Lauren Dallachiesa
Research Subjects
Lauren Dallachiesa has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Roland Ryf
Nokia Bell Labs
10 shared publications - Haoshuo Chen
Nokia Bell Labs
8 shared publications - Mikael Mazur
Nokia Bell Labs
8 shared publications - Nicolas Keith Fontaine
Nokia Bell Labs
8 shared publications - David T. Neilson
Nokia Bell Labs, New Providence, NJ, USA
7 shared publications Roland Ryf
6 shared publications
Latest Publications
- Open Access
- 10 June 2026
- Published by Copernicus GmbH
Observations of P-wave phase arrivals from major earthquakes with the IRIS fiber-opticsubsea cable connecting Iceland and Ireland
Approximately 70% of the Earth's surface is covered by the oceans. Installing permanent seismic sensors on the seafloor is both difficult and costly, resulting in a gap in the the global seismic monitoring. Recently, the potential of using the existing network of submarine fiber-optic cables for the observation of seismic waves has been investigated, several works demonstrating the feasibility of using trans-oceanic subsea cables as seismic sensors (f.ex. Marra 2018,2022; Zhan, 2021; Mazur 2024). In this work, we use a distributed fiber optic sensing (DFOS) prototype capable of measuring the integrated strain between each repeater along the entire length of a fiber optic cable (the repeaters are typically placed 100 km from each other). This instrument is used on the IRIS telecommunication cable, an operational subsea cable connecting Iceland to Ireland, transforming 17 spans of the cable into an array of 17 individual seismic sensors. Signals from several large earthquakes can be observed on the recorded data from the cable and surface waves as well as multiple seismic body wave phases can be tracked across the spans.To assess the capability of the monitoring system to detect the P-wave phase, we use an STA-LTA algorithm to automatically detect the arrival of P-waves in the data and we compare the phase detections to those predicted by travel-time curves from a catalogue of major earthquakes from the USGS database (with a magnitude above 6 and a distance of 30 to 100° from the fiber-optic subsea cable). We manage to retrieve 40% of our earthquake catalogue with our detection algorithm. However, a large part of our detections are not pickings of the P-wave phase.
- 10 June 2026
- Published by Copernicus GmbH
Open AccessObservations of P-wave phase arrivals from major earthquakes with the IRIS fiber-opticsubsea cable connecting Iceland and Ireland
Approximately 70% of the Earth's surface is covered by the oceans. Installing permanent seismic sensors on the seafloor is both difficult and costly, resulting in a gap in the the global seismic monitoring. Recently, the potential of using the existing network of submarine fiber-optic cables for the observation of seismic waves has been investigated, several works demonstrating the feasibility of using trans-oceanic subsea cables as seismic sensors (f.ex. Marra 2018,2022; Zhan, 2021; Mazur 2024). In this work, we use a distributed fiber optic sensing (DFOS) prototype capable of measuring the integrated strain between each repeater along the entire length of a fiber optic cable (the repeaters are typically placed 100 km from each other). This instrument is used on the IRIS telecommunication cable, an operational subsea cable connecting Iceland to Ireland, transforming 17 spans of the cable into an array of 17 individual seismic sensors. Signals from several large earthquakes can be observed on the recorded data from the cable and surface waves as well as multiple seismic body wave phases can be tracked across the spans.To assess the capability of the monitoring system to detect the P-wave phase, we use an STA-LTA algorithm to automatically detect the arrival of P-waves in the data and we compare the phase detections to those predicted by travel-time curves from a catalogue of major earthquakes from the USGS database (with a magnitude above 6 and a distance of 30 to 100° from the fiber-optic subsea cable). We manage to retrieve 40% of our earthquake catalogue with our detection algorithm. However, a large part of our detections are not pickings of the P-wave phase.
- Open Access
- 15 March 2025
- Published by Copernicus GmbH
Observations of earthquakes on multiple spans of the IRIS subsea fiber-optic cable connecting Iceland and Ireland
About 70% of the Earth's surface is covered by ocean, making observations of seismic waves difficult and expensive in vast regions. Recently, seismic waves have been observed using transmission fiber-optic sensing on trans-oceanic subsea cables, making them an exciting potential addition to global seismic networks (f.ex. Marra 2018,2022; Zhan, 2021; Mazur 2024). In this work we use a distributed fiber optic sensing (DFOS) prototype capable of measuring the integrated strain between each repeater (typically 100 km) along the entire cable length, with each span acting as an effective sensor. This division allows for a separation of signals from different parts of the cable, leading to higher S/N ratios on quiet deep-water segments and more easily interpreted waveforms. We show signals from several large earthquakes registered on 17 spans of the IRIS subsea telecommunications cable, that connects Iceland and Ireland. Multiple seismic body-wave phases, as well as longer period surface waves, can be tracked across the spans, or the array of effective sensors. Comparing the observed phase arrivals to those predicted by travel-time curves, we show how different phases are visible on different segments as expected by the varying orientation of individual segments relative to the seismic wave field. Furthermore, we simulate the observed waveforms using a spectral-element wave propagation software (SPECFEM3D_GLOBE), following the theoretical development of Fichtner et al 2022, and compare to the observed waveforms.
- 15 March 2025
- Published by Copernicus GmbH
Open AccessObservations of earthquakes on multiple spans of the IRIS subsea fiber-optic cable connecting Iceland and Ireland
About 70% of the Earth's surface is covered by ocean, making observations of seismic waves difficult and expensive in vast regions. Recently, seismic waves have been observed using transmission fiber-optic sensing on trans-oceanic subsea cables, making them an exciting potential addition to global seismic networks (f.ex. Marra 2018,2022; Zhan, 2021; Mazur 2024). In this work we use a distributed fiber optic sensing (DFOS) prototype capable of measuring the integrated strain between each repeater (typically 100 km) along the entire cable length, with each span acting as an effective sensor. This division allows for a separation of signals from different parts of the cable, leading to higher S/N ratios on quiet deep-water segments and more easily interpreted waveforms. We show signals from several large earthquakes registered on 17 spans of the IRIS subsea telecommunications cable, that connects Iceland and Ireland. Multiple seismic body-wave phases, as well as longer period surface waves, can be tracked across the spans, or the array of effective sensors. Comparing the observed phase arrivals to those predicted by travel-time curves, we show how different phases are visible on different segments as expected by the varying orientation of individual segments relative to the seismic wave field. Furthermore, we simulate the observed waveforms using a spectral-element wave propagation software (SPECFEM3D_GLOBE), following the theoretical development of Fichtner et al 2022, and compare to the observed waveforms.
- Open Access
- 15 March 2025
- Published by Copernicus GmbH
Simulations of seismic waveforms observed on the IRIS subsea cable, connecting Iceland and Ireland
This study investigates the use of subsea communication cables as seismic monitoring instruments. We simulate the waveforms observed on 17 spans of the Iceland-Ireland subsea telecommunications cable, following the framework presented in Fichtner et al., 2022. We use an open source spectral-element wave propagation code (SPECFEM3D GLOBE) to simulate strain rate at a dense set of points along the cable. The simulations incorporate realistic physical conditions, including the effects of topography, gravity, crustal structure, ocean load and cable geometry, and are executed on the Elja HPC platform, using 150 CPUs.A Python-based pipeline processes and visualizes simulated strain data, supporting comparisons with real-world observations. This pipeline lays a foundation for a software library for analysis of seismic subsea cable data.Preliminary results indicate alignment between simulations and observations, with ongoing refinements addressing discrepancies caused by environmental noise and measurement uncertainties. The ability to model the observed strain response on the fiber optic cable, enables the incorporation of this dataset into traditional seismological applications, expanding observational coverage and contributing to the understanding of seismic processes in areas not accessible to traditional seismic networks.
- 15 March 2025
- Published by Copernicus GmbH
Open AccessSimulations of seismic waveforms observed on the IRIS subsea cable, connecting Iceland and Ireland
This study investigates the use of subsea communication cables as seismic monitoring instruments. We simulate the waveforms observed on 17 spans of the Iceland-Ireland subsea telecommunications cable, following the framework presented in Fichtner et al., 2022. We use an open source spectral-element wave propagation code (SPECFEM3D GLOBE) to simulate strain rate at a dense set of points along the cable. The simulations incorporate realistic physical conditions, including the effects of topography, gravity, crustal structure, ocean load and cable geometry, and are executed on the Elja HPC platform, using 150 CPUs.A Python-based pipeline processes and visualizes simulated strain data, supporting comparisons with real-world observations. This pipeline lays a foundation for a software library for analysis of seismic subsea cable data.Preliminary results indicate alignment between simulations and observations, with ongoing refinements addressing discrepancies caused by environmental noise and measurement uncertainties. The ability to model the observed strain response on the fiber optic cable, enables the incorporation of this dataset into traditional seismological applications, expanding observational coverage and contributing to the understanding of seismic processes in areas not accessible to traditional seismic networks.
- 25 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (13) , 6238-6249
Beyond 800 Gb/s Transmission Demonstration Using Carrierless Phase Retrieval Reception
We experimentally demonstrate a carrierless and local oscillator (LO)-free transmission over 100-km single-mode fiber (SMF) with 100-GBaud dual-polarization (DP) probabilistically shaped (PS)-64QAM at 5.6-bit/symbol entropy via a 100-GHz phase retrieval (PR) receiver, achieving a net rate of 835 Gb/s and an 8.27-b/s/Hz net optical spectral efficiency (OSE). Additionally, we also demonstrate 50-GBaud DP PS-256QAM transmission with 7.2 bits/symbol entropy over 40 km of standard SMF, achieving a net bit rate of 533 Gb/s and a net OSE of 10.55 b/s/Hz. In the discussion, a comparison with other reported transmission experiments utilizing direct detection (DD) and complex-field reconstruction techniques highlights the carrierless PR scheme's advantages in optical signal-to-noise-ratio (OSNR)-constrained links, particularly by conserving optical power typically allocated for carrier transmission. The carrierless PR reception demonstrates direct compatibility with coherent modulation formats and transmitters without sacrificing the effective OSNR, and it may offer a direct detection-based, wavelength-independent, LO-free, and coherent-compatible solution for future data center and metropolitan network interconnections.
- 25 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (13) , 6238-6249
Beyond 800 Gb/s Transmission Demonstration Using Carrierless Phase Retrieval Reception
We experimentally demonstrate a carrierless and local oscillator (LO)-free transmission over 100-km single-mode fiber (SMF) with 100-GBaud dual-polarization (DP) probabilistically shaped (PS)-64QAM at 5.6-bit/symbol entropy via a 100-GHz phase retrieval (PR) receiver, achieving a net rate of 835 Gb/s and an 8.27-b/s/Hz net optical spectral efficiency (OSE). Additionally, we also demonstrate 50-GBaud DP PS-256QAM transmission with 7.2 bits/symbol entropy over 40 km of standard SMF, achieving a net bit rate of 533 Gb/s and a net OSE of 10.55 b/s/Hz. In the discussion, a comparison with other reported transmission experiments utilizing direct detection (DD) and complex-field reconstruction techniques highlights the carrierless PR scheme's advantages in optical signal-to-noise-ratio (OSNR)-constrained links, particularly by conserving optical power typically allocated for carrier transmission. The carrierless PR reception demonstrates direct compatibility with coherent modulation formats and transmitters without sacrificing the effective OSNR, and it may offer a direct detection-based, wavelength-independent, LO-free, and coherent-compatible solution for future data center and metropolitan network interconnections.
- Top Cited Papers
- 18 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (23) , 10371-10379
High Data-Rate OESCLU-Band Transmission
We combine 6 doped-fiber amplifiers (O-(x2), E-, S-, C-, L-bands) with discrete Raman U-band amplifiers and distributed Raman-amplification to transmit in each of the low-loss transmission bands of a standard optical fiber. For transmission distances up to 100 km, we explore ultra-wideband transmission of up to 1505 × 25 GHz spaced channels covering the O-, E-, S-, C-, L- and U-bands from 1281.2 nm to 1649.9 nm. After describing the amplifier and spectrum flattening technology, we first characterize the transceiver in back-to-back configuration. Then, for 50 km transmission, we report a record aggregate transmission bandwidth of 37.6 THz with a record standard single-mode fiber transmission data-rate of 402.2 Tb/s, estimated from GMI, and 378.9 Tb/s after FEC decoding. 100 km transmission allows a 36.6 THz bandwidth with 339 Tb/s GMI estimated data-rate and 322.8 Tb/s decoded data-rate. These results show the potential of ultra-wideband transmission covering the low-loss window of silica fibers as well as the challenges of building such systems on longer fiber spans.
- 18 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (23) , 10371-10379
Top Cited PapersHigh Data-Rate OESCLU-Band Transmission
We combine 6 doped-fiber amplifiers (O-(x2), E-, S-, C-, L-bands) with discrete Raman U-band amplifiers and distributed Raman-amplification to transmit in each of the low-loss transmission bands of a standard optical fiber. For transmission distances up to 100 km, we explore ultra-wideband transmission of up to 1505 × 25 GHz spaced channels covering the O-, E-, S-, C-, L- and U-bands from 1281.2 nm to 1649.9 nm. After describing the amplifier and spectrum flattening technology, we first characterize the transceiver in back-to-back configuration. Then, for 50 km transmission, we report a record aggregate transmission bandwidth of 37.6 THz with a record standard single-mode fiber transmission data-rate of 402.2 Tb/s, estimated from GMI, and 378.9 Tb/s after FEC decoding. 100 km transmission allows a 36.6 THz bandwidth with 339 Tb/s GMI estimated data-rate and 322.8 Tb/s decoded data-rate. These results show the potential of ultra-wideband transmission covering the low-loss window of silica fibers as well as the challenges of building such systems on longer fiber spans.
- 13 May 2024
- Published by Optica Publishing Group in Journal of Optical Communications and Networking
- Vol. 16 (6) , 624-630
Automated fiber switch with path verification enabled by an AI-powered multi-task mobile robot
As the capacity of optical transport networks undergoes significant growth, there is an ongoing discussion on how to effectively leverage both spectral and spatial degrees of freedom to scale future network capacity. This paper presents an artificial intelligence (AI)-powered multi-task robot comprising a collaborative robotic arm and a mobile robotic base designed for optical network automation. The robot demonstrates the capability of direct fiber switching, establishing static fiber links that consume zero power and have minimal insertion loss from fiber connectors. As a precautionary measure before physically switching fiber cables, the robot performs path verification by detecting robot-driven events using real-time coherent receivers, aiming to avoid accidental unplugging. Additionally, the robot showcases its mobility by efficiently navigating between different network racks and rooms while executing various tasks. Implementing the automation of network operations using robots has the potential to reduce both capital and operational expenditures.
- 13 May 2024
- Published by Optica Publishing Group in Journal of Optical Communications and Networking
- Vol. 16 (6) , 624-630
Automated fiber switch with path verification enabled by an AI-powered multi-task mobile robot
As the capacity of optical transport networks undergoes significant growth, there is an ongoing discussion on how to effectively leverage both spectral and spatial degrees of freedom to scale future network capacity. This paper presents an artificial intelligence (AI)-powered multi-task robot comprising a collaborative robotic arm and a mobile robotic base designed for optical network automation. The robot demonstrates the capability of direct fiber switching, establishing static fiber links that consume zero power and have minimal insertion loss from fiber connectors. As a precautionary measure before physically switching fiber cables, the robot performs path verification by detecting robot-driven events using real-time coherent receivers, aiming to avoid accidental unplugging. Additionally, the robot showcases its mobility by efficiently navigating between different network racks and rooms while executing various tasks. Implementing the automation of network operations using robots has the potential to reduce both capital and operational expenditures.
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (11) , 4006-4012
321 Tb/s E/S/C/L-Band Transmission With E-Band Bismuth-Doped Fiber Amplifier and Optical Processor
Using a newly developed bismuth doped fiber amplifier operating across the E-band and a multi-port optical processor, we investigate wideband E/S/C/L-band transmission with signal bandwidths up to 27.8 THz and distances up to 200 km. Dense wavelength-division multiplexed (D-WDM) transmission is enabled by using a combination of thulium, erbium and bismuth doped-fiber amplifiers in combination with distributed Raman amplification. For 50 km transmission, we transmit a wideband DWDM signal comprising 1097 channels covering 212.3 nm (27.8 THz) from 1410.8 nm to 1623.1 nm for a record single-mode fiber (SMF) data-rate of 321 Tb/s (301 Tb/s after decoding), an increase of 25% on the previous record data-rate. We further show single span transmission at 100 km and 150 km before recording 270.9 Tb/s (258.1 Tb/s after decoding) for 200 km transmission over 2 amplified spans. These results show the potential of E-band transmission, to increase the information carrying capability of optical fibers and open the door to multi-band fiber networks built on already deployed fibers.
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (11) , 4006-4012
321 Tb/s E/S/C/L-Band Transmission With E-Band Bismuth-Doped Fiber Amplifier and Optical Processor
Using a newly developed bismuth doped fiber amplifier operating across the E-band and a multi-port optical processor, we investigate wideband E/S/C/L-band transmission with signal bandwidths up to 27.8 THz and distances up to 200 km. Dense wavelength-division multiplexed (D-WDM) transmission is enabled by using a combination of thulium, erbium and bismuth doped-fiber amplifiers in combination with distributed Raman amplification. For 50 km transmission, we transmit a wideband DWDM signal comprising 1097 channels covering 212.3 nm (27.8 THz) from 1410.8 nm to 1623.1 nm for a record single-mode fiber (SMF) data-rate of 321 Tb/s (301 Tb/s after decoding), an increase of 25% on the previous record data-rate. We further show single span transmission at 100 km and 150 km before recording 270.9 Tb/s (258.1 Tb/s after decoding) for 200 km transmission over 2 amplified spans. These results show the potential of E-band transmission, to increase the information carrying capability of optical fibers and open the door to multi-band fiber networks built on already deployed fibers.
- 5 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (13) , 4372-4385
Distortion-Aware Phase Retrieval Receiver for Carrierless High-Order QAM Transmission
We experimentally investigate transmitting high-order quadrature amplitude modulation (QAM) signals with carrierless and intensity-only measurements with phase retrieval (PR) receiving techniques. The intensity errors during measurement, including noise and distortions, are found to be a limiting factor for the precise convergence of the PR algorithm. To improve the PR reconstruction accuracy, we propose a distortion-aware PR scheme comprising both training and reconstruction stages. By estimating and emulating the distortion caused by various channel impairments, the proposed scheme enables enhanced agreement between the estimated and measured amplitudes throughout the PR iteration, thus resulting in improved reconstruction performance to support high-order QAM transmission. With the aid of the proposed techniques, we experimentally demonstrate 50-GBaud 16QAM and 32QAM signals transmitting through a standard single-mode optical fiber (SSMF) span of 40 and 80 km, and achieve bit error rates (BERs) below the 6.25% hard decision (HD)-forward error correction (FEC) and 25% soft decision (SD)-FEC thresholds for the two modulation formats, respectively.By tuning the pilot symbol ratio and applying concatenated coding, we also demonstrate that a post-FEC data rate of up to 140 Gb/s can be achieved for both distances at an optimal pilot symbol ratio of 20%.
- 5 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (13) , 4372-4385
Distortion-Aware Phase Retrieval Receiver for Carrierless High-Order QAM Transmission
We experimentally investigate transmitting high-order quadrature amplitude modulation (QAM) signals with carrierless and intensity-only measurements with phase retrieval (PR) receiving techniques. The intensity errors during measurement, including noise and distortions, are found to be a limiting factor for the precise convergence of the PR algorithm. To improve the PR reconstruction accuracy, we propose a distortion-aware PR scheme comprising both training and reconstruction stages. By estimating and emulating the distortion caused by various channel impairments, the proposed scheme enables enhanced agreement between the estimated and measured amplitudes throughout the PR iteration, thus resulting in improved reconstruction performance to support high-order QAM transmission. With the aid of the proposed techniques, we experimentally demonstrate 50-GBaud 16QAM and 32QAM signals transmitting through a standard single-mode optical fiber (SSMF) span of 40 and 80 km, and achieve bit error rates (BERs) below the 6.25% hard decision (HD)-forward error correction (FEC) and 25% soft decision (SD)-FEC thresholds for the two modulation formats, respectively.By tuning the pilot symbol ratio and applying concatenated coding, we also demonstrate that a post-FEC data rate of up to 140 Gb/s can be achieved for both distances at an optimal pilot symbol ratio of 20%.
- 1 January 2024
- Published by Optica Publishing Group
- p. SF1L.1
Transmission in a Field-Deployed Multimode Fiber Cable
In this invited paper, we review our recent results for mode-division-multiplexed transmission over subsets of spatial modes in a field-deployed 15-mode fiber cable, and analysis of impulse responses from individual fiber strands in the cable.
- 1 January 2024
- Published by Optica Publishing Group
- p. SF1L.1
Transmission in a Field-Deployed Multimode Fiber Cable
In this invited paper, we review our recent results for mode-division-multiplexed transmission over subsets of spatial modes in a field-deployed 15-mode fiber cable, and analysis of impulse responses from individual fiber strands in the cable.
- 1 January 2024
- Published by Optica Publishing Group
- p. M2A.4
Broadband Characterization of Randomly Coupled 19-Core Multicore Fiber
We evaluate 19-core randomly-coupled multi-core fiber using swept wavelength interferometry in the O-, E-, C- and L-bands. We show a differential mode delay reduction when unspooling the fiber and increased full-mixing length at shorter wavelengths.
- 1 January 2024
- Published by Optica Publishing Group
- p. M2A.4
Broadband Characterization of Randomly Coupled 19-Core Multicore Fiber
We evaluate 19-core randomly-coupled multi-core fiber using swept wavelength interferometry in the O-, E-, C- and L-bands. We show a differential mode delay reduction when unspooling the fiber and increased full-mixing length at shorter wavelengths.