QFQiang Fang

Qiang Fang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qiang Fang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Analysis of Shale Cuttings Migration in Horizontal Wells

    by Qiang Fang, Mingyu Ma, Dong Xiao, Ming Wang, Xiaoqi Ning

    The extraction of shale gas via horizontal drilling presents considerable challenges, primarily due to the accumulation of cuttings within the annular space, resulting in increased friction, torque, and potential drilling complications. To address this issue, the study proposes an experimental setup aimed at simulating cuttings transport under various operational conditions, with a particular emphasis on gas wells. The methodology encompasses the modulation of the drilling fluid flow rate and the drill’s rotational speed to examine the transport velocity of cuttings. Furthermore, the study analyzes the impact of annular eccentricity on return volume, transport time, and cuttings bed height. Critical initiation velocities for cuttings across different motion modes were also determined, and theoretical calculations were compared with empirical data. The findings indicate that an increased flow rate of drilling fluid and higher rotation speed substantially improve the transport of cuttings, thereby minimizing bed formation, whereas increased eccentricity hinders this process. The results revealed that the theoretical model showed a greater overestimation of the start-up velocity for spherical particles, with average errors ranging from 15.50% to 17.56%. In contrast, the model exhibited better accuracy for non-spherical (flaky) particles, with errors between 8.63% and 9.61%. Under non-rotating conditions, the average error of the model was approximately 8.32%, while the introduction of drill tool rotation increased the average error to 11.94%. These results have the potential to optimize operational parameters in shale gas well drilling and may contribute to the development of specialized borehole purification tools.


  • Open Access

    A Predictive Model for Wellbore Temperature in High-Sulfur Gas Wells Incorporating Sulfur Deposition

    by Qiang Fang, Jinghong He, Yang Wang, Hong Pan, Hongming Ren, Hao Liu

    HSG (high-sulfur gas) reservoirs are prevalent globally, yet their exploitation is hindered by elevated levels of hydrogen sulfide. A decrease in temperature and pressure may result in the formation of sulfur deposits, thereby exerting a notable influence on gas production. Test instruments are susceptible to significant corrosion due to the presence of hydrogen sulfide, resulting in challenges in obtaining bottom hole temperature and pressure test data. Consequently, a WTD (wellbore temperature distribution) model incorporating sulfur precipitation was developed based on PPP (physical property parameter), heat transfer, and GSTP (gas–solid two-phase) flow models. The comparison of a 2.53% temperature error and a 4.80% pressure error with actual field test data indicates that the established model exhibits high accuracy. An analysis is conducted on the impact of various factors, such as production, sulfur layer thickness, reservoir temperature, and reservoir pressure, on the distribution of the wellbore temperature field and pressure field. Increased gas production leads to higher wellhead temperatures. The presence of sulfur deposits reduces the flow area and wellhead pressure. A 40% concentration of hydrogen sulfide results in a 2 MPa pressure drop compared to a 20% concentration. Decreased reservoir pressure and temperature facilitate the formation of sulfur deposits at the wellhead.


  • Open Access

    Numerical Study of the Erosion Distribution of Sulfur-Containing Particulate Gas in 90-Degree Gathering Elbow

    by Runhua Zhu, Hongming Ren, Qiang Fang, Yang Ren, Dong Jiang, Yongliang Liu, Shudong Liu, Chengyong Li, Danni Tang

    The phenomenon of pipeline erosion dominated by sulfur particles has become a key research target for sulfur-containing gas-gathering pipelines. Gas-solid two-phase flow of sulfur-containing gases is simulated with a coupled CFD-DPM model in this paper. The Realizable k-ε turbulence model was used to determine the changes in the complex flow field and the Euler-Lagrange method was used to describe the specific trajectory of sulfur particles in the complex flow field. The main erosion trace distribution and the effect of secondary flow effects at the elbow were analyzed and the erosion distribution pattern was investigated for different curvature ratios, particle sizes, and pipe diameters. The results show that the formation of erosion along the tip of the V-shaped erosion trace on the outlet sidewall of the elbow may be related to secondary flow effects. The increase of the curvature ratio RD reduces the erosion intensity of the maximum erosion area, but subsequent increase will result in new secondary erosion trace near the outlet of the elbow and reach the maximum when RD = 8. Variations in particle size will have a significant effect on the extent of the erosion distribution, causing the main erosion distribution of the elbow to vary between 48.2° and 84.2°, while variations in pipeline diameter will have a lesser effect. The Stokes number can also be reduced by controlling the variation in particle size and pipe diameter to alter the force profile on the particles and reduce the erosion effect.