solidification simulation considering the kinetic undercooling at the interface. The state-of-the-art model incorporates a decentered growth algorithm to suppress the grid anisotropy and a generalized height function method to calculate the curvature accurately. To develop a CA model which is independent of the mesh size, a new diffusion term is proposed to handle the diffusion between the interface cells and liquid cells. The developed CA model is employed to simulate the single-dendritic solidification of an Al–3Cu (wt pct) alloy. The simulated tip velocities agree with the prediction of the Kurz–Giovanola–Trivedi (KGT) model. Further studies show that the developed CA model converges to an equilibrium model with increasing kinetic mobility values. Moreover, it is found that the virtual liquid cell assumption which is commonly used in existing CA models may lead to a deviation in the mass balance. The mass balance error has been resolved by redistributing solutes from neighboring liquid cells in each time step. The developed CA model could be potentially used in solidification simulations with a high undercooling, which is common in welding and additive manufacturing.
- 21 February 2023
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 54 (3) , 1088-1098
Open AccessAn Improved Cellular Automata Solidification Model Considering Kinetic Undercooling
A cellular automata (CA) model has been developed for solidification simulation considering the kinetic undercooling at the interface. The state-of-the-art model incorporates a decentered growth algorithm to suppress the grid anisotropy and a generalized height function method to calculate the curvature accurately. To develop a CA model which is independent of the mesh size, a new diffusion term is proposed to handle the diffusion between the interface cells and liquid cells. The developed CA model is employed to simulate the single-dendritic solidification of an Al–3Cu (wt pct) alloy. The simulated tip velocities agree with the prediction of the Kurz–Giovanola–Trivedi (KGT) model. Further studies show that the developed CA model converges to an equilibrium model with increasing kinetic mobility values. Moreover, it is found that the virtual liquid cell assumption which is commonly used in existing CA models may lead to a deviation in the mass balance. The mass balance error has been resolved by redistributing solutes from neighboring liquid cells in each time step. The developed CA model could be potentially used in solidification simulations with a high undercooling, which is common in welding and additive manufacturing.