LGLisa Guan

Lisa Guan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lisa Guan has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Identification of bioburden associated with nonmetallic spacecraft materials using culture-based and metagenomic analyses

    by Chelsi D. Cassilly, Lisa Guan, Michael D. Brandhagen, Nyssa K. Krull, Brian T. Murphy, Precious A. Mitchell

  • Open Access

    Biocidal Conditions in Low-Mars-Orbit Can Inactivate Bioburden on External Mars Spacecraft Surfaces and Dust Particles Within a Few Sols

    by Andrew C. Schuerger, Petra Schwendner, Lisa Guan, Jerami Mennella, Nicholas Heinz, Ioannis Mikellides, Brian G. Clement

    Mars Sample Return Program planning includes a series of spacecraft staged both on the Martian surface and in low-Mars-orbit (LMO). During the transfer of samples into orbit, external spacecraft surfaces might be exposed to Mars dust carried on the sample container exterior and possibly extant microbiota (if present). This study was designed to characterize the synergistic effects of LMO ultraviolet irradiation, vacuum, and solar heating on the survival of two UV-resistant and heat-tolerant bacteria, one yeast, and one fungus. The species tested were Bacillus pumilus SAFR-032 spores, Geobacillus stearothermophilus ATCC 12980 spores, Naganishia onofrii DBVPG 5303 cells, and Aspergillus fumigatus ISSFT-021-30 spores, respectively. Spores of A. fumigatus ISSFT-021-30 and B. pumilus were also exposed to LMO conditions with and without a Mojave Mars Simulant (MMS) dust layer. Based on the data, the time required to reach the desired Sterility Assurance Level (SAL; dose-defined to yield a −12 log reduction) was 2.0 h for A. fumigatus ISSFT-021-30 and 76.6 min for B. pumilus SAFR-032 if exposed directly to the solar UV beam under LMO conditions. With the MMS present, predicted times to reach one SAL were extended to 22 h and 1.72 h, respectively. Analysis of UV transmittance through cell stacks of up to 12 µm thick was performed for A. fumigatus ISSFT-021-30. Results indicated that ~4–5% of UVC photons can penetrate through 12 µm stacked aggregates of spores. These findings indicate that (1) the LMO environment can be used to attain the mandated levels of spacecraft surface bioburden reductions and (2) dust shielding and microbial aggregation attenuate UV irradiation, leading to extended orbital residence times to achieve mandated bioburden reductions.


  • Open Access

    Susceptibility of microbes to far-UVC light (222 nm) on spacecraft and cleanroom surfaces

    by Camryn Petersen, Joshua Urbano, Akemi Hinzer, Igor Shuryak, Eric Wang, Raabia Hashmi, Lisa Guan, Manuela Buonanno, David Welch

    Far-UVC light (222 nm) is an emerging decontamination tool with potential for spacecraft assembly applications due to its strong germicidal efficacy and minimal risk to human health. This study evaluated the susceptibility of three UV-resistant microbial species, Deinococcus radiodurans and Bacillus subtilis as vegetative cells and Bacillus pumilus as spores, across eight spacecraft and cleanroom-relevant materials with varying surface properties, including contact angle, reflectivity, and roughness. While D. radiodurans demonstrated the highest overall resistance to far-UVC, material properties significantly influenced its inactivation rate (k 1 [cm 2 /mJ]), and its susceptibility varied significantly by surface. No significant relationship between material properties influencing k 1 values was observed for B. subtilis and B. pumilus . Collectively, these findings highlight far-UVC as a robust and practical bioburden reduction tool capable of inactivating resistant microbes regardless of material surface characteristics. IMPORTANCE: This study builds upon previous research on the inactivation of hardy bacteria and spores using far-UVC light by evaluating the susceptibility of microbes to far-UVC light across a range of surface materials. By focusing on hardy organisms and diverse substrates, this work provides critical insights into the practical applications of far-UVC technology in complex environments. Microbial disinfection is a key component of planetary protection, ensuring that space exploration activities do not inadvertently transport terrestrial organisms to extraterrestrial environments. These findings demonstrate that far-UVC is effective across materials with varying properties and can serve as an effective alternative for bioburden reduction that can be safely operated in occupied spaces.


  • Open Access

    Susceptibility of extremophiles to far-UVC light for bioburden reduction in spacecraft assembly facilities

    by Camryn Petersen, Manuela Buonanno, Lisa Guan, Akemi Hinzer, Joshua Urbano, Raabia Hashmi, Igor Shuryak, Ceth Parker, David Welch


  • Open Access

    Modeling of recovery efficiency of sampling devices used in planetary protection bioburden estimation

    by Michael DiNicola, Arman Seuylemezian, Lisa Guan, Christine Moissl-Eichinger, Amy Baker, Jason Johns

    Planetary protection is a discipline dedicated to preventing biological contamination between celestial bodies and Earth during space exploration to ensure the integrity of scientific research. National space agencies such as the National Aeronautics and Space Administration and the European Space Agency set biological cleanliness requirements for their missions based on the guidelines provided in The Committee on Space Research’s Planetary Protection Policy. Compliance with these requirements is often demonstrated by surface sampling of spacecraft hardware and associated surfaces to enumerate the number of microorganisms present and establish that they are below the required level. The discipline has employed a variety of tools to perform sampling; the recovery efficiency of which is a key parameter used to generate spacecraft level cleanliness estimates. In this study, we investigated how recovery efficiency differs by inoculum amount and species. This was analyzed across different sampling devices using a set of microorganisms applied to stainless steel surfaces (representative of spacecraft surfaces) and two processing methods. Data were analyzed by developing a probabilistic model of the experimental process, from stainless steel coupon inoculation through recovery of spores observed in the form of colony forming units. The model quantifies the probability that an individual spore is recovered, a key metric for predicting bioburden and statistically assessing bioburden requirements. A cost function was developed to identify those assay methods that provided optimal bioburden estimation capability. Results show the nylon-flocked swab and the TX3211 wipe yield the highest recovery efficiency of those tested. IMPORTANCE: Planetary protection at the National Aeronautics and Space Administration (NASA) requires bioburden on certain spacecraft to be estimated via sampling in order to comply with biological cleanliness requirements. To achieve this, the recovery efficiency of devices used to sample the spacecraft pre-launch must be understood and their uncertainty quantified in order to produce the most reasonable estimates of bioburden. This study brings together experiments performed by NASA and the European Space Agency with approved swab and wipe sampling devices, inoculating steel coupons with laboratory strains of Bacillus spp. spores commonly recovered from spacecraft assembly clean rooms ( B. atrophaeus , B. megaterium , B. safensis and B. thuringiensis ), with a mathematical model of the assay process to assess recovery efficiency. The statistical treatment developed in this study allows comparison of bioburden estimates made from different devices processed by different methods. This study also gives stakeholders and practitioners a statistically rigorous approach to predict bioburden that can be folded into future modeling efforts.


  • Applied Approach for Assessing Bioburden of the Mars 2020 Parachute Assembly

    by Lisa Guan, Brian Clement, Moogega Cooper

    The Mars 2020 mission delivered the Perseverance rover to the surface of Mars using a supersonic parachute manufactured at Airborne Systems, California. The Mars 2020 spacecraft, including the flight parachute, was subject to Planetary Protection spore bioburden compliance. Many previous missions with similar parachutes applied manufacturing specifications for calculating bioburden. Although the Mars 2020 parachute was manufactured in an uncontrolled environment, preliminary sampling of a flight-like parachute manufactured in the same facility suggested that the actual spore bioburden levels were potentially orders of magnitude lower than specification values for uncontrolled manufacturing (100,000 spores/m 2 ). Several experiments were designed and carried out throughout the project timeline in an effort to estimate a representative bioburden for the flight parachute. Tests were performed on various parachute materials, including direct sampling and destructive assays of proxy materials. Different bioburden densities were applied to large continuous areas of the canopy, which experienced minimal handling, and seamed areas of the parachute that were likely to experience more handling during the stitching process. In addition, an approach to account for various thermal zones was developed and applied toward calculating log reduction for the parachute assembly. These various methods that were used toward different areas and materials of the Mars 2020 flight parachute provided a nuanced and data-backed estimate of spore bioburden density that can be adopted by future missions.

  • Draft Genome Sequences of Spacecraft-Associated Microbes Isolated from Six NASA Missions

    by Michelle T. Tran, Arman Seuylemezian, Alonna Wright, David Coil, Jonathan Eisen, Lisa Guan

    Whole-genome sequencing can be used to better understand and assess the functional abilities of microorganisms isolated from spacecraft hardware and associated surfaces for planetary protection (PP) purposes. We sequenced 191 isolates from 6 spaceflight missions with PP requirements and identified them using Illumina-based sequencing methods and matrix-assisted laser desorption ionization–time of flight (MALDI-TOF) mass spectrometry.


  • Open Access

    Establishing Sterility Assurance for Bacillus canaveralius 29669 Spores Under High Heat Exposure

    by Zachary Steven Dean, Michael DiNicola, Emily Klonicki, Scott Roberts, Brian Gregory Clement, Lisa Guan

    The ever-increasing complexity in critical spacecraft hardware and materials has led to the development of new microbial reduction procedures as well as to changes in established processes such as heat microbial reduction (HMR). In the space biology field of Planetary Protection, 500°C for 0.5 s is the current HMR recommendation to reduce microorganisms from flight hardware. However, more studies are needed to effectively determine the microbial reduction capability of high-temperature (more than 200°C), short-duration (under 30 s) heat exposures. One of the many recent microbial reduction bioengineering research avenues harnesses electromagnetic energy for microbial reduction, with previous investigations demonstrating that infrared heaters are capable of the short temperature ramp time required for rapid heating investigations above 200°C. Therefore, this study employed a 6 kW infrared heater to determine the survivability of heat resistant Bacillus canaveralius 29669 to high-temperature, short-duration infrared temperatures. While B. canaveralius 29669 spores can survive microbial heat reduction processes above 200°C, we found evidence suggesting that the 500°C for 0.5 s temperature sterilization specification for Planetary Protection should be updated. This research presents spore survival data and a corresponding model pointing to a re-evaluation of the recommended HMR exposure of 500°C for 0.5 s, while simultaneously meeting requirements on the forward biological contamination of solar system bodies and opening up design possibilities for future spacecraft hardware.