Marjorie Cavarroc
Research Subjects
Marjorie Cavarroc has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Pascal Brault
Groupe de Recherches sur l'Energetique des Milieux Ionises
3 shared publications - Anne-Lise Thomann
GREMI, CNRS, Université d’Orléans, 14 rue d’Issoudun, 45067 Orléans Cedex 2, France
2 shared publications - Edern Menou
Safran Tech 4 , rue des jeunes bois, Châteaufort, CS 80112, F-78772 Magny-les-Hameaux
2 shared publications Nicolas Froloff
2 shared publications- Adèle Girardeau
Laboratory on Plasma and Conversion of Energy (LAPLACE), University of Toulouse, 31062 Toulouse, France
1 shared publication Amaël Caillard
1 shared publication
Latest Publications
- Open Access
- 22 September 2026
- Published by Elsevier in SSRN Electronic Journal
Enhanced Understanding of Material Removal Mechanisms during Solid Particle Erosion of Ti-6Al-4V
Solid particle erosion (SPE) is a tribological process that reduces the operational lifetime of aerospace components and power generation turbines. This study investigates the microstructural response and material removal mechanisms of the α-β titanium alloy Ti-6Al-4V under SPE. Testing was performed at 75 m/s across impingement angles of 15–90° using two erodents: 50 µm Al2O3 and 140 µm crushed glass. Mechanistic investigations focused on normal incidence (90°) erosion by Al2O3, including single particle impacts, with complementary analyses of crushed glass at 90°, and peak-erosion angles for each erodent. Subsurface damage is highly localized–Plasma Focused Ion Beam cross-sections revealed erosion-affected depths of 5–9 µm, matched by nanoindentation mapping which showed a 12% hardness increase within this region. Transmission electron microscopy and selected area electron diffraction revealed dynamic recrystallization (DRX) of α grains near impact sites, producing randomly oriented 10–40 nm nanocrystals within a disordered matrix, while β grains were plastically deformed rather than recrystallized. {10-12} and {11-21} deformation twins extended beyond the DRX zone into deeper subsurface grains. Single impacts and steady-state erosion showed excellent agreement in penetration depth, erosion-affected depth, and microstructural changes. These results indicate that SPE at 90° is governed by repeated interactions with a damaged, particle-saturated surface. A material removal sequence is proposed in which each impact regenerates a self-limiting recrystallized layer above a twinned, work-hardened sublayer, and material detaches from the recrystallized layer itself. The resulting erosion-affected zone is shallow, hardened, and continuously renewed, rather than showing deep cumulative damage or thermal softening.
- 22 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhanced Understanding of Material Removal Mechanisms during Solid Particle Erosion of Ti-6Al-4V
Solid particle erosion (SPE) is a tribological process that reduces the operational lifetime of aerospace components and power generation turbines. This study investigates the microstructural response and material removal mechanisms of the α-β titanium alloy Ti-6Al-4V under SPE. Testing was performed at 75 m/s across impingement angles of 15–90° using two erodents: 50 µm Al2O3 and 140 µm crushed glass. Mechanistic investigations focused on normal incidence (90°) erosion by Al2O3, including single particle impacts, with complementary analyses of crushed glass at 90°, and peak-erosion angles for each erodent. Subsurface damage is highly localized–Plasma Focused Ion Beam cross-sections revealed erosion-affected depths of 5–9 µm, matched by nanoindentation mapping which showed a 12% hardness increase within this region. Transmission electron microscopy and selected area electron diffraction revealed dynamic recrystallization (DRX) of α grains near impact sites, producing randomly oriented 10–40 nm nanocrystals within a disordered matrix, while β grains were plastically deformed rather than recrystallized. {10-12} and {11-21} deformation twins extended beyond the DRX zone into deeper subsurface grains. Single impacts and steady-state erosion showed excellent agreement in penetration depth, erosion-affected depth, and microstructural changes. These results indicate that SPE at 90° is governed by repeated interactions with a damaged, particle-saturated surface. A material removal sequence is proposed in which each impact regenerates a self-limiting recrystallized layer above a twinned, work-hardened sublayer, and material detaches from the recrystallized layer itself. The resulting erosion-affected zone is shallow, hardened, and continuously renewed, rather than showing deep cumulative damage or thermal softening.
- Open Access
- 17 March 2026
- Published by MDPI AG in Nanomaterials
- Vol. 16 (6) , 364
Organometallic Synthesis of Platinum-Based Nanomaterials for the Oxygen Reduction Reaction
Pt-based catalysts remain the most effective materials for the oxygen reduction reaction (ORR) at the cathode of proton exchange membrane fuel cells (PEMFCs); however, platinum scarcity and high cost severely limit the large-scale deployment of the technology. Improving catalytic activity and durability through precise control of nanoparticle morphology is therefore crucial for reducing costs and enhancing sustainability, enabling PEMFC widespread adoption. In this context, carbon-supported Pt-based nanoparticles with a 30 wt.% Pt loading were synthesized by an organometallic chemistry approach using hexadecylamine (HDA) as a stabilizer, allowing fine control over nanoparticle morphology. Two distinct synthesis pathways (one-pot and two-step procedures) were used to prepare platinum catalysts supported on KetjenBlack EC-300J (KB), and their influence on the electrocatalytic activity of the obtained nanomaterials was studied. Furthermore, the effect of HDA stabilization on catalyst performance was investigated. Directly synthesized Pt/KB catalysts exhibited similar ORR mass activity, regardless of whether or not HDA was present. Pt/KB prepared by the two-step procedure showed a significantly lower performance. Additionally, despite a larger loss of electrochemical surface area during an accelerated stress test compared to a commercial Pt/C reference, PtHDA/KB and Pt/KB catalysts maintained stable mass activity and limited specific activity degradation, highlighting the beneficial effect of nanoparticle stabilization in the presence of HDA on prolonged electrocatalyst cycling.
- 17 March 2026
- Published by MDPI AG in Nanomaterials
- Vol. 16 (6) , 364
Open AccessOrganometallic Synthesis of Platinum-Based Nanomaterials for the Oxygen Reduction Reaction
Pt-based catalysts remain the most effective materials for the oxygen reduction reaction (ORR) at the cathode of proton exchange membrane fuel cells (PEMFCs); however, platinum scarcity and high cost severely limit the large-scale deployment of the technology. Improving catalytic activity and durability through precise control of nanoparticle morphology is therefore crucial for reducing costs and enhancing sustainability, enabling PEMFC widespread adoption. In this context, carbon-supported Pt-based nanoparticles with a 30 wt.% Pt loading were synthesized by an organometallic chemistry approach using hexadecylamine (HDA) as a stabilizer, allowing fine control over nanoparticle morphology. Two distinct synthesis pathways (one-pot and two-step procedures) were used to prepare platinum catalysts supported on KetjenBlack EC-300J (KB), and their influence on the electrocatalytic activity of the obtained nanomaterials was studied. Furthermore, the effect of HDA stabilization on catalyst performance was investigated. Directly synthesized Pt/KB catalysts exhibited similar ORR mass activity, regardless of whether or not HDA was present. Pt/KB prepared by the two-step procedure showed a significantly lower performance. Additionally, despite a larger loss of electrochemical surface area during an accelerated stress test compared to a commercial Pt/C reference, PtHDA/KB and Pt/KB catalysts maintained stable mass activity and limited specific activity degradation, highlighting the beneficial effect of nanoparticle stabilization in the presence of HDA on prolonged electrocatalyst cycling.
- 22 September 2025
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 717
Exploring oxygen dissociation on hexagonal boron nitride: Insight from high-temperature molecular dynamics simulation
- 22 September 2025
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 717
Exploring oxygen dissociation on hexagonal boron nitride: Insight from high-temperature molecular dynamics simulation
- Open Access
- 20 May 2025
- Published by IOP Publishing in Journal of Physics: Materials
- Vol. 8 (3) , 035002
Melanin granules extracted from Sepia ink: a nanoscale study of charge carrier transport
Eumelanin, the brown-black member of the melanin family of biopigments, has emerged as a promising material for sustainable organic electronics. Sepia eumelanin develops hierarchically from (5, 6)-dihydroxyindole (DHI) and (5, 6)-dihydroxyindole-2-carboxylic acid (DHICA) monomers, and its structure is made up of granules with typical size in the 100–300 nm range. Literature reports that Sepia eumelanin (from now on indicated as Sepia melanin), derived from the ink sac of cuttlefish, exhibits predominant electronic transport in dry state and mixed ionic–electronic transport in its hydrated state when studied at millimetric or micrometric distance ranges. To explore the upper limit of the conductivity of Sepia melanin and unlock its full technological potential, we investigated its electrical response at the nanoscale where the influence of granule boundaries is expected to be minimal. Using electrodes patterned at the nanoscale by e-beam lithography, we run current–voltage, current–time and electrochemical impedance spectroscopy measurements; we observed predominant electronic transport mechanisms in Sepia melanin, with conductivities that increase as the interelectrode distance decreases. Temperature-resolved experiments permitted us to deduce the transport activation energy. Our work highlights the importance of exploring the electrical response of natural materials across varying distance scales to exploit their full potential for sustainable organic electronics.
- 20 May 2025
- Published by IOP Publishing in Journal of Physics: Materials
- Vol. 8 (3) , 035002
Open AccessMelanin granules extracted from Sepia ink: a nanoscale study of charge carrier transport
Eumelanin, the brown-black member of the melanin family of biopigments, has emerged as a promising material for sustainable organic electronics. Sepia eumelanin develops hierarchically from (5, 6)-dihydroxyindole (DHI) and (5, 6)-dihydroxyindole-2-carboxylic acid (DHICA) monomers, and its structure is made up of granules with typical size in the 100–300 nm range. Literature reports that Sepia eumelanin (from now on indicated as Sepia melanin), derived from the ink sac of cuttlefish, exhibits predominant electronic transport in dry state and mixed ionic–electronic transport in its hydrated state when studied at millimetric or micrometric distance ranges. To explore the upper limit of the conductivity of Sepia melanin and unlock its full technological potential, we investigated its electrical response at the nanoscale where the influence of granule boundaries is expected to be minimal. Using electrodes patterned at the nanoscale by e-beam lithography, we run current–voltage, current–time and electrochemical impedance spectroscopy measurements; we observed predominant electronic transport mechanisms in Sepia melanin, with conductivities that increase as the interelectrode distance decreases. Temperature-resolved experiments permitted us to deduce the transport activation energy. Our work highlights the importance of exploring the electrical response of natural materials across varying distance scales to exploit their full potential for sustainable organic electronics.
- Open Access
- 6 May 2025
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 100
Conventional and high power impulse magnetron sputtering deposition of tantalum nitride films: a molecular dynamics approach
For understanding and controlling film growth parameters of various sputtering deposition conditions, molecular dynamics simulations are carried out to describe Tantalum Nitride conventional Magnetron Sputtering and High Power Impulse Magnetron Sputtering (HiPIMS) film growth and structure. It includes full atomic and ion energy distribution for a realistic account of experimental conditions, notably for HiPIMS deposition technique. Results are well compared with available experimental results in the literature, demonstrating that the present method is well suited for a very broad set of experimental conditions. The effect of the sputtered ion to neutral ratio on the film crystallographic structure is addressed using simulated X-ray diffraction and polyhedral template matching methods. It is shown that hcp phase predominates at moderate ion flux, and always coexists with fcc phase. The present molecular dynamics simulations, are therefore a powerful tool for correlating the predicted thin film structure to experimental conditions.
- 6 May 2025
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 100
Open AccessConventional and high power impulse magnetron sputtering deposition of tantalum nitride films: a molecular dynamics approach
For understanding and controlling film growth parameters of various sputtering deposition conditions, molecular dynamics simulations are carried out to describe Tantalum Nitride conventional Magnetron Sputtering and High Power Impulse Magnetron Sputtering (HiPIMS) film growth and structure. It includes full atomic and ion energy distribution for a realistic account of experimental conditions, notably for HiPIMS deposition technique. Results are well compared with available experimental results in the literature, demonstrating that the present method is well suited for a very broad set of experimental conditions. The effect of the sputtered ion to neutral ratio on the film crystallographic structure is addressed using simulated X-ray diffraction and polyhedral template matching methods. It is shown that hcp phase predominates at moderate ion flux, and always coexists with fcc phase. The present molecular dynamics simulations, are therefore a powerful tool for correlating the predicted thin film structure to experimental conditions.
- Open Access
- 8 April 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (14)
Phase formation prediction in magnetron sputtered Cu(Ti)Zn thin films: Numerical vs experimental approaches
In this work, we evaluated the ability of three numerical methods to predict the phase formation in Cu–Zn binary and Cu–Ti–Zn ternary alloy thin films deposited by DC-magnetron sputter deposition. Molecular dynamics (MD) simulations were carried out to simulate the growth of the alloy film and study the organization at the atomic level. A Machine Learning (ML) approach trained with a recently published bulk HEA (high-entropy alloy) database was used to determine the presence of an amorphous phase, solid solutions, or/and intermetallics. Finally, CALPHAD (CALculation of PHAse Diagrams) thermodynamic modeling allows one to simulate the phase diagrams. Crystalline phases formed in experimental films were investigated by grazing incidence x-ray diffraction (GIXRD). Comparison with CALPHAD results highlights that for pure Ti or binary Cu–Zn films, the thermodynamically stable phases are formed in the films. Less agreement was found at low or high percentage of Ti introduced in the Cu–Zn system, and drastic differences were observed for elemental compositions close to equimolarity. In those cases, the out of equilibrium nature of the magnetron sputtering deposition technique is evidenced. The very limited agreement between the GIXRD and ML approach is explained by the available database, which is exclusively based on bulk alloys. Elemental composition of the alloy does not itself determine the stabilized phases: elaboration techniques are to be taken into account too. MD simulations bring information on a possible segregation of the Zn element to the surface and grain boundaries. A very good agreement is evidenced between the calculated and experimental diffraction patterns.
- 8 April 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (14)
Open AccessPhase formation prediction in magnetron sputtered Cu(Ti)Zn thin films: Numerical vs experimental approaches
In this work, we evaluated the ability of three numerical methods to predict the phase formation in Cu–Zn binary and Cu–Ti–Zn ternary alloy thin films deposited by DC-magnetron sputter deposition. Molecular dynamics (MD) simulations were carried out to simulate the growth of the alloy film and study the organization at the atomic level. A Machine Learning (ML) approach trained with a recently published bulk HEA (high-entropy alloy) database was used to determine the presence of an amorphous phase, solid solutions, or/and intermetallics. Finally, CALPHAD (CALculation of PHAse Diagrams) thermodynamic modeling allows one to simulate the phase diagrams. Crystalline phases formed in experimental films were investigated by grazing incidence x-ray diffraction (GIXRD). Comparison with CALPHAD results highlights that for pure Ti or binary Cu–Zn films, the thermodynamically stable phases are formed in the films. Less agreement was found at low or high percentage of Ti introduced in the Cu–Zn system, and drastic differences were observed for elemental compositions close to equimolarity. In those cases, the out of equilibrium nature of the magnetron sputtering deposition technique is evidenced. The very limited agreement between the GIXRD and ML approach is explained by the available database, which is exclusively based on bulk alloys. Elemental composition of the alloy does not itself determine the stabilized phases: elaboration techniques are to be taken into account too. MD simulations bring information on a possible segregation of the Zn element to the surface and grain boundaries. A very good agreement is evidenced between the calculated and experimental diffraction patterns.
- Open Access
Numerical vs Experimental Sputtering Deposition Phase formation prediction in magnetron sputtered Cu(Ti)Zn thin films : Numerical vs Experimental approaches
Numerical vs Experimental Sputtering DepositionIn this work we evaluated the ability of three numerical methods to predict the phase formation in Cu-Zn binary and Cu-Ti-Zn ternary alloy thin films deposited by DC-magnetron sputter deposition. Molecular dynamics simulations were carried out to simulate the growth of the alloy film and study the organization at the atomic level. A Machine Learning (ML) approach trained with a recently published bulk HEA (high entropy alloy) database was used to determine the presence of an amorphous phase, solid solutions or/and intermetallics. Finally, CALPHAD (CALculation of PHAse Diagrams) thermodynamic modeling based on Gibbs energy calculations allows to simulate the phase diagrams. This was done taking the experimental energy distribution functions of film forming species as inputs for the calculations. In this paper we discuss both agreements and limits of each method depending on their starting hypotheses and expected domains of validity. Crystalline phases formed in experimental films were investigated by grazing incidence X-ray diffraction (GIXRD). Comparison with CALPHAD results highlight that for pure Ti or binary Cu-Zn films, the thermodynamically stable phases are formed in the films. Less agreement was found at low or high percentage of Ti introduced in the Cu-Zn system, and drastic differences were observed for compositions close to equimolarity. In those cases, the out of equilibrium nature of the magnetron sputtering deposition technique is evidenced. The very limited agreement between GIXRD and ML approach is explained by the available database which is exclusively based on bulk alloys. Chemical composition of the alloy does not itself determine the stabilized phases: elaboration techniques are to be taken into account too. Molecular Dynamics (MD) simulations bring information on a possible segregation of the Zn element to the surface and grain boundaries. An interesting result is the very good agreement evidenced between the diffraction patterns calculated on the simulated films and that experimentally measured GIXRD
Open AccessNumerical vs Experimental Sputtering Deposition Phase formation prediction in magnetron sputtered Cu(Ti)Zn thin films : Numerical vs Experimental approaches
Numerical vs Experimental Sputtering DepositionIn this work we evaluated the ability of three numerical methods to predict the phase formation in Cu-Zn binary and Cu-Ti-Zn ternary alloy thin films deposited by DC-magnetron sputter deposition. Molecular dynamics simulations were carried out to simulate the growth of the alloy film and study the organization at the atomic level. A Machine Learning (ML) approach trained with a recently published bulk HEA (high entropy alloy) database was used to determine the presence of an amorphous phase, solid solutions or/and intermetallics. Finally, CALPHAD (CALculation of PHAse Diagrams) thermodynamic modeling based on Gibbs energy calculations allows to simulate the phase diagrams. This was done taking the experimental energy distribution functions of film forming species as inputs for the calculations. In this paper we discuss both agreements and limits of each method depending on their starting hypotheses and expected domains of validity. Crystalline phases formed in experimental films were investigated by grazing incidence X-ray diffraction (GIXRD). Comparison with CALPHAD results highlight that for pure Ti or binary Cu-Zn films, the thermodynamically stable phases are formed in the films. Less agreement was found at low or high percentage of Ti introduced in the Cu-Zn system, and drastic differences were observed for compositions close to equimolarity. In those cases, the out of equilibrium nature of the magnetron sputtering deposition technique is evidenced. The very limited agreement between GIXRD and ML approach is explained by the available database which is exclusively based on bulk alloys. Chemical composition of the alloy does not itself determine the stabilized phases: elaboration techniques are to be taken into account too. Molecular Dynamics (MD) simulations bring information on a possible segregation of the Zn element to the surface and grain boundaries. An interesting result is the very good agreement evidenced between the diffraction patterns calculated on the simulated films and that experimentally measured GIXRD
- Open Access
Electrochemical Behavior of Tantalum Nitride Protective Layers for PEMFC Application
Proton Exchange Membrane Fuel Cells (PEMFCs) are promising technology to convert chemical energy from dihydrogen in electrical energy. HT-PEMFCs are working at high temperatures (above 120 °C) and with doped orthophosphoric acid H3PO4 PBI membranes. In such devices, bipolar metallic plates are used to provide reactive gas inside the fuel cell and collect the electrical current. The metallic elements used as bipolar plates, end plates, and interconnectors in acid electrolyte and gaseous fuel cells are severely damaged by a combination of oxidation (due in particular to the use of oxygen, whether pure or contained in the air) and corrosion (due in particular to acid effluents from the electrolyte). This degradation rapidly leads to the loss of the electrical conductivity of the metallic elements and today requires the use of very specific alloys, possibly coated with pure gold. The solution investigated in the present study is the use of a protective coating based on single-phase nitrides obtained by reactive magnetron sputtering or reactive HiPIMS (High-Power Impulse Magnetron Sputtering). The influence of the microstructure on the physical–chemical properties was studied. The electrochemical properties were quantified following two approaches. First, the corrosion current of the developed coatings was measured at room temperature and at higher temperatures using the Linear Sweep Voltammetry (LSV) technique. Then, Electrochemical Impedance Spectroscopy (EIS) measurements were performed to better identify and evaluate their corrosion-resistance performances.
Open AccessElectrochemical Behavior of Tantalum Nitride Protective Layers for PEMFC Application
Proton Exchange Membrane Fuel Cells (PEMFCs) are promising technology to convert chemical energy from dihydrogen in electrical energy. HT-PEMFCs are working at high temperatures (above 120 °C) and with doped orthophosphoric acid H3PO4 PBI membranes. In such devices, bipolar metallic plates are used to provide reactive gas inside the fuel cell and collect the electrical current. The metallic elements used as bipolar plates, end plates, and interconnectors in acid electrolyte and gaseous fuel cells are severely damaged by a combination of oxidation (due in particular to the use of oxygen, whether pure or contained in the air) and corrosion (due in particular to acid effluents from the electrolyte). This degradation rapidly leads to the loss of the electrical conductivity of the metallic elements and today requires the use of very specific alloys, possibly coated with pure gold. The solution investigated in the present study is the use of a protective coating based on single-phase nitrides obtained by reactive magnetron sputtering or reactive HiPIMS (High-Power Impulse Magnetron Sputtering). The influence of the microstructure on the physical–chemical properties was studied. The electrochemical properties were quantified following two approaches. First, the corrosion current of the developed coatings was measured at room temperature and at higher temperatures using the Linear Sweep Voltammetry (LSV) technique. Then, Electrochemical Impedance Spectroscopy (EIS) measurements were performed to better identify and evaluate their corrosion-resistance performances.
- Open Access
Direct Liquid Reactor-Injector of Nanoparticles: A Safer-by-Design Aerosol Injection for Nanocomposite Thin-Film Deposition Adapted to Various Plasma-Assisted Processes
The requirements of nanocomposite thin films, having non-aggregated nanoparticles homogeneously dispersed in the matrix, have been realized using a new method of Direct Liquid Reactor-Injector (DLRI) of nanoparticles. In this approach, unlike conventional aerosol-assisted plasma deposition, the nanoparticles are synthesized before their injection as an aerosol into plasma. In our experiments, we have used two different plasma reactors, namely an asymmetric low-pressure RF plasma reactor and a parallel plate dielectric barrier discharge at atmospheric pressure. Our results have shown that DLRI can be easily coupled with various plasma processes as this approach allows the deposition of high-quality multifunctional nanocomposite thin films, with embedded nanoparticles of less than 10 nm in diameter. Hence, DLRI coupled with plasma processes meets the specifications for the deposition of multifunctional coatings.
Open AccessDirect Liquid Reactor-Injector of Nanoparticles: A Safer-by-Design Aerosol Injection for Nanocomposite Thin-Film Deposition Adapted to Various Plasma-Assisted Processes
The requirements of nanocomposite thin films, having non-aggregated nanoparticles homogeneously dispersed in the matrix, have been realized using a new method of Direct Liquid Reactor-Injector (DLRI) of nanoparticles. In this approach, unlike conventional aerosol-assisted plasma deposition, the nanoparticles are synthesized before their injection as an aerosol into plasma. In our experiments, we have used two different plasma reactors, namely an asymmetric low-pressure RF plasma reactor and a parallel plate dielectric barrier discharge at atmospheric pressure. Our results have shown that DLRI can be easily coupled with various plasma processes as this approach allows the deposition of high-quality multifunctional nanocomposite thin films, with embedded nanoparticles of less than 10 nm in diameter. Hence, DLRI coupled with plasma processes meets the specifications for the deposition of multifunctional coatings.