Matthias Fischer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Matthias Fischer has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Heike Beismann
Institute for Biomimetics, Westphalian University of Applied Sciences, 46397 Bocholt, Germany
2 shared publications - Lars Böckenholt
Westfälische Hochschule, Münsterstraße 265, 46397 Bocholt, Germany
1 shared publication - Leon S. Lorenz
Westfälische Hochschule, Münsterstraße 265, 46397 Bocholt, Germany
1 shared publication - Max David Mylo
Cluster of Excellence livMatS @ FIT—Freiburg Center for Interactive Materials and Bioinspired Technologies, University of Freiburg, Freiburg im Breisgau, Germanyhttps://ror.org/0245cg223https://www.isni.org/isni
1 shared publication Michael Bennemann
Westfalian Institute for Biomimetics, Westfalian University of Applied Sciences, Münsterstraße 265, 46397 Bocholt, Germany
1 shared publication- Moses-Gereon Wullweber
Westfalian University of Applied Sciences, Münsterstrasse 265, 46397 Bocholt, Germany
1 shared publication
Latest Publications
- Open Access
- 29 March 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (4) , 207
Reducing Automotive Cooling System Complexity through an Adaptive Biomimetic Air Control Valve
Future automotive mobility is predominantly electric. Compared to existing systems, the requirements of subsystems change. Air flow for cooling components is needed predominantly when the car is in rest (i.e., charging) or at slow speeds. So far, actively driven fans consuming power and generating noise are used in this case. Here we propose a passive adaptive system allowing for convection-driven cooling. The developed system is a highly adaptive flat valve derived from the bordered pit. It was developed through an iterative design process including simulations, both structural and thermodynamic. In hardwoods and conifers, bordered pits enable the challenging transport of vertical fluids by locally limiting damage. Depending on the structure, these can close at sudden pressure changes and take the function of valves. The result of the biomimetic abstraction process is a system-integrative, low-profile valve that is cheap to produce, long-lasting, lightweight, maintenance-free, and noise-free. It allows for the passive switching of air flow generation at the heat exchanger of the cooling between natural convection or an active airstream without the need for complex sensing and control systems. The geometric and material design factors allow for the simple tuning of the valve to the desired switching conditions during the design process.
- 29 March 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (4) , 207
Open AccessReducing Automotive Cooling System Complexity through an Adaptive Biomimetic Air Control Valve
Future automotive mobility is predominantly electric. Compared to existing systems, the requirements of subsystems change. Air flow for cooling components is needed predominantly when the car is in rest (i.e., charging) or at slow speeds. So far, actively driven fans consuming power and generating noise are used in this case. Here we propose a passive adaptive system allowing for convection-driven cooling. The developed system is a highly adaptive flat valve derived from the bordered pit. It was developed through an iterative design process including simulations, both structural and thermodynamic. In hardwoods and conifers, bordered pits enable the challenging transport of vertical fluids by locally limiting damage. Depending on the structure, these can close at sudden pressure changes and take the function of valves. The result of the biomimetic abstraction process is a system-integrative, low-profile valve that is cheap to produce, long-lasting, lightweight, maintenance-free, and noise-free. It allows for the passive switching of air flow generation at the heat exchanger of the cooling between natural convection or an active airstream without the need for complex sensing and control systems. The geometric and material design factors allow for the simple tuning of the valve to the desired switching conditions during the design process.
- Open Access
- 21 March 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (3) , 191
Stereo Camera Setup for 360° Digital Image Correlation to Reveal Smart Structures of Hakea Fruits
About forty years after its first application, digital image correlation (DIC) has become an established method for measuring surface displacements and deformations of objects under stress. To date, DIC has been used in a variety of in vitro and in vivo studies to biomechanically characterise biological samples in order to reveal biomimetic principles. However, when surfaces of samples strongly deform or twist, they cannot be thoroughly traced. To overcome this challenge, different DIC setups have been developed to provide additional sensor perspectives and, thus, capture larger parts of an object’s surface. Herein, we discuss current solutions for this multi-perspective DIC, and we present our own approach to a 360° DIC system based on a single stereo-camera setup. Using this setup, we are able to characterise the desiccation-driven opening mechanism of two woody Hakea fruits over their entire surfaces. Both the breaking mechanism and the actuation of the two valves in predominantly dead plant material are models for smart materials. Based on these results, an evaluation of the setup for 360° DIC regarding its use in deducing biomimetic principles is given. Furthermore, we propose a way to improve and apply the method for future measurements.
- 21 March 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (3) , 191
Open AccessStereo Camera Setup for 360° Digital Image Correlation to Reveal Smart Structures of Hakea Fruits
About forty years after its first application, digital image correlation (DIC) has become an established method for measuring surface displacements and deformations of objects under stress. To date, DIC has been used in a variety of in vitro and in vivo studies to biomechanically characterise biological samples in order to reveal biomimetic principles. However, when surfaces of samples strongly deform or twist, they cannot be thoroughly traced. To overcome this challenge, different DIC setups have been developed to provide additional sensor perspectives and, thus, capture larger parts of an object’s surface. Herein, we discuss current solutions for this multi-perspective DIC, and we present our own approach to a 360° DIC system based on a single stereo-camera setup. Using this setup, we are able to characterise the desiccation-driven opening mechanism of two woody Hakea fruits over their entire surfaces. Both the breaking mechanism and the actuation of the two valves in predominantly dead plant material are models for smart materials. Based on these results, an evaluation of the setup for 360° DIC regarding its use in deducing biomimetic principles is given. Furthermore, we propose a way to improve and apply the method for future measurements.
- 15 March 2023
- Published by Springer Nature
- p. 31-53
Review of the State of the Art Using µCT to Elucidate Complex Vascular Systems of Plants
- 15 March 2023
- Published by Springer Nature
- p. 31-53
Review of the State of the Art Using µCT to Elucidate Complex Vascular Systems of Plants