K. K. Ilavenil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
K. K. Ilavenil has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
V. Senthilkumar
3 shared publications- Vagheesan Senthilkumar
Department of Mechanical Engineering, SRM TRP Engineering College, Trichy, India
3 shared publications A. Kasthuri
Department of Chemistry, Nehru Memorial College (Autonomous) / Affiliated to Bharathidasan University, Puthanampatti, Tiruchirappalli, India
2 shared publications- A. Kasthuri
Department of Chemistry, Nehru Memorial College (Autonomous) /Affiliated to Bharathidasan University, Puthanampatti, Tiruchirappalli, Tamilnadu, India
2 shared publications - Anbazhagan Nagadeepan
Department of Mechanical Engineering, SRM TRP Engineering College, Trichy 621105, Tamilnadu, India
2 shared publications - P. Pandian
Department of Chemistry, Thanthai Periyar Government Arts and Science College (Autonomous) / Affiliated to Bharathidasan University, Tiruchirappalli, Tamilnadu, India
2 shared publications
Latest Publications
- Open Access
- 24 July 2026
- Published by MDPI AG in Automation
- Vol. 7 (4) , 115
Sustainable and Intelligent Automation Framework for Aerospace Alloys Using Multi-Agent Deep Reinforcement Learning
Advanced aerospace alloys such as titanium alloy (Ti-6Al-4V) are widely employed in critical applications owing to their excellent strength-to-weight ratio and corrosion resistance. However, machining these alloys remains challenging due to significant tool wear, poor material removal rates, and surface integrity concerns. This research offers a sustainable and intelligent machining framework for a 3 mm thick Ti-6Al-4V alloy, utilizing coated wire electrical discharge machining (WEDM) linked with Multi-Agent Deep Reinforcement Learning (MADRL). A Box–Behnken experimental design was adopted to gather baseline data for pulse-on time, pulse-off time, servo voltage, and peak current. The MADRL architecture combines cooperative agents to improve MRR, surface roughness, and kerf width concurrently. Beyond performance increase, the sustainability parameters of energy consumption, dielectric fluid use, and wire consumption were also studied. The proposed MADRL significantly improved the material removal rate (MRR) from 1.00 to 1.28 mm3/min and reduced the average surface roughness (Ra) from 1.95 to 1.66 µm, the kerf width from 0.27 to 0.24 mm, and the energy consumption from 122 to 107 J. The results show the potential of the proposed framework for adaptive, sustainable, and high-performance aerospace manufacturing.
- 24 July 2026
- Published by MDPI AG in Automation
- Vol. 7 (4) , 115
Open AccessSustainable and Intelligent Automation Framework for Aerospace Alloys Using Multi-Agent Deep Reinforcement Learning
Advanced aerospace alloys such as titanium alloy (Ti-6Al-4V) are widely employed in critical applications owing to their excellent strength-to-weight ratio and corrosion resistance. However, machining these alloys remains challenging due to significant tool wear, poor material removal rates, and surface integrity concerns. This research offers a sustainable and intelligent machining framework for a 3 mm thick Ti-6Al-4V alloy, utilizing coated wire electrical discharge machining (WEDM) linked with Multi-Agent Deep Reinforcement Learning (MADRL). A Box–Behnken experimental design was adopted to gather baseline data for pulse-on time, pulse-off time, servo voltage, and peak current. The MADRL architecture combines cooperative agents to improve MRR, surface roughness, and kerf width concurrently. Beyond performance increase, the sustainability parameters of energy consumption, dielectric fluid use, and wire consumption were also studied. The proposed MADRL significantly improved the material removal rate (MRR) from 1.00 to 1.28 mm3/min and reduced the average surface roughness (Ra) from 1.95 to 1.66 µm, the kerf width from 0.27 to 0.24 mm, and the energy consumption from 122 to 107 J. The results show the potential of the proposed framework for adaptive, sustainable, and high-performance aerospace manufacturing.
- 11 June 2026
- Published by Springer Nature in Sādhanā
- Vol. 51 (3)
Multi-criteria optimization of wire-cut EDM parameters of titanium (Ti6Al4V) alloy using AHP-TOPSIS method
- 11 June 2026
- Published by Springer Nature in Sādhanā
- Vol. 51 (3)
Multi-criteria optimization of wire-cut EDM parameters of titanium (Ti6Al4V) alloy using AHP-TOPSIS method
- Open Access
- 28 February 2026
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 1 (42) , 112-119
Sustainable Production of ZnO Nanoparticles from Trianthema Portulacastrum and Their Efficacy against Pathogenic Microbes
This research investigates the eco-friendly manufacture of zinc oxide nanoparticles utilising the leaf extract of Trianthema portulacastrum, a medicinal plant recognized for its bioactive phytochemicals. The synthesis process avoids harmful ingredients, conforming to sustainable and environmentally responsible procedures. Thorough structural and chemical evaluations utilising FTIR, UV-Vis spectroscopy, SEM, DLS, and XRD confirmed the successful production of stable ZnO nanoparticles, which have a distinct hexagonal wurtzite crystal structure and surfaces functionalized by plant-derived proteins. The UV-Vis spectrum exhibited a red-shifted absorption, signifying distinctive optical characteristics. The DLS data indicated moderate aggregation with a hydrodynamic diameter of approximately 97.8 nm. The antibacterial efficiency was assessed against various pathogenic strains, demonstrating substantial inhibitory zones, particularly surpassing traditional medications in effectiveness against Mycobacterium tuberculosis.
- 28 February 2026
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 1 (42) , 112-119
Open AccessSustainable Production of ZnO Nanoparticles from Trianthema Portulacastrum and Their Efficacy against Pathogenic Microbes
This research investigates the eco-friendly manufacture of zinc oxide nanoparticles utilising the leaf extract of Trianthema portulacastrum, a medicinal plant recognized for its bioactive phytochemicals. The synthesis process avoids harmful ingredients, conforming to sustainable and environmentally responsible procedures. Thorough structural and chemical evaluations utilising FTIR, UV-Vis spectroscopy, SEM, DLS, and XRD confirmed the successful production of stable ZnO nanoparticles, which have a distinct hexagonal wurtzite crystal structure and surfaces functionalized by plant-derived proteins. The UV-Vis spectrum exhibited a red-shifted absorption, signifying distinctive optical characteristics. The DLS data indicated moderate aggregation with a hydrodynamic diameter of approximately 97.8 nm. The antibacterial efficiency was assessed against various pathogenic strains, demonstrating substantial inhibitory zones, particularly surpassing traditional medications in effectiveness against Mycobacterium tuberculosis.
- Open Access
- 4 March 2025
- Published by Springer Nature in Discover Catalysis
- Vol. 2 (1) , 1-20
Green synthesis of metal nanoparticles from three medicinal plants: a review of environmental and health applications
- 4 March 2025
- Published by Springer Nature in Discover Catalysis
- Vol. 2 (1) , 1-20
Open AccessGreen synthesis of metal nanoparticles from three medicinal plants: a review of environmental and health applications
- Open Access
- 6 February 2025
- Published by Atlantis Press SARL
- p. 21-37
Green Grape Seed Extract-Mediated Synthesis of CuO Nanoparticles: Characterization and Enhanced Antibacterial Activity
- 6 February 2025
- Published by Atlantis Press SARL
- p. 21-37
Open AccessGreen Grape Seed Extract-Mediated Synthesis of CuO Nanoparticles: Characterization and Enhanced Antibacterial Activity
- Open Access
Investigating and Multi-Objective Optimizing WEDM Parameters for Al6061/Mg/MoS2 Composites Using BBD and NSGA-II
This study aims to optimize the Wire Electrical Discharge Machining (EDM) process parameters for aluminum 6061 alloy reinforced with Mg and MoS2 using the Box–Behnken (BBD) design and the non-dominated sorting genetic (NSGA-II) algorithm. The objective is to enhance the machining efficiency and quality of the composite material. The Box–Behnken (BBD) design was utilized to design a set of experiments with varying levels of process parameters, comprising pulse-on time, servo volt, and current. The material removal rate and surface roughness were considered as machining responses for optimization. These responses were measured and used to develop a mathematical model. The NSGA-II, a multi-objective optimization algorithm, was then applied to search for the optimal combination of process parameters that simultaneously maximizes the material removal rate and minimizes the electrode wear rate and surface roughness. The algorithm generated and evolved a set of Pareto-optimal solutions, providing a trade-off between conflicting objectives. The results of the optimization process were analyzed to identify the optimal process parameters that lead to improved machining performance. The study revealed optimal Wire Electrical Discharge Machining (WEDM) parameters for Al6061/Mg/MoS2 composites using NSGA-II. The optimized parameters, including a pulse-on time (Ton) of 105 µs, servo voltage (SV) of 35 V, and peak current (PC) of 31 A, resulted in a Material Removal Rate (MRR) of 7.51 mm3/min and a surface roughness (SR) of 1.97 µm. This represents a 15% improvement in the MRR and a 20% reduction in the SR compared to non-optimized settings, demonstrating the efficiency of the BBD-NSGA-II approach.
Open AccessInvestigating and Multi-Objective Optimizing WEDM Parameters for Al6061/Mg/MoS2 Composites Using BBD and NSGA-II
This study aims to optimize the Wire Electrical Discharge Machining (EDM) process parameters for aluminum 6061 alloy reinforced with Mg and MoS2 using the Box–Behnken (BBD) design and the non-dominated sorting genetic (NSGA-II) algorithm. The objective is to enhance the machining efficiency and quality of the composite material. The Box–Behnken (BBD) design was utilized to design a set of experiments with varying levels of process parameters, comprising pulse-on time, servo volt, and current. The material removal rate and surface roughness were considered as machining responses for optimization. These responses were measured and used to develop a mathematical model. The NSGA-II, a multi-objective optimization algorithm, was then applied to search for the optimal combination of process parameters that simultaneously maximizes the material removal rate and minimizes the electrode wear rate and surface roughness. The algorithm generated and evolved a set of Pareto-optimal solutions, providing a trade-off between conflicting objectives. The results of the optimization process were analyzed to identify the optimal process parameters that lead to improved machining performance. The study revealed optimal Wire Electrical Discharge Machining (WEDM) parameters for Al6061/Mg/MoS2 composites using NSGA-II. The optimized parameters, including a pulse-on time (Ton) of 105 µs, servo voltage (SV) of 35 V, and peak current (PC) of 31 A, resulted in a Material Removal Rate (MRR) of 7.51 mm3/min and a surface roughness (SR) of 1.97 µm. This represents a 15% improvement in the MRR and a 20% reduction in the SR compared to non-optimized settings, demonstrating the efficiency of the BBD-NSGA-II approach.
- Open Access
- 31 October 2024
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 40 (5) , 1290-1296
Nanoalumina Synthesized from Solanum torvum Leaves: A Green Approach
This study investigates the eco-friendly synthesis of aluminum oxide nanoparticles (Al2O3 NPs) using Solanum torvum leaf extract, highlighting its potential in sustainable nanotechnology. The synthesized nanoparticles, with an average size of 94.6 nm, exhibited high crystallinity and diverse morphologies as confirmed through Scanning Electron Microscopy and X-ray crystallography. The antibacterial properties of these Al2O3 NPs were evaluated against a range of pathogens, including Escherichia coli and Candida albicans, where significant inhibition zones were observed. The findings underscore the effectiveness of Solanum torvum leaf extract as a green synthesis medium for producing Al2O3 nanoparticles. With their promising antibacterial activity, these nanoparticles hold potential for application in various fields, from healthcare to environmental protection, contributing to the development of environmentally friendly and sustainable nanomaterials.
- 31 October 2024
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 40 (5) , 1290-1296
Open AccessNanoalumina Synthesized from Solanum torvum Leaves: A Green Approach
This study investigates the eco-friendly synthesis of aluminum oxide nanoparticles (Al2O3 NPs) using Solanum torvum leaf extract, highlighting its potential in sustainable nanotechnology. The synthesized nanoparticles, with an average size of 94.6 nm, exhibited high crystallinity and diverse morphologies as confirmed through Scanning Electron Microscopy and X-ray crystallography. The antibacterial properties of these Al2O3 NPs were evaluated against a range of pathogens, including Escherichia coli and Candida albicans, where significant inhibition zones were observed. The findings underscore the effectiveness of Solanum torvum leaf extract as a green synthesis medium for producing Al2O3 nanoparticles. With their promising antibacterial activity, these nanoparticles hold potential for application in various fields, from healthcare to environmental protection, contributing to the development of environmentally friendly and sustainable nanomaterials.
- Open Access
- 28 February 2023
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 39 (1) , 172-178
Artificial Neural Network Prediction of Optimal Phenylic acid Adsorption using Lantana camara Activated Carbon
This paper exemplifies the application of artificial neural network (ANN) for prediction of performances in adsorption of phenylic acid from waste water by conventional and low cost Lantana camara activated carbon as adsorbent material. To estimate the removal efficiencies of phenylic acid, a three-layer feed-forward neural network using a back propagation algorithm was utilised in the MATLAB environment. The initial concentrations (mg/L) of phenylic acid, amount (g/L) of adsorbent and pH are the input parameters utilised to train the neural network. The output of the neural network was taken to be the effectiveness of phenylic acid removal. Statistical measures like root mean square error and linear regression were also used to evaluate the effectiveness of the proposed ANN models. Based on the comparison of the removal efficiencies of contaminants using ANN models and empirical results, ANN modelling for the adsorption of phenolic compounds was found to be reasonably consistent with the empirical results.
- 28 February 2023
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 39 (1) , 172-178
Open AccessArtificial Neural Network Prediction of Optimal Phenylic acid Adsorption using Lantana camara Activated Carbon
This paper exemplifies the application of artificial neural network (ANN) for prediction of performances in adsorption of phenylic acid from waste water by conventional and low cost Lantana camara activated carbon as adsorbent material. To estimate the removal efficiencies of phenylic acid, a three-layer feed-forward neural network using a back propagation algorithm was utilised in the MATLAB environment. The initial concentrations (mg/L) of phenylic acid, amount (g/L) of adsorbent and pH are the input parameters utilised to train the neural network. The output of the neural network was taken to be the effectiveness of phenylic acid removal. Statistical measures like root mean square error and linear regression were also used to evaluate the effectiveness of the proposed ANN models. Based on the comparison of the removal efficiencies of contaminants using ANN models and empirical results, ANN modelling for the adsorption of phenolic compounds was found to be reasonably consistent with the empirical results.
- Open Access
- 28 February 2023
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 39 (1) , 161-166
Oxidation of few Substituted Phenols and Reaction Mechanism by Heterocyclic Pyrazinium Chlorochromate and It's Biological Activity
The current investigation focuses on the oxidation of phenol (Phenylic acid) and a few mono substituted phenols in a liquified ethanoic acid medium with pyrazinium chorochromate (PzCC) support. The reaction showed a first kinetic model in PzCC but a fractional order in phenols. The low dielectric constant of the process, which is helped by hydrogen ions, promotes the reaction. The reaction's speed is unaffected by an increase in ionic strength. Meta-substituted phenols, which rely on the field effect for oxidation, are more susceptible to the delocalized effect than para-substituted phenols. The positive proportionality constant (ρ) indicates the presence of an electron deficit reaction site in the slow stage. Non-linearity in the Hammett plot was seen for all of the substituted phenols. An efficient mechanism and rate law were proposed following the computation of the activation and thermodynamic variables. Several gram positive and gram negative, including Entrococcus, Proteus vulgaris, Mycobacterium tuberculosis, and fungi, including A. niger, Fusarium, and Trichoderma, were examined for the antibacterial activity of the compound PzCC using the agar well diffusion method.
- 28 February 2023
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 39 (1) , 161-166
Open AccessOxidation of few Substituted Phenols and Reaction Mechanism by Heterocyclic Pyrazinium Chlorochromate and It's Biological Activity
The current investigation focuses on the oxidation of phenol (Phenylic acid) and a few mono substituted phenols in a liquified ethanoic acid medium with pyrazinium chorochromate (PzCC) support. The reaction showed a first kinetic model in PzCC but a fractional order in phenols. The low dielectric constant of the process, which is helped by hydrogen ions, promotes the reaction. The reaction's speed is unaffected by an increase in ionic strength. Meta-substituted phenols, which rely on the field effect for oxidation, are more susceptible to the delocalized effect than para-substituted phenols. The positive proportionality constant (ρ) indicates the presence of an electron deficit reaction site in the slow stage. Non-linearity in the Hammett plot was seen for all of the substituted phenols. An efficient mechanism and rate law were proposed following the computation of the activation and thermodynamic variables. Several gram positive and gram negative, including Entrococcus, Proteus vulgaris, Mycobacterium tuberculosis, and fungi, including A. niger, Fusarium, and Trichoderma, were examined for the antibacterial activity of the compound PzCC using the agar well diffusion method.