LMLin Mei

Lin Mei

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lin Mei has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Multimodal Feature Sensing and Fusion Neural Network for Damage Localization by Ultrasonic Guided Waves

    by Lin Zhang, Lin Mei, Yuxin Bai, Yu Zeng, Zhiqiang Duan, Sida Chen, Qingying Li, Jing Peng, Shuaiyong Li

    Damage localization based on ultrasonic guided waves (UGWs) ensures the reliability and safety of composites. Efficient and accurate damage localization requires full integration of different modality features. However, existing deep learning-based damage localization methods usually focus on single-modal features and cannot deeply mine and fuse different features. In this paper, we propose a novel Multimodal Feature Sensing and Fusion Neural Network (MSFN) for damage localization by UGWs in composites. This method uses an innovative multimodal input mode, in which three different modal signals, namely, the damage signal, scattered wave signal, and energy density signal, are fed into the network as inputs. We use Convolutional Neural Networks (CNNs), Gated Recurrent Units (GRUs) and Bidirectional Gated Recurrent Units (BiGRUs) to construct specific encoders for the characteristics of the three signals to extract the features of different modalities efficiently and quickly. Then we employ an attention mechanism-guided feature fusion strategy to aggregate the various features, map out the correlation between the damage zones and the signal features, and finally decode them through successive linear layers to output the final damage localization results. Subsequent experimental results show that the damage localization accuracy of the MSFN can reach 98.13% even under noise interference. It is shown that its robustness and accuracy are much better than those of other existing networks and it has better localization speed and generalization. The proposed MSFN architecture comprises a CNN-based DS-encoder, a GRU-based SW-encoder, and a BiGRU-based ES-encoder, followed by an attention-guided fusion module, demonstrating its feasibility for near-real-time SHM applications.

  • Open Access

    Study on the Effect of Secondary Air Layout on CO Reduction Performance in a 75 t/h Biomass CFB Boiler Burning Wheat Straw

    by Jun Zhang, Yanmin Li, Lin Mei, Xiaoliang Yu, Xun Lv, Jinping Wang, Jin Yan, Rongyue Sun

    Biomass fuels play an important role in the field of fluidized bed combustion, but due to the diversity and uncertainty of fuels, there are usually some problems of high CO emission that cannot be directly solved by combustion adjustment. In this paper, a 75 t/h biomass fluidized bed was taken as the research object. It was observed from the field test that the gas incomplete combustion loss reached 12.13% when mono-combustion of wheat straw was conducted, and the CO concentration in the exhaust gas exceeded 30k ppm. Combined with the CPFD numerical simulation, the combustion characteristics and influence of secondary air layout on CO reduction performance were discussed in detail. The results revealed that the gas temperature gradually increased along furnace height under the initial condition, and the maximum temperature was more than 1000 °C at furnace outlet. The air curtain of the secondary air jets was insufficient, and the wheat straw rose rapidly as it entered into the furnace. By arranging adjacent secondary air ports above each fuel-feeding inlet, the residence time of particles in the furnace could be significantly increased, thus, the furnace temperature distribution was more reasonable and the CO emission was reduced by 58.6%.


  • Open Access

    An Experimental Study on SO2 Emission and Ash Deposition Characteristics of High Alkali Red Mud under Large Proportional Co-Combustion Conditions in Fluidized Bed

    by Xiaoliang Yu, Jin Yan, Rongyue Sun, Lin Mei, Yanmin Li, Shuyuan Wang, Fan Wang, Yicheng Gu

    As an industrial solid waste, the discharge of a large amount of red mud (RM) causes serious environmental problems; thus, a large proportion of RM co-combustion has been proposed to solve the consumption problem. In this paper, an experiment with various proportions of RM co-combustion was conducted on a 0.2 t/h circulating fluidized bed (CFB) boiler. Desulfurization performance, combustion characteristics, and ash deposition characteristics were analyzed, especially under the large proportional co-combustion conditions. As the study results showed, the desulfurization efficiency was positively correlated with the RM co-combustion proportion. When the RM co-combustion proportion reached 50%, the desulfurization efficiency was over 94%. After a period of cyclic combustion, the highest desulfurization efficiency exceeded 99.5%. The smaller size of RM was beneficial to improve the combustion efficiency and the combustion stability. However, a large area of sintering formed on the top of the heating surface in the furnace, which was lighter than the sintering of high alkali fuels such as Zhundong coal. Meanwhile, the content of sulfates, such as Na2SO4 and CaSO4, in the ash increased, which clearly proves that RM has the desulfurization effect. Therefore, a large proportion of co-combustion could meet the requirements of in-situ desulfurization and realize the resource utilization of RM.