Javier Manso-Morato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Javier Manso-Morato has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Vanesa Ortega-López
Department of Civil Engineering, University of Burgos, 09001 Burgos, Spain
12 shared publications - Víctor Revilla-Cuesta
Department of Civil Engineering, University of Burgos, 09001 Burgos, Spain
12 shared publications - Nerea Hurtado-Alonso
Department of Construction, Escuela Politécnica Superior, University of Burgos, c/ Villadiego s/n, 09001, Burgos, Spain
11 shared publications - Marta Skaf
Department of Construction, University of Burgos, 09001 Burgos, Spain
4 shared publications - Ana Belén Espinosa
Department of Construction, Escuela Politécnica Superior, University of Burgos, Burgos, Spain
3 shared publications - Flora Faleschini
University of Padua
3 shared publications
Latest Publications
- Open Access
- 10 July 2026
- Published by Elsevier in Structures
- Vol. 91
Non-destructive evaluation of concrete with high contents of mixed waste from wind-turbine blades
- 10 July 2026
- Published by Elsevier in Structures
- Vol. 91
Open AccessNon-destructive evaluation of concrete with high contents of mixed waste from wind-turbine blades
- 1 June 2026
- Published by IATED Academy in EDULEARN Proceedings
- Vol. 1, 0513
BUILDING THE FUTURE THROUGH RESEARCH INTO SUSTAINABLE CONCRETE AND WIND TURBINE BLADE WASTE IN EXCELLENCE-ORIENTED EDUCATION
- 1 June 2026
- Published by IATED Academy in EDULEARN Proceedings
- Vol. 1, 0513
BUILDING THE FUTURE THROUGH RESEARCH INTO SUSTAINABLE CONCRETE AND WIND TURBINE BLADE WASTE IN EXCELLENCE-ORIENTED EDUCATION
- Open Access
- 27 May 2026
- Published by Elsevier in Journal of Environmental Management
- Vol. 410, 130075
Technical feasibility of adding 20% wind turbine blade waste to concrete: Fresh, mechanical, deformational, and sustainability assessment
- 27 May 2026
- Published by Elsevier in Journal of Environmental Management
- Vol. 410, 130075
Open AccessTechnical feasibility of adding 20% wind turbine blade waste to concrete: Fresh, mechanical, deformational, and sustainability assessment
- Open Access
- 26 January 2026
- Published by Elsevier in Structures
- Vol. 85
Durability analysis of concrete mixes with raw-crushed wind-turbine blade and recycled concrete aggregate: A modeling approach
- 26 January 2026
- Published by Elsevier in Structures
- Vol. 85
Open AccessDurability analysis of concrete mixes with raw-crushed wind-turbine blade and recycled concrete aggregate: A modeling approach
- Open Access
- 15 July 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 111
Deepening the effect of selectively crushed wind-turbine blade on the dimensional stability and high-temperature resistance of concrete
- 15 July 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 111
Open AccessDeepening the effect of selectively crushed wind-turbine blade on the dimensional stability and high-temperature resistance of concrete
- Open Access
- 2 January 2025
- Published by Elsevier in Journal of Environmental Management
- Vol. 373, 123995
Management of wind-turbine blade waste as high-content concrete addition: Mechanical performance evaluation and life cycle assessment
- 2 January 2025
- Published by Elsevier in Journal of Environmental Management
- Vol. 373, 123995
Open AccessManagement of wind-turbine blade waste as high-content concrete addition: Mechanical performance evaluation and life cycle assessment
- Open Access
- 19 December 2024
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 25 (1) , 1-24
Optimization of cementitious mixes through response surface method: a systematic review
The pursuit of cement-based materials with enhanced mechanical performance in the construction industry involves formulating numerous mixtures with varied contents of raw materials. However, the scarcity or contamination of these materials demands optimization methods to minimize the number of trials required. Response Surface Methodology (RSM) is a statistical experimental optimization method with which relations between sets of factors and responses can be established. This systematic review aims to analyze the existing literature on RSM models developed to achieve optimum levels in cementitious mixes. Over 100 papers were analyzed in accordance with the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) format. A comprehensive review of the RSM analyses in those studies and their effectiveness is conducted, through the evaluation of their optimized factors and responses, the selection of their design models, their use of ANalysis Of VAriance (ANOVA), and the determination of their coefficients of determination (R 2). Factors such as water/cement ratio and binder content prevailed in most models, the predominant responses of which were, respectively, compressive strength and workability. Although the use of ANOVA is commonly used to demonstrate the validity of the models, the studies replicating the mix with optimal levels of all factors are necessary to validate the results. On the basis of this review and depending on the responses that need to be maximized or minimized, the application of RSM can clearly be very crucial when quantifying the effects of new raw materials, whether recovered waste or natural resources, on mix behaviour.
- 19 December 2024
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 25 (1) , 1-24
Open AccessOptimization of cementitious mixes through response surface method: a systematic review
The pursuit of cement-based materials with enhanced mechanical performance in the construction industry involves formulating numerous mixtures with varied contents of raw materials. However, the scarcity or contamination of these materials demands optimization methods to minimize the number of trials required. Response Surface Methodology (RSM) is a statistical experimental optimization method with which relations between sets of factors and responses can be established. This systematic review aims to analyze the existing literature on RSM models developed to achieve optimum levels in cementitious mixes. Over 100 papers were analyzed in accordance with the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) format. A comprehensive review of the RSM analyses in those studies and their effectiveness is conducted, through the evaluation of their optimized factors and responses, the selection of their design models, their use of ANalysis Of VAriance (ANOVA), and the determination of their coefficients of determination (R 2). Factors such as water/cement ratio and binder content prevailed in most models, the predominant responses of which were, respectively, compressive strength and workability. Although the use of ANOVA is commonly used to demonstrate the validity of the models, the studies replicating the mix with optimal levels of all factors are necessary to validate the results. On the basis of this review and depending on the responses that need to be maximized or minimized, the application of RSM can clearly be very crucial when quantifying the effects of new raw materials, whether recovered waste or natural resources, on mix behaviour.
- Open Access
- 19 December 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (12) , 540
Specific Design of a Self-Compacting Concrete with Raw-Crushed Wind-Turbine Blade
Wind-turbine blades pose significant disposal challenges in the wind-energy sector due to the increasing demand for wind farms. Therefore, this study researched the revaluation of Raw-Crushed Wind-Turbine Blade (RCWTB), obtained through a non-selective blade crushing process, as a partial substitute for aggregates in Self-Compacting Concrete (SCC). The aim was to determine the most adequate water/cement (w/c) ratio and amount of superplasticizing admixtures required to achieve adequate flowability and 7-day compressive strength in SCC for increasing proportions of RCWTB, through the production of more than 40 SCC mixes. The results reported that increasing RCWTB additions decreased the slump flow of SCC by 6.58% per 1% RCWTB on average, as well as the compressive strength, although a minimum value of 25 MPa was always reached. Following a multi-criteria decision-making analysis, a w/c ratio of 0.45 and a superplasticizer content of 2.8% of the cement mass were optimum to produce SCC with up to 2% RCWTB. A w/c ratio of 0.50 and an amount of superplasticizers of 4.0% and 4.6% were optimum to produce SCC with 3% and 4% RCWTB, respectively. Concrete mixes containing 5% RCWTB did not achieve self-compacting properties under any design condition. All modifications of the SCC mix design showed statistically significant effects according to an analysis of variance at a confidence level of 95%. Overall, this study confirms that the incorporation of RCWTB into SCC through a careful mix design is feasible in terms of flowability and compressive strength, opening a new research avenue for the recycling of wind-turbine blades as an SCC component.
- 19 December 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (12) , 540
Open AccessSpecific Design of a Self-Compacting Concrete with Raw-Crushed Wind-Turbine Blade
Wind-turbine blades pose significant disposal challenges in the wind-energy sector due to the increasing demand for wind farms. Therefore, this study researched the revaluation of Raw-Crushed Wind-Turbine Blade (RCWTB), obtained through a non-selective blade crushing process, as a partial substitute for aggregates in Self-Compacting Concrete (SCC). The aim was to determine the most adequate water/cement (w/c) ratio and amount of superplasticizing admixtures required to achieve adequate flowability and 7-day compressive strength in SCC for increasing proportions of RCWTB, through the production of more than 40 SCC mixes. The results reported that increasing RCWTB additions decreased the slump flow of SCC by 6.58% per 1% RCWTB on average, as well as the compressive strength, although a minimum value of 25 MPa was always reached. Following a multi-criteria decision-making analysis, a w/c ratio of 0.45 and a superplasticizer content of 2.8% of the cement mass were optimum to produce SCC with up to 2% RCWTB. A w/c ratio of 0.50 and an amount of superplasticizers of 4.0% and 4.6% were optimum to produce SCC with 3% and 4% RCWTB, respectively. Concrete mixes containing 5% RCWTB did not achieve self-compacting properties under any design condition. All modifications of the SCC mix design showed statistically significant effects according to an analysis of variance at a confidence level of 95%. Overall, this study confirms that the incorporation of RCWTB into SCC through a careful mix design is feasible in terms of flowability and compressive strength, opening a new research avenue for the recycling of wind-turbine blades as an SCC component.
- 1 July 2024
- Published by Coventry University, Lanchester Library
- Vol. 1, 188-199
SUITABILITY OF CONCRETE PRODUCED WITH HIGH CONTENTS OF CRUSHED WIND-TURBINE BLADE
Some of the first-installed wind turbines will have to be replaced soon, as they are approaching the end of their life span. These wind-turbine blades must be recycled, so their suitability to be added into concrete mixes as fibers is studied. Thus, a less-polluting fiber-reinforced concrete can be achieved, maintaining its mechanical behavior. To recycle numerous wind-turbine blades at an adequate rate, large amounts of waste need to be added into concrete. This study aims to find out the suitability of adding high amounts of this waste material (0% vol., 5% vol., and 10% vol.). Testing yielded a slight decrease in fresh density and a higher occluded air content, yet largely maintaining its suitability for structural use according to the compressive strength. The results showed that concrete with a high content of crushed wind-turbine blade is suitable for structural use, being it an effective solution to said current sustainability problems.
- 1 July 2024
- Published by Coventry University, Lanchester Library
- Vol. 1, 188-199
SUITABILITY OF CONCRETE PRODUCED WITH HIGH CONTENTS OF CRUSHED WIND-TURBINE BLADE
Some of the first-installed wind turbines will have to be replaced soon, as they are approaching the end of their life span. These wind-turbine blades must be recycled, so their suitability to be added into concrete mixes as fibers is studied. Thus, a less-polluting fiber-reinforced concrete can be achieved, maintaining its mechanical behavior. To recycle numerous wind-turbine blades at an adequate rate, large amounts of waste need to be added into concrete. This study aims to find out the suitability of adding high amounts of this waste material (0% vol., 5% vol., and 10% vol.). Testing yielded a slight decrease in fresh density and a higher occluded air content, yet largely maintaining its suitability for structural use according to the compressive strength. The results showed that concrete with a high content of crushed wind-turbine blade is suitable for structural use, being it an effective solution to said current sustainability problems.