Zhenhao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhenhao Li has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Lai Wang
Department of Electronic Engineering, Tsinghua University, Beijing 100084, China
7 shared publications - Bing Xiong
Department of Electronic Engineering, Tsinghua University, Beijing 100084, China
6 shared publications Hongtao Li
6 shared publicationsYanjun Han
6 shared publicationsYi Luo
Tsinghua University
6 shared publications- Changzheng Sun
Department of Electronic Engineering, Tsinghua University, Beijing 100084, China
5 shared publications
Latest Publications
- 27 February 2026
- Published by Optica Publishing Group in Photonics Research
- Vol. 14 (3) , 800
How fast can a light-emitting diode be modulated?
Beyond their traditional roles in lighting and display technologies, light-emitting diodes (LEDs) are increasingly recognized as cost-effective light sources for communication. While the modulation bandwidth of LEDs was once thought to be capped at around 100 MHz, recent advances have seen micro-scale LEDs (micro-LEDs) with bandwidths surpassing 1 GHz, driven by the demands of visible light communication applications. Emerging applications such as in-vehicle optical communication and chip-to-chip optical interconnection now require transmission speeds of 10 Gbps per channel under non-return-to-zero on-off keying (NRZ-OOK) modulation. In this context, the -3 dB bandwidth of micro-LEDs is anticipated to reach 7 GHz, significantly exceeding current capabilities. This paper systematically examines the factors that fundamentally limit the modulation bandwidth of micro-LEDs and discusses their impact as current density increases. We predict that the electrical-to-electrical (E-E) −3 dB bandwidth of quantum well (QW) micro-LEDs at room temperature will be less than 2 GHz. However, micro-LEDs featuring an InGaN quantum dot (QD) active region, due to their enhanced quantum confinement and carrier localization, have already achieved a maximum E-E −3 dB bandwidth of 3.6 GHz. Our theoretical predictions and equivalent circuit model analysis suggest that with optimizing the QD growth size, reducing the device size to less than 5 μm, and addressing the detector bandwidth limitation, this bandwidth could be measured to exceed 7 GHz. These findings pave the way for the future of high-speed, low-cost short-distance optical interconnection applications.
- 27 February 2026
- Published by Optica Publishing Group in Photonics Research
- Vol. 14 (3) , 800
How fast can a light-emitting diode be modulated?
Beyond their traditional roles in lighting and display technologies, light-emitting diodes (LEDs) are increasingly recognized as cost-effective light sources for communication. While the modulation bandwidth of LEDs was once thought to be capped at around 100 MHz, recent advances have seen micro-scale LEDs (micro-LEDs) with bandwidths surpassing 1 GHz, driven by the demands of visible light communication applications. Emerging applications such as in-vehicle optical communication and chip-to-chip optical interconnection now require transmission speeds of 10 Gbps per channel under non-return-to-zero on-off keying (NRZ-OOK) modulation. In this context, the -3 dB bandwidth of micro-LEDs is anticipated to reach 7 GHz, significantly exceeding current capabilities. This paper systematically examines the factors that fundamentally limit the modulation bandwidth of micro-LEDs and discusses their impact as current density increases. We predict that the electrical-to-electrical (E-E) −3 dB bandwidth of quantum well (QW) micro-LEDs at room temperature will be less than 2 GHz. However, micro-LEDs featuring an InGaN quantum dot (QD) active region, due to their enhanced quantum confinement and carrier localization, have already achieved a maximum E-E −3 dB bandwidth of 3.6 GHz. Our theoretical predictions and equivalent circuit model analysis suggest that with optimizing the QD growth size, reducing the device size to less than 5 μm, and addressing the detector bandwidth limitation, this bandwidth could be measured to exceed 7 GHz. These findings pave the way for the future of high-speed, low-cost short-distance optical interconnection applications.
- 30 May 2025
- Published by Optica Publishing Group in Photonics Research
- Vol. 13 (6) , 1654
170 Gbps PDM underwater visible light communication utilizing a compact 5-λ laser transmitter and a reciprocal differential receiver
The next generation of mobile communication is committed to establishing an integrated three-dimensional network that encompasses air, land, and sea. The visible light spectrum is situated within the transmission window for underwater communication, making visible light laser communication a focus of intense research. In this paper, we design and integrate a compact 5-λ transmission module based on five laser diodes with different wavelengths, utilizing a self-developed narrow-ridge GaN blue laser. With this transmitter, we have developed a polarization division multiplexing (PDM) 5-λ underwater visible light laser communication (UVLLC) system based on this transmission module. To enhance the transmission quality of the system, we designed a dual-branch ResDualNet network as a reciprocal differential receiver that incorporates common-mode noise cancellation and equalization functions for post-processing the received signals. With the combined contribution of the devices and algorithms, we achieved a total transmission rate of 170.1 Gbps, which represents a 16.1 Gbps increase compared to systems that do not utilize ResDualNet. To the best of our knowledge, this is the highest communication rate currently achievable in a UVLLC system using a single laser transmission module.
- 30 May 2025
- Published by Optica Publishing Group in Photonics Research
- Vol. 13 (6) , 1654
170 Gbps PDM underwater visible light communication utilizing a compact 5-λ laser transmitter and a reciprocal differential receiver
The next generation of mobile communication is committed to establishing an integrated three-dimensional network that encompasses air, land, and sea. The visible light spectrum is situated within the transmission window for underwater communication, making visible light laser communication a focus of intense research. In this paper, we design and integrate a compact 5-λ transmission module based on five laser diodes with different wavelengths, utilizing a self-developed narrow-ridge GaN blue laser. With this transmitter, we have developed a polarization division multiplexing (PDM) 5-λ underwater visible light laser communication (UVLLC) system based on this transmission module. To enhance the transmission quality of the system, we designed a dual-branch ResDualNet network as a reciprocal differential receiver that incorporates common-mode noise cancellation and equalization functions for post-processing the received signals. With the combined contribution of the devices and algorithms, we achieved a total transmission rate of 170.1 Gbps, which represents a 16.1 Gbps increase compared to systems that do not utilize ResDualNet. To the best of our knowledge, this is the highest communication rate currently achievable in a UVLLC system using a single laser transmission module.
- 18 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (7) , 3348-3357
21.79/17.49 Gbps Full-Duplex Visible Light Communication Enabled by Short-Cavity Blue and Green InGaN/GaN Laser Diodes
Future 6G communication includes underwater and cross-media scenarios, in which visible light laser communication (VLLC) has inherent advantages such as large capacity and transmission security. GaN-based laser diodes (LDs) are expected to play important roles in future VLLC systems, leveraging their capability in short-wavelength visible light spectrum, especially in the blue-green transmission window of water. Large bandwidth, high-speed blue/green laser devices could provide desirable channel capacity for wavelength-division full-duplex communication systems. In this paper, through theoretical analysis based on the bandwidth formula of LDs derived from the carrier rate equation, combined with numerical calculations, we design blue and green InGaN/GaN Fabry–Pérot (FP) cavity LD structures to increase bandwidth. High-bandwidth blue and green LDs for short-distance high-speed communication are fabricated by simultaneously shortening cavity length, reducing waveguide layer thickness, and increasing end-face reflectivity. The blue and green LDs achieve the −3dB E-E bandwidth of 5.4 GHz and 3.5 GHz, respectively, enabling a 21.79/17.49 Gbps full-duplex system with 21.79 Gbps downlink and 17.49 Gbps uplink using the discrete multi-tone (DMT) bit-loading modulation format. These results set a record for bandwidth and communication rate in blue and green VLLC full-duplex systems, paving the way for future high-speed applications in visible light wireless access infrastructures.
- 18 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (7) , 3348-3357
21.79/17.49 Gbps Full-Duplex Visible Light Communication Enabled by Short-Cavity Blue and Green InGaN/GaN Laser Diodes
Future 6G communication includes underwater and cross-media scenarios, in which visible light laser communication (VLLC) has inherent advantages such as large capacity and transmission security. GaN-based laser diodes (LDs) are expected to play important roles in future VLLC systems, leveraging their capability in short-wavelength visible light spectrum, especially in the blue-green transmission window of water. Large bandwidth, high-speed blue/green laser devices could provide desirable channel capacity for wavelength-division full-duplex communication systems. In this paper, through theoretical analysis based on the bandwidth formula of LDs derived from the carrier rate equation, combined with numerical calculations, we design blue and green InGaN/GaN Fabry–Pérot (FP) cavity LD structures to increase bandwidth. High-bandwidth blue and green LDs for short-distance high-speed communication are fabricated by simultaneously shortening cavity length, reducing waveguide layer thickness, and increasing end-face reflectivity. The blue and green LDs achieve the −3dB E-E bandwidth of 5.4 GHz and 3.5 GHz, respectively, enabling a 21.79/17.49 Gbps full-duplex system with 21.79 Gbps downlink and 17.49 Gbps uplink using the discrete multi-tone (DMT) bit-loading modulation format. These results set a record for bandwidth and communication rate in blue and green VLLC full-duplex systems, paving the way for future high-speed applications in visible light wireless access infrastructures.
- Open Access
- 1 October 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (10)
InGaN quantum dots for micro-LEDs
Micro-scale light-emitting diodes (micro-LEDs) have received widespread attention in recent years for applications in display and optical communication. Compared with conventional quantum well active regions, quantum dots (QDs) can increase the carrier concentration at the same current density, which is beneficial for improving the efficiency and bandwidth of LEDs at low current densities. This is exactly what micro-LEDs need for display and communication applications. In this Perspective, we give a general introduction to InGaN QDs and provide an overview of the growth of InGaN QDs by metal-organic chemical vapor deposition. We then discuss the advances in green and red micro-LEDs based on InGaN QDs for display applications. This is followed by recent progress on high-speed blue micro-LEDs, which have great potential for use in chip-to-chip optical interconnections. Finally, we address the remaining challenges for a further improvement in InGaN QD-based micro-LEDs.
- 1 October 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (10)
Open AccessInGaN quantum dots for micro-LEDs
Micro-scale light-emitting diodes (micro-LEDs) have received widespread attention in recent years for applications in display and optical communication. Compared with conventional quantum well active regions, quantum dots (QDs) can increase the carrier concentration at the same current density, which is beneficial for improving the efficiency and bandwidth of LEDs at low current densities. This is exactly what micro-LEDs need for display and communication applications. In this Perspective, we give a general introduction to InGaN QDs and provide an overview of the growth of InGaN QDs by metal-organic chemical vapor deposition. We then discuss the advances in green and red micro-LEDs based on InGaN QDs for display applications. This is followed by recent progress on high-speed blue micro-LEDs, which have great potential for use in chip-to-chip optical interconnections. Finally, we address the remaining challenges for a further improvement in InGaN QD-based micro-LEDs.
- 15 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (24) , 8760-8770
High-Speed Micro-LEDs Based on Nano-Engineered InGaN Active Region Towards Chip-to-Chip Interconnections
The application of high-speed micro-scale light-emitting diode (micro-LED) technology in short-distance data transmission breaks through the limitations of traditional electrical connections. This is particularly crucial as the demand for large-capacity and high-speed communications becomes more urgent, with a high-speed micro-LED light source being a key component. In this work, the alternating growth interruption method is used to grow a 3-layer InGaN nanostructure with smaller size and higher density. This approach increases local carrier concentration and reduces differential carrier lifetime. Based on the 3-layer improved InGaN nanostructure, a blue micro-LED is designed and fabricated, achieving the output optical power exceeding 0.5 mW while the electro-electric (E-E) −3 dB bandwidth exceeding 2.6 GHz. Utilizing this high-speed micro-LED as the light source, three non-return-to-zero on-off keying (NRZ-OOK) real-time communication systems are demonstrated: single-channel transmission via free-space and quartz optical fiber, and 4-channel transmission via plastic imaging fiber, achieving data rates of 3.07, 2.60, and 12.00 Gbps, respectively. Additionally, the 4-channel system achieves bit-power loading discrete multi-tone (DMT) transmission of 15.05 Gbps.
- 15 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (24) , 8760-8770
High-Speed Micro-LEDs Based on Nano-Engineered InGaN Active Region Towards Chip-to-Chip Interconnections
The application of high-speed micro-scale light-emitting diode (micro-LED) technology in short-distance data transmission breaks through the limitations of traditional electrical connections. This is particularly crucial as the demand for large-capacity and high-speed communications becomes more urgent, with a high-speed micro-LED light source being a key component. In this work, the alternating growth interruption method is used to grow a 3-layer InGaN nanostructure with smaller size and higher density. This approach increases local carrier concentration and reduces differential carrier lifetime. Based on the 3-layer improved InGaN nanostructure, a blue micro-LED is designed and fabricated, achieving the output optical power exceeding 0.5 mW while the electro-electric (E-E) −3 dB bandwidth exceeding 2.6 GHz. Utilizing this high-speed micro-LED as the light source, three non-return-to-zero on-off keying (NRZ-OOK) real-time communication systems are demonstrated: single-channel transmission via free-space and quartz optical fiber, and 4-channel transmission via plastic imaging fiber, achieving data rates of 3.07, 2.60, and 12.00 Gbps, respectively. Additionally, the 4-channel system achieves bit-power loading discrete multi-tone (DMT) transmission of 15.05 Gbps.
- 13 August 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (18) , 31238-31246
Color tunable inverted pyramid micro-LEDs based on nano-patterned sapphire substrates
Color-tunable micro-scale light-emitting diodes (Micro-LEDs) can achieve full-color display in a simple and low-cost way. In this paper, we demonstrate growth of three-dimensional (3D) inverted pyramid GaN on nano-patterned sapphire substrates (NPSS). By using the sputtered AlN nucleation layer, the uniformity of the inverted pyramid has been improved to a large extent. Then, Micro-LEDs are epitaxially grown based on these inverted pyramids and fabricated to 20-100 µm devices. As the current increases from 1 to 100 A/cm2, the electroluminescence (EL) wavelength exhibits a large blueshift from 660 to 470 nm, corresponding to the dominant emission changing from polar InGaN multi-quantum-well (MQW) facets to semipolar ones. This color-tunable range almost covers 97% of the sRGB color gamut. Considering the combination of display and communication in the future internet of everything (IoE) era, the modulation bandwidths of the Micro-LEDs are measured to explore the carrier recombination rates of different facets in inverted pyramids. Different modulation bandwidths in polar and semipolar InGaN MQW have been observed at the current density above 60 A/cm2, and the highest -3 dB electro-optic bandwidth of 1.28 GHz from the latter is achieved at the current density of 25 kA/cm2.
- 13 August 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (18) , 31238-31246
Color tunable inverted pyramid micro-LEDs based on nano-patterned sapphire substrates
Color-tunable micro-scale light-emitting diodes (Micro-LEDs) can achieve full-color display in a simple and low-cost way. In this paper, we demonstrate growth of three-dimensional (3D) inverted pyramid GaN on nano-patterned sapphire substrates (NPSS). By using the sputtered AlN nucleation layer, the uniformity of the inverted pyramid has been improved to a large extent. Then, Micro-LEDs are epitaxially grown based on these inverted pyramids and fabricated to 20-100 µm devices. As the current increases from 1 to 100 A/cm2, the electroluminescence (EL) wavelength exhibits a large blueshift from 660 to 470 nm, corresponding to the dominant emission changing from polar InGaN multi-quantum-well (MQW) facets to semipolar ones. This color-tunable range almost covers 97% of the sRGB color gamut. Considering the combination of display and communication in the future internet of everything (IoE) era, the modulation bandwidths of the Micro-LEDs are measured to explore the carrier recombination rates of different facets in inverted pyramids. Different modulation bandwidths in polar and semipolar InGaN MQW have been observed at the current density above 60 A/cm2, and the highest -3 dB electro-optic bandwidth of 1.28 GHz from the latter is achieved at the current density of 25 kA/cm2.
- 13 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (5) , 785-788
Bandwidth Analysis of High-Speed InGaN Micro-LEDs by an Equivalent Circuit Model
High-speed light-emitting diodes (LEDs) are ideal light sources for low-cost plastic optical fiber communication in data-centers and vehicles. Here, high-speed micro-LEDs based on InGaN quantum dot (QD) active region with different diameters are fabricated and characterized. The −3dB bandwidth around 3.6 GHz and 1.4 GHz are achieved in the blue and green micro-LEDs under current density less than 1 kA/cm2, respectively, which can work at an environmental temperature of 125 °C. An equivalent circuit model is proposed to analyze the limiting factors of the bandwidth, using which the effects of carrier recombination and RC time constant on modulation bandwidth are separated. It is found that carrier recombination rate is fast enough and the RC constant is still the main limiting factor for the blue micro-LEDs at an injection current density of more than 500 A/cm2 even when the diameter scales down to $20 \mu \text{m}$ , while the recombination rate mainly limits the bandwidth of the green micro-LEDs.
- 13 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (5) , 785-788
Bandwidth Analysis of High-Speed InGaN Micro-LEDs by an Equivalent Circuit Model
High-speed light-emitting diodes (LEDs) are ideal light sources for low-cost plastic optical fiber communication in data-centers and vehicles. Here, high-speed micro-LEDs based on InGaN quantum dot (QD) active region with different diameters are fabricated and characterized. The −3dB bandwidth around 3.6 GHz and 1.4 GHz are achieved in the blue and green micro-LEDs under current density less than 1 kA/cm2, respectively, which can work at an environmental temperature of 125 °C. An equivalent circuit model is proposed to analyze the limiting factors of the bandwidth, using which the effects of carrier recombination and RC time constant on modulation bandwidth are separated. It is found that carrier recombination rate is fast enough and the RC constant is still the main limiting factor for the blue micro-LEDs at an injection current density of more than 500 A/cm2 even when the diameter scales down to $20 \mu \text{m}$ , while the recombination rate mainly limits the bandwidth of the green micro-LEDs.