Hsiao-Hsuan Wan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hsiao-Hsuan Wan has a total of 141 co-authors. Here are the top co-authors by number of shared publications:
- Fan Ren
Department of Chemical Engineering, University of Florida 3 , Gainesville, Florida 32611
50 shared publications - Chao-Ching Chiang
University of Florida
48 shared publications - Stephen. J. Pearton
Material Science and Engineering, University of Florida 3 , Gainesville, Florida 32611
46 shared publications - Jian-Sian Li
Department of Chemical Engineering, University of Florida 1 , Gainesville, Florida 32611
43 shared publications Fan Ren
University of Florida
13 shared publications- Aman Haque
Penn State University
12 shared publications
Latest Publications
- 28 August 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (5)
Determination of band offsets at the interfaces of NiO and Cr2O3 with InAlN
This work investigates the electronic band alignment of p-NiO/InAlN and p-Cr2O3/InAlN heterostructures for the application of achieving enhancement-mode (e-mode) InAlN-based high-electron-mobility transistors (HEMTs) using x-ray photoelectron spectroscopy (XPS), together with the Kraut method to extract the band alignment parameters from reference oxide films and InAlN HEMT structures. The extracted conduction and valence-band offsets of NiO/InAlN are 1.58 and 2.11 eV, respectively. For Cr2O3/InAlN, the extracted conduction and valence-band offsets are 2.07 and 3.13 eV, respectively. NiO and Cr2O3 thin films were deposited by reactive RF sputtering on metal-organic chemical vapor deposited In0.17Al0.83N HEMT structures grown on sapphire or SiC substrates. The energy bandgap of InAlN and Cr2O3 was determined from XPS energy-loss spectra to be 4.43 and 3.37 eV, respectively, while the energy bandgap of NiO was 3.9 eV, as reported in our previous work. Both heterostructures exhibited staggered type-II band alignment with large interfacial carrier barriers. The large valence-band offsets indicate strong hole confinement and suggest that both oxides are capable of electrostatically depleting the polarization-induced two-dimensional electron gas, thereby facilitating enhancement-mode (E-mode) HEMT operation through a positive threshold-voltage shift. Among the investigated oxides, Cr2O3 exhibited the larger valence- and conduction-band offsets, indicating stronger carrier-blocking capability and suggesting greater potential for suppressing gate leakage and achieving a more positive threshold voltage than the NiO/InAlN heterojunction.
- 28 August 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (5)
Determination of band offsets at the interfaces of NiO and Cr2O3 with InAlN
This work investigates the electronic band alignment of p-NiO/InAlN and p-Cr2O3/InAlN heterostructures for the application of achieving enhancement-mode (e-mode) InAlN-based high-electron-mobility transistors (HEMTs) using x-ray photoelectron spectroscopy (XPS), together with the Kraut method to extract the band alignment parameters from reference oxide films and InAlN HEMT structures. The extracted conduction and valence-band offsets of NiO/InAlN are 1.58 and 2.11 eV, respectively. For Cr2O3/InAlN, the extracted conduction and valence-band offsets are 2.07 and 3.13 eV, respectively. NiO and Cr2O3 thin films were deposited by reactive RF sputtering on metal-organic chemical vapor deposited In0.17Al0.83N HEMT structures grown on sapphire or SiC substrates. The energy bandgap of InAlN and Cr2O3 was determined from XPS energy-loss spectra to be 4.43 and 3.37 eV, respectively, while the energy bandgap of NiO was 3.9 eV, as reported in our previous work. Both heterostructures exhibited staggered type-II band alignment with large interfacial carrier barriers. The large valence-band offsets indicate strong hole confinement and suggest that both oxides are capable of electrostatically depleting the polarization-induced two-dimensional electron gas, thereby facilitating enhancement-mode (E-mode) HEMT operation through a positive threshold-voltage shift. Among the investigated oxides, Cr2O3 exhibited the larger valence- and conduction-band offsets, indicating stronger carrier-blocking capability and suggesting greater potential for suppressing gate leakage and achieving a more positive threshold voltage than the NiO/InAlN heterojunction.
- Open Access
- 1 August 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (8) , 085002
Effects of Gamma Irradiation on Electrical Characteristics and Carrier Dynamics in Diamond Schottky and Heterojunction Devices
Diamond-based devices are promising for operation in radiation environments due to their wide bandgap and strong atomic bonding. In this work, the effects of Co-60 gamma irradiation to a total dose of 1 Mrad on the electrical characteristics and carrier dynamics of diamond Schottky and indium-tin oxide (ITO)/boron doped diamond heterojunction rectifiers are investigated. The rectifiers were exposed to gamma radiation with photon energies of 1.17 and 1.33 MeV, where ionization dominates over displacement damage. The Schottky diodes exhibit minimal changes in both forward and reverse current characteristics after irradiation, indicating stable metal/diamond interfaces. In contrast, the heterojunction devices show a positive shift of forward IV around the diode turn-on voltage and an increased ideality factor, suggesting modification of charge accumulation in the ITO. The changes in electrical characteristics for both rectifiers are reversible by application of short forward current pulses during repeated measurement of the current–voltage characteristics at room temperature. There are no permanent total ionizing dose effects present in the rectifiers under the irradiation conditions used in this study. Reverse current shows only minor variation for both types of rectifiers, confirming the absence of significant bulk leakage paths. Reverse recovery measurements reveal a reduction in recovery time after irradiation, attributed to decreased carrier lifetime and reduced stored charge due to radiation-induced traps. The extracted carrier concentration from the capacitance–voltage analysis changes only slightly from 1.23 × 10 16 to 1.20 × 10 16 cm −3 after irradiation confirming that gamma irradiation does not induce measurable degradation in bulk electrical properties under the irradiation conditions used in this study. While isolated Frenkel defects or other point defects may be generated during gamma irradiation, their concentration is evidently too low to produce measurable changes in carrier concentration or leakage current. The corresponding carrier removal rate is on the order of ∼0.1 cm −1 . This small variation indicates that gamma irradiation does not significantly affect the bulk carrier concentration in diamond. These results indicate that gamma irradiation primarily affects carrier dynamics and interface properties, while the bulk diamond remains largely unaffected. Thus, diamond-based rectifiers may be well-suited to harsh terrestrial and space radiation applications if appropriate bias sequences are implemented to reverse the radiation-induced changes.
- 1 August 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (8) , 085002
Open AccessEffects of Gamma Irradiation on Electrical Characteristics and Carrier Dynamics in Diamond Schottky and Heterojunction Devices
Diamond-based devices are promising for operation in radiation environments due to their wide bandgap and strong atomic bonding. In this work, the effects of Co-60 gamma irradiation to a total dose of 1 Mrad on the electrical characteristics and carrier dynamics of diamond Schottky and indium-tin oxide (ITO)/boron doped diamond heterojunction rectifiers are investigated. The rectifiers were exposed to gamma radiation with photon energies of 1.17 and 1.33 MeV, where ionization dominates over displacement damage. The Schottky diodes exhibit minimal changes in both forward and reverse current characteristics after irradiation, indicating stable metal/diamond interfaces. In contrast, the heterojunction devices show a positive shift of forward IV around the diode turn-on voltage and an increased ideality factor, suggesting modification of charge accumulation in the ITO. The changes in electrical characteristics for both rectifiers are reversible by application of short forward current pulses during repeated measurement of the current–voltage characteristics at room temperature. There are no permanent total ionizing dose effects present in the rectifiers under the irradiation conditions used in this study. Reverse current shows only minor variation for both types of rectifiers, confirming the absence of significant bulk leakage paths. Reverse recovery measurements reveal a reduction in recovery time after irradiation, attributed to decreased carrier lifetime and reduced stored charge due to radiation-induced traps. The extracted carrier concentration from the capacitance–voltage analysis changes only slightly from 1.23 × 10 16 to 1.20 × 10 16 cm −3 after irradiation confirming that gamma irradiation does not induce measurable degradation in bulk electrical properties under the irradiation conditions used in this study. While isolated Frenkel defects or other point defects may be generated during gamma irradiation, their concentration is evidently too low to produce measurable changes in carrier concentration or leakage current. The corresponding carrier removal rate is on the order of ∼0.1 cm −1 . This small variation indicates that gamma irradiation does not significantly affect the bulk carrier concentration in diamond. These results indicate that gamma irradiation primarily affects carrier dynamics and interface properties, while the bulk diamond remains largely unaffected. Thus, diamond-based rectifiers may be well-suited to harsh terrestrial and space radiation applications if appropriate bias sequences are implemented to reverse the radiation-induced changes.
- Open Access
- 6 July 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Pulsed-laser single-event effects study of AlN Schottky barrier diodes
Aluminum nitride (AlN) is an ultrawide-bandgap semiconductor with potential for radiation-hardened devices in extreme environments. This study investigates single-event effects in AlN Schottky barrier diodes (SBDs) using a pulsed-laser single-event effects technique, addressing a significant gap in AlN radiation effects research. Two types of lateral SBDs were employed for this study; in the first, Ti/Au and transparent Indium Tin Oxide (ITO) were used as the Ohmic and Schottky contacts, respectively, and in the second, ITO was used for both the Ohmic and Schottky contacts. SBDs were irradiated with 350 nm laser pulses, simulating ionizing radiation via two-photon absorption. Single-event transients were recorded, revealing fast decay constants (∼20 ps), suggesting high carrier recombination rates within the AlN material. Spatial scans showed maximum charge collection near the ITO Schottky contact edge, with significantly reduced collection under the ITO, attributed to lower laser light transmission. Increasing reverse bias and laser pulse energy led to an increased laser-induced leakage current. SBDs in this study underwent laser-induced catastrophic single-event burnout (SEB) at a reverse bias of 160 V, which is significantly below the 4 kV breakdown voltage. The findings highlight AlN’s vulnerability to single-event effects and the need for further investigation into its radiation response, including simulations and material characterization to understand electric field distributions, recombination center behavior, and SEB mechanisms.
- 6 July 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Open AccessPulsed-laser single-event effects study of AlN Schottky barrier diodes
Aluminum nitride (AlN) is an ultrawide-bandgap semiconductor with potential for radiation-hardened devices in extreme environments. This study investigates single-event effects in AlN Schottky barrier diodes (SBDs) using a pulsed-laser single-event effects technique, addressing a significant gap in AlN radiation effects research. Two types of lateral SBDs were employed for this study; in the first, Ti/Au and transparent Indium Tin Oxide (ITO) were used as the Ohmic and Schottky contacts, respectively, and in the second, ITO was used for both the Ohmic and Schottky contacts. SBDs were irradiated with 350 nm laser pulses, simulating ionizing radiation via two-photon absorption. Single-event transients were recorded, revealing fast decay constants (∼20 ps), suggesting high carrier recombination rates within the AlN material. Spatial scans showed maximum charge collection near the ITO Schottky contact edge, with significantly reduced collection under the ITO, attributed to lower laser light transmission. Increasing reverse bias and laser pulse energy led to an increased laser-induced leakage current. SBDs in this study underwent laser-induced catastrophic single-event burnout (SEB) at a reverse bias of 160 V, which is significantly below the 4 kV breakdown voltage. The findings highlight AlN’s vulnerability to single-event effects and the need for further investigation into its radiation response, including simulations and material characterization to understand electric field distributions, recombination center behavior, and SEB mechanisms.
- Open Access
- 1 July 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (7) , 075004
Electron Beam Irradiation-Induced Transport and Recombination in P-type Diamond Diodes
This study investigates minority carrier diffusion length ( L ) and defect-mediated recombination phenomena in boron-doped p-type diamond epitaxial layers. Utilizing temperature-dependent electron beam-induced current (EBIC) and cathodoluminescence (CL), the influence of temperature and sustained electron beam irradiation was characterized. The diamond sample demonstrates a pronounced thermal enhancement to the minority carrier diffusion length. This temperature enhancement for L has an activation energy of 177 meV. Furthermore, sustained electron injection induces a near-linear elongation of the diffusion length through passivation of deep-level defects. From the EBIC injection data, an activation energy of 151 meV was extracted from fitting. Temperature-resolved CL reveals the quenching of the characteristic A-band emission at 100 °C. Additionally, a thermal activation energy of 112 meV was extracted via a decay fit of the temperature dependent CL intensity data. While sustained electron beam irradiation reveals dose-dependent quenching of the A-band emission with thermally activated decay rates. This yields activation energies of 110 meV and 11 meV associated with distinct defect generation mechanisms at high and low temperatures, respectively. This provides a complementary assessment of the defect landscape governing minority carrier lifetimes in these boron-doped diamond diodes.
- 1 July 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (7) , 075004
Open AccessElectron Beam Irradiation-Induced Transport and Recombination in P-type Diamond Diodes
This study investigates minority carrier diffusion length ( L ) and defect-mediated recombination phenomena in boron-doped p-type diamond epitaxial layers. Utilizing temperature-dependent electron beam-induced current (EBIC) and cathodoluminescence (CL), the influence of temperature and sustained electron beam irradiation was characterized. The diamond sample demonstrates a pronounced thermal enhancement to the minority carrier diffusion length. This temperature enhancement for L has an activation energy of 177 meV. Furthermore, sustained electron injection induces a near-linear elongation of the diffusion length through passivation of deep-level defects. From the EBIC injection data, an activation energy of 151 meV was extracted from fitting. Temperature-resolved CL reveals the quenching of the characteristic A-band emission at 100 °C. Additionally, a thermal activation energy of 112 meV was extracted via a decay fit of the temperature dependent CL intensity data. While sustained electron beam irradiation reveals dose-dependent quenching of the A-band emission with thermally activated decay rates. This yields activation energies of 110 meV and 11 meV associated with distinct defect generation mechanisms at high and low temperatures, respectively. This provides a complementary assessment of the defect landscape governing minority carrier lifetimes in these boron-doped diamond diodes.
- 15 June 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (4)
O2/Ar inductively coupled plasma etching of boron-doped single-crystal diamond
Diamond is an attractive semiconductor for extreme-environment electronics due to its ultrawide bandgap, high breakdown field, and exceptional thermal conductivity. However, reliable microfabrication requires controllable dry etching techniques because diamond is chemically inert and difficult to pattern using conventional wet processes. In this work, the etching behavior of boron-doped single-crystal diamond was systematically investigated using an Ar/O2 inductively coupled plasma (ICP) process. The samples consisted of a 5 μm boron-doped epitaxial layer grown on a type IIa (001)-oriented single-crystal diamond substrate. The effects of oxygen fraction, RF bias power, and ICP source power on the etch rate and DC bias voltage were examined. The etch rate increased with oxygen concentration up to approximately 80% O2 and decreased at higher oxygen fractions, indicating that efficient etching requires both reactive oxygen species and ion-assisted bond breaking. Increasing RF bias power significantly enhanced the etch rate due to higher ion bombardment energy but also increased surface damage, as evidenced by an increased sp2 carbon component in x-ray photoelectron spectroscopy. Increasing ICP power enhanced plasma density and chemical etching while reducing ion bombardment energy. A threshold ion energy of approximately 67 eV was extracted from the RF-power series, indicating the minimum ion energy required to initiate efficient etching. Post-treatment studies showed that ozone effectively reduces sp2 carbon and recovers a more diamond-rich surface, while short N2 annealing is ineffective. These results provide insights into the interplay between ion-assisted and chemical mechanisms in diamond etching and offer guidance for optimizing plasma processes for diamond device fabrication.
- 15 June 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (4)
O2/Ar inductively coupled plasma etching of boron-doped single-crystal diamond
Diamond is an attractive semiconductor for extreme-environment electronics due to its ultrawide bandgap, high breakdown field, and exceptional thermal conductivity. However, reliable microfabrication requires controllable dry etching techniques because diamond is chemically inert and difficult to pattern using conventional wet processes. In this work, the etching behavior of boron-doped single-crystal diamond was systematically investigated using an Ar/O2 inductively coupled plasma (ICP) process. The samples consisted of a 5 μm boron-doped epitaxial layer grown on a type IIa (001)-oriented single-crystal diamond substrate. The effects of oxygen fraction, RF bias power, and ICP source power on the etch rate and DC bias voltage were examined. The etch rate increased with oxygen concentration up to approximately 80% O2 and decreased at higher oxygen fractions, indicating that efficient etching requires both reactive oxygen species and ion-assisted bond breaking. Increasing RF bias power significantly enhanced the etch rate due to higher ion bombardment energy but also increased surface damage, as evidenced by an increased sp2 carbon component in x-ray photoelectron spectroscopy. Increasing ICP power enhanced plasma density and chemical etching while reducing ion bombardment energy. A threshold ion energy of approximately 67 eV was extracted from the RF-power series, indicating the minimum ion energy required to initiate efficient etching. Post-treatment studies showed that ozone effectively reduces sp2 carbon and recovers a more diamond-rich surface, while short N2 annealing is ineffective. These results provide insights into the interplay between ion-assisted and chemical mechanisms in diamond etching and offer guidance for optimizing plasma processes for diamond device fabrication.
- Open Access
- 1 June 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (6) , 065001
Stability Study of >13.5 kV Field Plated NiO/ β -Ga 2 O 3 Heterojunction Rectifiers Fabricated on 4-Inch Wafers
100 μm diameter vertical NiO/ β -Ga 2 O 3 heterojunction diodes with dielectric-assisted field-plate edge termination were fabricated on a 4-inch β -Ga 2 O 3 wafer with ∼10–14 μm thick Si-doped 8.5 × 10 15 cm −3 drift layers demonstrating breakdown voltages (V B ) exceeding 13.5 kV, limited by the measurement equipment, on-voltage (V ON ) of ∼2.2 V and on-state resistance R ON of 5.5 mΩ·cm 2 . The average critical breakdown field in heterojunctions was 9.6–13.5 MV cm −1 , within the reported theoretical value range from 8–15 MV cm −1 for β -Ga 2 O 3 . The associated maximum power figure-of-merit, V B 2 /R ON of >33.1 GW cm −2 was achieved. Scanning transmission electron microscopy (STEM) reveals a polycrystalline NiO layer with multiple crystallographic orientations and a well-defined device stack. Forward current–voltage measurements performed 10 days and 150 days after NiO deposition show stable turn-on behavior with only minor changes in low-bias current. Cross-sectional STEM and energy-dispersive X-ray spectroscopy (EDS) analysis reveal localized oxygen enrichment near the outer edge (∼500 nm) of the Ni contact on NiO, likely associated with fabrication-related oxidation, while the NiO/ β -Ga 2 O 3 heterojunction remains intact. These results demonstrate stable ultra-high-voltage operation of NiO/ β -Ga 2 O 3 heterojunction rectifiers fabricated on wafer-scale substrates, highlighting their potential for next-generation extreme-voltage power electronics.
- 1 June 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (6) , 065001
Open AccessStability Study of >13.5 kV Field Plated NiO/ β -Ga 2 O 3 Heterojunction Rectifiers Fabricated on 4-Inch Wafers
100 μm diameter vertical NiO/ β -Ga 2 O 3 heterojunction diodes with dielectric-assisted field-plate edge termination were fabricated on a 4-inch β -Ga 2 O 3 wafer with ∼10–14 μm thick Si-doped 8.5 × 10 15 cm −3 drift layers demonstrating breakdown voltages (V B ) exceeding 13.5 kV, limited by the measurement equipment, on-voltage (V ON ) of ∼2.2 V and on-state resistance R ON of 5.5 mΩ·cm 2 . The average critical breakdown field in heterojunctions was 9.6–13.5 MV cm −1 , within the reported theoretical value range from 8–15 MV cm −1 for β -Ga 2 O 3 . The associated maximum power figure-of-merit, V B 2 /R ON of >33.1 GW cm −2 was achieved. Scanning transmission electron microscopy (STEM) reveals a polycrystalline NiO layer with multiple crystallographic orientations and a well-defined device stack. Forward current–voltage measurements performed 10 days and 150 days after NiO deposition show stable turn-on behavior with only minor changes in low-bias current. Cross-sectional STEM and energy-dispersive X-ray spectroscopy (EDS) analysis reveal localized oxygen enrichment near the outer edge (∼500 nm) of the Ni contact on NiO, likely associated with fabrication-related oxidation, while the NiO/ β -Ga 2 O 3 heterojunction remains intact. These results demonstrate stable ultra-high-voltage operation of NiO/ β -Ga 2 O 3 heterojunction rectifiers fabricated on wafer-scale substrates, highlighting their potential for next-generation extreme-voltage power electronics.
- Open Access
- 1 June 2026
- Published by IOP Publishing in Journal of Physics: Materials
- Vol. 9 (3) , 035002
Room-temperature electrical processing of aluminum nitride heterojunction diodes
Ultra-wide-bandgap (UWBG) semiconductors are promising for power electronics, but high-breakdown diodes often suffer from high turn-on voltages and defect-related performance limits, requiring high-temperature processing. This work demonstrates that electron wind force (EWF)-assisted processing significantly reduces the turn-on voltage of aluminum nitride (AlN) diodes at room temperature, eliminating the need for thermal annealing. Across four room-temperature devices, the average turn-on voltage decreases from 2.34 ± 0.23 to 1.23 ± 0.38 V after EWF processing, while the forward current at 5 V increases from 78.23 ± 20.75 pA to 110.4 ± 20.8 pA. Infrared thermal imaging during processing shows that the sample temperature remains close to ambient, supporting the low-thermal-budget nature of the approach. High-frequency capacitance–voltage measurements reveal a systematic modification of junction electrostatics, indicating reorganization of electrically active defect states within the depletion region rather than changes in bulk conductivity. Complementary Raman spectroscopy shows a modest narrowing of the E 2 (high) phonon linewidth, from 5.04 to 4.82 cm -1 , reflecting reduced defect-related phonon scattering. Time-dependent measurements show partial relaxation of the turn-on voltage shift after four days, suggesting that the EWF-induced modification is metastable rather than conventional bulk lattice annealing. Together, these results show that room-temperature EWF processing provides an electrically driven route to lowering the turn-on voltage of AlN diodes, addressing a key limitation in UWBG rectifiers.
- 1 June 2026
- Published by IOP Publishing in Journal of Physics: Materials
- Vol. 9 (3) , 035002
Open AccessRoom-temperature electrical processing of aluminum nitride heterojunction diodes
Ultra-wide-bandgap (UWBG) semiconductors are promising for power electronics, but high-breakdown diodes often suffer from high turn-on voltages and defect-related performance limits, requiring high-temperature processing. This work demonstrates that electron wind force (EWF)-assisted processing significantly reduces the turn-on voltage of aluminum nitride (AlN) diodes at room temperature, eliminating the need for thermal annealing. Across four room-temperature devices, the average turn-on voltage decreases from 2.34 ± 0.23 to 1.23 ± 0.38 V after EWF processing, while the forward current at 5 V increases from 78.23 ± 20.75 pA to 110.4 ± 20.8 pA. Infrared thermal imaging during processing shows that the sample temperature remains close to ambient, supporting the low-thermal-budget nature of the approach. High-frequency capacitance–voltage measurements reveal a systematic modification of junction electrostatics, indicating reorganization of electrically active defect states within the depletion region rather than changes in bulk conductivity. Complementary Raman spectroscopy shows a modest narrowing of the E 2 (high) phonon linewidth, from 5.04 to 4.82 cm -1 , reflecting reduced defect-related phonon scattering. Time-dependent measurements show partial relaxation of the turn-on voltage shift after four days, suggesting that the EWF-induced modification is metastable rather than conventional bulk lattice annealing. Together, these results show that room-temperature EWF processing provides an electrically driven route to lowering the turn-on voltage of AlN diodes, addressing a key limitation in UWBG rectifiers.
- 18 May 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (4)
NiO/Ga2O3 heterojunction rectifiers with >8.1 kV breakdown enabled by optimized field plate configuration
Vertical Ga2O3 heterojunction diodes were fabricated and systematically studied to evaluate the impact of lateral contact geometry on forward and reverse device performance. The devices were formed on 32 μm thick, lightly doped (8.6 × 1015 cm−3) β-Ga2O3 drift layers grown by halide vapor phase epitaxy on heavily doped n+ substrates. A NiO/Ni/Au heterojunction anode was employed together with dielectric edge termination using a 70 nm SiO2/30 nm SiN field-plate structure. Three device designs with different field plate dimensions (D = 10, 20, and 30 μm) between the first- and second-layer contact metals were investigated. Capacitance–voltage measurements indicate a free carrier concentration of approximately (8.6 ± 1.2) × 1015 cm−3 in the drift layer, while forward I–V characteristics showed comparable saturation currents and turn-on voltages for all designs. Increasing D resulted in a reduction in on-resistance and a significant suppression of reverse leakage current at low to moderate reverse bias. The optimized device with D = 30 μm exhibited the highest breakdown voltage of approximately 8.1 kV, compared with 5.5 and 4.5 kV for D = 20 μm and D = 10 μm, respectively. These results demonstrate that lateral contact spacing is a critical design parameter for electric-field management and breakdown enhancement in Ga2O3 heterojunction diodes.
- 18 May 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (4)
NiO/Ga2O3 heterojunction rectifiers with >8.1 kV breakdown enabled by optimized field plate configuration
Vertical Ga2O3 heterojunction diodes were fabricated and systematically studied to evaluate the impact of lateral contact geometry on forward and reverse device performance. The devices were formed on 32 μm thick, lightly doped (8.6 × 1015 cm−3) β-Ga2O3 drift layers grown by halide vapor phase epitaxy on heavily doped n+ substrates. A NiO/Ni/Au heterojunction anode was employed together with dielectric edge termination using a 70 nm SiO2/30 nm SiN field-plate structure. Three device designs with different field plate dimensions (D = 10, 20, and 30 μm) between the first- and second-layer contact metals were investigated. Capacitance–voltage measurements indicate a free carrier concentration of approximately (8.6 ± 1.2) × 1015 cm−3 in the drift layer, while forward I–V characteristics showed comparable saturation currents and turn-on voltages for all designs. Increasing D resulted in a reduction in on-resistance and a significant suppression of reverse leakage current at low to moderate reverse bias. The optimized device with D = 30 μm exhibited the highest breakdown voltage of approximately 8.1 kV, compared with 5.5 and 4.5 kV for D = 20 μm and D = 10 μm, respectively. These results demonstrate that lateral contact spacing is a critical design parameter for electric-field management and breakdown enhancement in Ga2O3 heterojunction diodes.
- 29 April 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (3)
Evaluating neutron induced displacement damage in gallium oxide based rectifiers
This study investigates the effects of reactor-neutron irradiation on the electrical characteristics of NiO/Ga2O3 heterojunction diodes (HJDs) and Ni/Ga2O3 Schottky barrier diodes (SBDs) for 1 MeV (Ga2O3) equivalent neutron fluences from 6.17×1011 to 6.17×1014 n/cm2. The novel contribution of this research is the comparison of SBD and HJD diodes, with and without edge termination, and the development of a dose-response relationship for carrier concentration reduction in gallium oxide diodes. Capacitance-voltage (C-V) characterization enabled a determination of the spatially dependent carrier removal rate. Forward current-voltage (I-V) characteristics were used to compare changes in the ideality factor and series resistance. The ideality factor was unaffected by irradiation, while the series resistance increased sharply after a fluence of 2.47×1014 n/cm2.
- 29 April 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (3)
Evaluating neutron induced displacement damage in gallium oxide based rectifiers
This study investigates the effects of reactor-neutron irradiation on the electrical characteristics of NiO/Ga2O3 heterojunction diodes (HJDs) and Ni/Ga2O3 Schottky barrier diodes (SBDs) for 1 MeV (Ga2O3) equivalent neutron fluences from 6.17×1011 to 6.17×1014 n/cm2. The novel contribution of this research is the comparison of SBD and HJD diodes, with and without edge termination, and the development of a dose-response relationship for carrier concentration reduction in gallium oxide diodes. Capacitance-voltage (C-V) characterization enabled a determination of the spatially dependent carrier removal rate. Forward current-voltage (I-V) characteristics were used to compare changes in the ideality factor and series resistance. The ideality factor was unaffected by irradiation, while the series resistance increased sharply after a fluence of 2.47×1014 n/cm2.
- Open Access
- 9 March 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (3)
Impact of 10 MeV Proton Irradiation on the Electrical Characteristics of Diamond Schottky and Heterojunction Diodes
The radiation tolerance of single-crystal diamond devices was investigated under 10 MeV proton irradiation. Schottky barrier diodes (SBDs) and ITO/diamond heterojunction diodes were fabricated on boron-doped diamond substrates with a 10 µm lightly doped drift layer and exposed to proton fluences from 1.0 × 10¹³ to 1.6 × 10¹⁴ cm⁻². Irradiation induced increased on-resistance, reduced saturation current, and enhanced reverse leakage, with heterojunction devices showing greater degradation due to the vulnerability of the ITO layer and interface. Capacitance–voltage measurements revealed carrier removal rates of 171, 65, and 43 cm⁻¹ for fluences of 1.0 × 10¹³, 6.0 × 10¹³, and 1.6 × 10¹⁴ cm⁻², respectively, confirming diamond’s superior radiation hardness compared to Si, GaN, and Ga₂O₃. This resilience is attributed to diamond’s high atomic displacement energy, which limits lattice damage. These results demonstrate the potential of single-crystal diamond devices for radiation-hard power electronics and high-radiation environments.
- 9 March 2026
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 15 (3)
Open AccessImpact of 10 MeV Proton Irradiation on the Electrical Characteristics of Diamond Schottky and Heterojunction Diodes
The radiation tolerance of single-crystal diamond devices was investigated under 10 MeV proton irradiation. Schottky barrier diodes (SBDs) and ITO/diamond heterojunction diodes were fabricated on boron-doped diamond substrates with a 10 µm lightly doped drift layer and exposed to proton fluences from 1.0 × 10¹³ to 1.6 × 10¹⁴ cm⁻². Irradiation induced increased on-resistance, reduced saturation current, and enhanced reverse leakage, with heterojunction devices showing greater degradation due to the vulnerability of the ITO layer and interface. Capacitance–voltage measurements revealed carrier removal rates of 171, 65, and 43 cm⁻¹ for fluences of 1.0 × 10¹³, 6.0 × 10¹³, and 1.6 × 10¹⁴ cm⁻², respectively, confirming diamond’s superior radiation hardness compared to Si, GaN, and Ga₂O₃. This resilience is attributed to diamond’s high atomic displacement energy, which limits lattice damage. These results demonstrate the potential of single-crystal diamond devices for radiation-hard power electronics and high-radiation environments.