S. A. Kostin
Research Subjects
S. A. Kostin has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Sergei Pavlovich Galkin
University of Science and Technology MISIS, Moscow, Russian Federation
2 shared publications - Tatiana Yu. Kin
University of Science and Technology MISIS, Moscow, Russian Federation
2 shared publications - Yury V. Gamin
National University of Science and Technology MISiS, Moscow, Russian Federation
2 shared publications - Andrey Korotitskiy
National University of Science and Technology “MISIS
1 shared publication - E. O. Tikhomirov
National University of Science and Technology MISiS, Moscow, Russia
1 shared publication
Latest Publications
- 30 September 2023
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 9,p. 47-53
Experimental testing of radial-shear rolling to obtain a deformed alloy of the Co – Cr – Mo system
An experimental testing of the technology for obtaining a deformed Co-28Cr-6Mo alloy using radial shear rolling is presented. Mechanical peeled and homogenized ingots of vacuum induction melting with a diameter of 57 mm were subjected to radial shear rolling in 4-5 passes to bars with a diameter of 18 and 29 mm at a temperature of 1200 °C with quenching of the final profile in water or cooling in air. A study of the microstructure, mechanical properties in the cast and deformed state was carried out. The requirements of GOST ISO 5832-12-2009 in terms of normalized indicators - tensile strength, yield strength and relative elongation are fully satisfied. At the same time, there is an increase in relative elongation by 1.4-1.6 times compared with the initial cast state and an excess of regulatory requirements by 3.0-3.3 times. The experimental technology has been implemented at NUST MISIS radial shear rolling mills and has the prospect of industrial scaling. The very significant advantages of the proposed technology include a small total elongation ratio (μ = 3.86), which ensures that the requirements of GOST on mechanical properties for the deformed Co-Cr-Mo alloy are met.The study was supported by the Russian Science Foundation grant No. 23-19-00477, https://rscf.ru/project/23-19-00477/.
- 30 September 2023
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 9,p. 47-53
Experimental testing of radial-shear rolling to obtain a deformed alloy of the Co – Cr – Mo system
An experimental testing of the technology for obtaining a deformed Co-28Cr-6Mo alloy using radial shear rolling is presented. Mechanical peeled and homogenized ingots of vacuum induction melting with a diameter of 57 mm were subjected to radial shear rolling in 4-5 passes to bars with a diameter of 18 and 29 mm at a temperature of 1200 °C with quenching of the final profile in water or cooling in air. A study of the microstructure, mechanical properties in the cast and deformed state was carried out. The requirements of GOST ISO 5832-12-2009 in terms of normalized indicators - tensile strength, yield strength and relative elongation are fully satisfied. At the same time, there is an increase in relative elongation by 1.4-1.6 times compared with the initial cast state and an excess of regulatory requirements by 3.0-3.3 times. The experimental technology has been implemented at NUST MISIS radial shear rolling mills and has the prospect of industrial scaling. The very significant advantages of the proposed technology include a small total elongation ratio (μ = 3.86), which ensures that the requirements of GOST on mechanical properties for the deformed Co-Cr-Mo alloy are met.The study was supported by the Russian Science Foundation grant No. 23-19-00477, https://rscf.ru/project/23-19-00477/.
- 1 November 2022
- Published by Allerton Press in Steel in Translation
- Vol. 52 (11) , 1027-1036
Development of Temperature-Rate Modes of Hot Deformation of the Co–28Cr–6Mo Alloy Based on Processing Maps
The Co–28Cr–6Mo medical alloy after homogenization is tested in uniaxial compression at temperatures of 1000, 1100, and 1200°C and strain
- 1 November 2022
- Published by Allerton Press in Steel in Translation
- Vol. 52 (11) , 1027-1036
Development of Temperature-Rate Modes of Hot Deformation of the Co–28Cr–6Mo Alloy Based on Processing Maps
The Co–28Cr–6Mo medical alloy after homogenization is tested in uniaxial compression at temperatures of 1000, 1100, and 1200°C and strain