Silvano Cortesi

Indoor localization systems face a fundamental trade-off between energy efficiency and responsiveness, which is especially important for emerging use cases such as mobile robots operating in GPS-denied environments. Traditional real-time locating system (RTLS) either require continuously powered infrastructure, limiting their scalability, or are limited by their responsiveness. This work presents Eco-WakeLoc, designed to achieve centimeter-level ultra-wideband (UWB) localization while remaining energy-neutral by combining ultra-low power wake-up radios (WuRs) with solar energy harvesting. By activating anchor nodes only on demand, the proposed system eliminates constant energy consumption while achieving centimeter-level positioning accuracy. To reduce coordination overhead and improve scalability, Eco-WakeLoc employs cooperative localization where active tags initiate ranging exchanges, while passive tags opportunistically reuse these messages for time difference of arrival (TDOA) positioning. An additive-increase/multiplicative-decrease (AIMD)-based energy-aware scheduler adapts localization rates according to the harvested energy, thereby maximizing the overall performance of the sensor network while ensuring long-term energy neutrality. A comprehensive evaluation demonstrates centimeter-level accuracy with average errors in 3D space of 21.89cm for active tags using Levenberg-Marquardt trilateration, and 25.70cm for passive tags through cooperative TDOA. The measured energy consumption is only 3.22mJ per localization for active tags, 951 μJ for passive tags, and 353 μJ for anchors. Real-world deployment on a quadruped robot with nine anchors confirms the practical feasibility, achieving an average accuracy of 43cm in dynamic indoor environments. Year-long simulations starting from an empty battery, and using solar harvesting from a 10cm² cell under typical indoor lighting conditions, show that tags achieve an average of 2031 localizations per day, while retaining over 7%battery capacity after one year – demonstrating that the RTLS achieves sustained energy-neutral operation. Eco-WakeLoc demonstrates that high-accuracy indoor localization can be achieved at scale without continuous infrastructure operation, combining energy neutrality, cooperative positioning, and adaptive scheduling to enable maintenance-free deployments suitable for large-scale Internet of Things applications.

Accurate localization is essential for a wide range of applications, including asset tracking, smart agriculture, and animal monitoring. While traditional localization methods, such as Global Navigation Satellite System (GNSS), Wi-Fi, and Bluetooth Low Energy (BLE), offer varying levels of accuracy and coverage, they have drawbacks regarding power consumption, infrastructure requirements, and deployment flexibility. Ultra-Wideband (UWB) is emerging as an alternative, offering centimeter-level accuracy and energy efficiency, especially suitable for medium to large field monitoring with capabilities to work indoors and outdoors. However, existing UWB localization systems require infrastructure with mains power to supply the anchors, which impedes their scalability and ease of deployment. This underscores the need for a fully battery-powered and energy-efficient localization system. This paper presents an energy-optimized, battery-operated UWB localization system that leverages Long Range Wide Area Network (LoRaWAN) for data transmission to a server backend. By employing single-sided two-way ranging (SS-TWR) in a time-slotted localization approach, the power consumption both on the anchor and the tag is reduced, while maintaining high accuracy. With a low average power consumption of 20.44 mW per anchor and 7.19 mW per tag, the system allows fully battery-powered operation for up to 25 days, achieving average accuracy of 13.96 cm with self-localizing anchors on a 600 m2 testing ground. To validate its effectiveness and ease of installation in a challenging application scenario, ten anchors and two tags were successfully deployed in a tropical zoological biome where they could be used to track Aldabra Giant Tortoises (Aldabrachelys gigantea).

For future large scale robotic moon missions, the availability of infrastructure-less, cheap and low power real-time locating systems (RTLSs) is critical. Traditional RTLS face significant trade-offs between power consumption and localization latency, often requiring anchors to be connected to the power grid or sacrificing speed for energy efficiency. This paper proposes WakeLoc, an on-demand RTLS based on ultra-wideband (UWB), enabling both low-latency and ultra-low power consumption by leveraging UWB wake-up radios (WuRs). In WakeLoc, tags independently start a localization procedure by sending a wake-up call (WuC) to anchors, before performing the actual localization. Distributed tags equipped with WuRs listen to the WuC and use passive listening of the UWB messages to determine their own position. Experimental measurements demonstrate that the localization accuracy in a 2D setup achieves less than 12.9cm error, both for the active and the passive tag. Additional power simulations based on real-world measurements were performed in a realistic environment, showing that anchors can achieve a power consumption as low as 15.53μW while the RTLS performs one on-demand localization per minute for 5 tags, thus operate up to 5.01 years on a single coin cell battery (690mWh).

Asset tracking solutions have proven their significance in industrial contexts, as evidenced by their successful commercialization (e.g., Hilti On!Track). However, a seamless solution for matching assets with their users, such as operators of construction power tools, is still missing. By enabling asset-user matching, organizations gain valuable insights that can be used to optimize user health and safety, asset utilization, and maintenance. This article introduces a novel approach to address this gap by leveraging existing Bluetooth low energy (BLE)-enabled low-power Internet of Things (IoT) devices. The proposed framework comprises the following components: 1) a wearable device; 2) an IoT device attached to or embedded in the assets; 3) an algorithm to estimate the distance between assets and operators by exploiting simple received signal strength indicator (RSSI) measurements via an extended Kalman filter (EKF); and 4) a cloud-based algorithm that collects all estimated distances to derive the correct asset-operator matching. The effectiveness of the proposed system has been validated through indoor and outdoor experiments in a construction setting for identifying the operator of a power tool. A physical prototype was developed to evaluate the algorithms in a realistic setup. The results demonstrated a median accuracy of 0.49m in estimating the distance between assets and users, and up to 98.6% in correctly matching users with their assets.

Step-counting has been widely implemented in wrist-worn devices and is accepted by end users as a quantitative indicator of everyday exercise. However, existing counting approach (mostly on wrist-worn setup) lacks robustness and thus introduces inaccuracy issues in certain scenarios like brief intermittent walking bouts and random arm motions or static arm status while walking (no clear correlation of motion pattern between arm and leg). This paper proposes a low-power step-counting solution utilizing the body area electric field acquired by a novel electrostatic sensing unit, consuming only 87.3 µW of power, hoping to strengthen the robustness of current dominant solution. We designed two wearable devices for on-the-wrist and in-the-ear deployment and collected body-area electric field-derived motion signals from ten volunteers. Four walking scenarios are considered: in the parking lot/shopping center with/without pushing the shopping trolley. The step-counting accuracy from the prototypes shows better accuracy than the commercial wrist-worn devices (e.g.,96% of the wrist- and ear-worn prototype vs. 66% of the Fitbit when walking in the shopping center while pushing a shopping trolley). We finally discussed the potential and limitations of sensing body-area electric fields for wrist-worn and ear-worn step-counting and beyond.

Step-counting has been widely implemented in wrist-worn devices and is accepted by end users as a quantitative indicator of everyday exercise. However, existing counting approach (mostly on wrist-worn setup) lacks robustness and thus introduces inaccuracy issues in certain scenarios like brief intermittent walking bouts and random arm motions or static arm status while walking (no clear correlation of motion pattern between arm and leg). This paper proposes a low-power step-counting solution utilizing the body area electric field acquired by a novel electrostatic sensing unit, consuming only 87.3 $μ$W of power, hoping to strengthen the robustness of current dominant solution. We designed two wearable devices for on-the-wrist and in-the-ear deployment and collected body-area electric field-derived motion signals from ten volunteers. Four walking scenarios are considered: in the parking lot/shopping center with/without pushing the shopping trolley. The step-counting accuracy from the prototypes shows better accuracy than the commercial wrist-worn devices (e.g.,96% of the wrist- and ear-worn prototype vs. 66% of the Fitbit when walking in the shopping center while pushing a shopping trolley). We finally discussed the potential and limitations of sensing body-area electric fields for wrist-worn and ear-worn step-counting and beyond.

In the ever-growing Internet of Things (IoT) landscape, smart power management algorithms combined with energy harvesting solutions are crucial to obtain self-sustainability. This paper presents an energy-aware adaptive sampling rate algorithm designed for embedded deployment in resource-constrained, battery-powered IoT devices. The algorithm, based on a finite state machine (FSM) and inspired by Transmission Control Protocol (TCP) Reno's additive increase and multiplicative decrease, maximizes sensor sampling rates, ensuring power self-sustainability without risking battery depletion. Moreover, we characterized our solar cell with data acquired over 48 days and used the model created to obtain energy data from an open-source world-wide dataset. To validate our approach, we introduce the EcoTrack device, a versatile device with global navigation satellite system (GNSS) capabilities and Long-Term Evolution Machine Type Communication (LTE-M) connectivity, supporting MQTT protocol for cloud data relay. This multi-purpose device can be used, for instance, as a health and safety wearable, remote hazard monitoring system, or as a global asset tracker. The results, validated on data from three different European cities, show that the proposed algorithm enables self-sustainability while maximizing sampled locations per day. In experiments conducted with a 3000 mAh battery capacity, the algorithm consistently maintained a minimum of 24 localizations per day and achieved peaks of up to 3000.

This paper introduces an effective solution for retrofitting construction power tools with low-power IoT to enable accurate activity classification. We address the challenge of distinguishing between when a power tool is being moved and when it is actually being used. To achieve classification accuracy and power consumption preservation a newly released algorithm called MiniRocket was employed. Known for its accuracy, scalability, and fast training for time-series classification, in this paper, it is proposed as a TinyML algorithm for inference on resource-constrained IoT devices. The paper demonstrates the portability and performance of MiniRocket on a resource-constrained, ultra-low power sensor node for floating-point and fixed-point arithmetic, matching up to 1% of the floating-point accuracy. The hyperparameters of the algorithm have been optimized for the task at hand to find a Pareto point that balances memory usage, accuracy and energy consumption. For the classification problem, we rely on an accelerometer as the sole sensor source, and BLE for data transmission. Extensive real-world construction data, using 16 different power tools, were collected, labeled, and used to validate the algorithm's performance directly embedded in the IoT device. Experimental results demonstrate that the proposed solution achieves an accuracy of 96.9% in distinguishing between real usage status and other motion statuses while consuming only 7kB of flash and 3kB of RAM. The final application exhibits an average current consumption of less than 15μW for the whole system, resulting in battery life performance ranging from 3 to 9 years depending on the battery capacity (250-500mAh) and the number of power tool usage hours (100-1500h).

Accurate and low-power indoor localization is becoming more and more of a necessity to empower novel consumer and industrial applications. In this field, the most promising technology is based on Ultra-Wideband (UWB) modulation; however, current UWB positioning systems do not reach centimeter accuracy in general deployments due to multi-path and non-isotropic antennas, still necessitating several fixed anchors to estimate an object’s position in space. This paper presents an in-depth study and assessment of Angle of Arrival (AoA) UWB measurements using a compact, low-power solution integrating a novel commercial module with Phase Difference of Arrival (PDoA) estimation as integrated feature. Results demonstrate the possibility of reaching centimeter distance precision and 2.4° average angular accuracy in many operative conditions, e.g., in a 90° range around the center. Moreover, integrating the channel impulse response, the phase differential of arrival, and the point-to-point distance, an error correction model is discussed to compensate for reflections, multi-paths, and front-back ambiguity.

IPS is a crucial technology that enables medical staff and hospital management to accurately locate and track persons or assets inside medical buildings. Among other technologies, readily available BLE can be exploited to achieve an energy-efficient and low-cost solution. This work presents the design, implementation and comparison of a RSSI-based and a MCPD-based indoor localization system. The implementation is based on a lightweight wkNN algorithm that processes RSSI and MCPD distance data from connection-less BLE Beacons. The designed hardware and firmware are implemented around the state-of-the-art SoC for BLE, the nRF5340 from Nordic Semiconductor. Experimental evaluation with real-time data processing has been evaluated and presented in a 7.3 m × 8.9 m room with furniture and six beacon nodes. The experimental results on randomly chosen validation points within the room show an average error of only 0.50 m for the MCPD approach, whereas the RSSI approach achieved an error of 1.39 m.