Deniz Yılmaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Deniz Yılmaz has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Kamil Kayabali
Department of Geological Engineering, Ankara University, 06830, Ankara, Türkiye
6 shared publications - Muhammet Beyhan
Öksüt Mining (Centerra Gold Inc.)
3 shared publications - Mehmet Can Balcı
Department of Civil Engineering, Batman University, Batman 72100, Türkiye
2 shared publications - Nagaraj Hb
Department of Civil Engineering, B.M.S College of Engineering, Bangalore, India
2 shared publications - Elif Avşar1 shared publication
- H.B. Nagaraj
B.M.S College Of Engineering, Bangalore, India
1 shared publication
Latest Publications
- 1 January 2025
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. 176 (176) , 1-2
Effect of Degree of Saturation on Consolidation Parameters of Fine-Grained Soils
Terzaghi (1943)'s theory of consolidation phenomenon has some limitations for unsaturated geological environments in nature. Additionally, soils are subjected to consolidation tests under partially saturation conditions. The scope of this study is to illustrate the effect of degree of saturation (Sr) on the consolidation parameters using remolded soil samples. For this purpose, swelling pressure, compression index (cc), re-compression index (cr), coefficient of consolidation (cv), and pre-consolidation stress (σp') were determined for the samples having different degrees of saturation and plasticity (PI). The consolidation parameters obtained from “undersaturated” remolded samples with varying degrees of saturation were compared with the consolidation parameters obtained from “fully saturated” remolded samples to illustrate which parameters of consolidation are affected most by the degree of saturation. The effect of swelling of partially saturated samples was eliminated prior to conducting oedometer tests. Results indicated a meaningful relationship between the compression index and the degree of saturation, though the relationship with the recompression index was less certain. Pre-consolidation stress generally decreased as saturation increased, while no definitive trend was observed between the degree of saturation and the consolidation coefficient. Overall, most consolidation parameters were found to be somewhat affected by the degree of saturation.
- 1 January 2025
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. 176 (176) , 1-2
Effect of Degree of Saturation on Consolidation Parameters of Fine-Grained Soils
Terzaghi (1943)'s theory of consolidation phenomenon has some limitations for unsaturated geological environments in nature. Additionally, soils are subjected to consolidation tests under partially saturation conditions. The scope of this study is to illustrate the effect of degree of saturation (Sr) on the consolidation parameters using remolded soil samples. For this purpose, swelling pressure, compression index (cc), re-compression index (cr), coefficient of consolidation (cv), and pre-consolidation stress (σp') were determined for the samples having different degrees of saturation and plasticity (PI). The consolidation parameters obtained from “undersaturated” remolded samples with varying degrees of saturation were compared with the consolidation parameters obtained from “fully saturated” remolded samples to illustrate which parameters of consolidation are affected most by the degree of saturation. The effect of swelling of partially saturated samples was eliminated prior to conducting oedometer tests. Results indicated a meaningful relationship between the compression index and the degree of saturation, though the relationship with the recompression index was less certain. Pre-consolidation stress generally decreased as saturation increased, while no definitive trend was observed between the degree of saturation and the consolidation coefficient. Overall, most consolidation parameters were found to be somewhat affected by the degree of saturation.
- Open Access
- 1 January 2025
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. 176 (176) , 1-2
Reply to: “Discussion: Determination of Atterberg Limits Using the Vane Shear Test Method [Bull. Min. Res. Exp. (2024) 174: 1–10]”
The main focus of the criticisms raised by O'Kelly and Soltani (2025) (hereafter referred to as discussers) to the authors' article in Bulletin of Mineral Research and Exploration (174, 1-10) is to examine the veracity of the strength-based equations presented by Kayabalı et al. (2024). The discussers applied the predictive equations proposed by the authors to dissimilar soils in the two articles (Kayabalı et al., 2015a; Kayabalı et al., 2015b) published earlier by the lead author with his research group. The discussers showed that the predictive equations 6 and 7 given by Kayabalı et al. (2024) yield extremely high values of liquid limit (LL) and plastic limit (PL) when applied to dissimilar soils. Further, discussers argued that the approach proposed by Kayabalı et al. (2024) led to erroneous results in determining soil classes.
- 1 January 2025
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. 176 (176) , 1-2
Open AccessReply to: “Discussion: Determination of Atterberg Limits Using the Vane Shear Test Method [Bull. Min. Res. Exp. (2024) 174: 1–10]”
The main focus of the criticisms raised by O'Kelly and Soltani (2025) (hereafter referred to as discussers) to the authors' article in Bulletin of Mineral Research and Exploration (174, 1-10) is to examine the veracity of the strength-based equations presented by Kayabalı et al. (2024). The discussers applied the predictive equations proposed by the authors to dissimilar soils in the two articles (Kayabalı et al., 2015a; Kayabalı et al., 2015b) published earlier by the lead author with his research group. The discussers showed that the predictive equations 6 and 7 given by Kayabalı et al. (2024) yield extremely high values of liquid limit (LL) and plastic limit (PL) when applied to dissimilar soils. Further, discussers argued that the approach proposed by Kayabalı et al. (2024) led to erroneous results in determining soil classes.
- 22 November 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (4) , 5639-5651
An Attempt to Predict the Effective Angle of Internal Friction for Remolded Clayey Soils Using the Vane Shear Test: Some Important Implications
- 22 November 2023
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (4) , 5639-5651
An Attempt to Predict the Effective Angle of Internal Friction for Remolded Clayey Soils Using the Vane Shear Test: Some Important Implications
- Open Access
- 11 September 2023
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. early view (early view) , 1-10
Determination of Atterberg Limits using the vane shear test method
Atterberg limits are important index parameters used to classify soils for various engineering applications. Engineering properties of soils are predicted through simple correlations with index properties and thereby the engineering behavior of soils are qualitatively assessed. There are two popular methods of determining liquid limit, and plastic limit is commonly determined adopting rolling thread methods. To avoid operator related variations in determining plastic limit by conventional method, some researchers have explored using cone method as an alternative. However, there is no consensus about the depth of penetration to reckon the end of plastic state. Though various other test methods have been developed to determine plastic limit (like roll plate device), cone penetration with its limitation of determining plastic limit, is the only method to determine both liquid and plastic limit of soils. Since laboratory vane shear test is a simple and reliable method of determining undrained strength of fine-grained soils, the authors have explored to determine both liquid and plastic limits through correlations developed between undrained strength and water content over a range of consistencies between liquid and plastic states. This would eliminate determining liquid and plastic limit separately without sacrificing the reliability of results.
- 11 September 2023
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. early view (early view) , 1-10
Open AccessDetermination of Atterberg Limits using the vane shear test method
Atterberg limits are important index parameters used to classify soils for various engineering applications. Engineering properties of soils are predicted through simple correlations with index properties and thereby the engineering behavior of soils are qualitatively assessed. There are two popular methods of determining liquid limit, and plastic limit is commonly determined adopting rolling thread methods. To avoid operator related variations in determining plastic limit by conventional method, some researchers have explored using cone method as an alternative. However, there is no consensus about the depth of penetration to reckon the end of plastic state. Though various other test methods have been developed to determine plastic limit (like roll plate device), cone penetration with its limitation of determining plastic limit, is the only method to determine both liquid and plastic limit of soils. Since laboratory vane shear test is a simple and reliable method of determining undrained strength of fine-grained soils, the authors have explored to determine both liquid and plastic limits through correlations developed between undrained strength and water content over a range of consistencies between liquid and plastic states. This would eliminate determining liquid and plastic limit separately without sacrificing the reliability of results.
- 28 June 2023
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 41 (8) , 4473-4485
Development of a Single-Point Method to Determine Soil Plastic Limit Using Fall-Cone Data
- 28 June 2023
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 41 (8) , 4473-4485
Development of a Single-Point Method to Determine Soil Plastic Limit Using Fall-Cone Data
- 20 March 2023
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. 173, 1
A Simple and Practical Tool for Indirect Determination of the Unconfined Compressive Strength of Most Common Construction Materials
Determination of the unconfined compressive strength (UCS) of construction materials in the laboratory is tedious and time-consuming. There have been many attempts to indirectly predict UCS using simpler tools and techniques. One of them is the nail gun. The scope of this investigation is to design a nailer which can be applied all construction materials whose UCS range from 1-100 MPa. In the research, rocks, bricks, and concretes prepared in different cement/sand ratios with different strength ranges were used as materials. The unconfined compressive strength of the materials used in the experiments was first determined by conventional compression tests. The nail penetration depths were determined by conducting experiments on the same materials using a nailer with two different energy levels. An empirical relationship was developed by using nail penetration depths, driving energies, and nail diameters as the independent variables and the UCS determined by the conventional method as the dependent variable. According to the empirical relationship determined by multiple regression analysis, the UCS of building materials can be estimated with significance level of 99% by the nail penetration method. The research also revealed that the UCS of rocks might have a coefficient of variation as high as 30%.
- 20 March 2023
- Published by Bulletin of the Mineral Research and Exploration in Bulletin Of The Mineral Research and Exploration
- Vol. 173, 1
A Simple and Practical Tool for Indirect Determination of the Unconfined Compressive Strength of Most Common Construction Materials
Determination of the unconfined compressive strength (UCS) of construction materials in the laboratory is tedious and time-consuming. There have been many attempts to indirectly predict UCS using simpler tools and techniques. One of them is the nail gun. The scope of this investigation is to design a nailer which can be applied all construction materials whose UCS range from 1-100 MPa. In the research, rocks, bricks, and concretes prepared in different cement/sand ratios with different strength ranges were used as materials. The unconfined compressive strength of the materials used in the experiments was first determined by conventional compression tests. The nail penetration depths were determined by conducting experiments on the same materials using a nailer with two different energy levels. An empirical relationship was developed by using nail penetration depths, driving energies, and nail diameters as the independent variables and the UCS determined by the conventional method as the dependent variable. According to the empirical relationship determined by multiple regression analysis, the UCS of building materials can be estimated with significance level of 99% by the nail penetration method. The research also revealed that the UCS of rocks might have a coefficient of variation as high as 30%.
- Open Access
- 3 March 2021
- Published by Copernicus GmbH
Investigation of failure and damage processes of andesitic rocks
In this research, failure and deformation processes of andesitic rocks are investigated through laboratory and discrete element modeling (DEM) analysis to reveal the transition of the cracking, namely from microscale to mesoscale (lab scale). For this purpose, the mechanical properties of Ankara andesites were initially investigated by performing uniaxial - triaxial compressive and indirect tensile laboratory tests. Further, these properties were used as reference parameters for the calibration process in a numerical model, generated through a three-dimensional open source code (Yade) based on the discrete element method (DEM). Our results show that during the linear-elastic region of the stress-strain curve, the major mechanism of rock behavior is driven by tensile cracks. When the crack damage threshold is reached, as a result of plastic strain, the strength related to the inherent cohesion significantly decreases and damage in the rock cannot be prevented anymore. At the peak stress of the curve, both tensile and shear cracks accumulate, intensively. Even the mesoscale failure mechanism is controlled by shearing at the residual stage of the yielding, based on the micro-scale process in the DEM model, the number of micro shear cracks is very limited compared to the tensile ones. This finding shows that the friction takes the control of the damage process as the only driving force during residual phase time.
- 3 March 2021
- Published by Copernicus GmbH
Open AccessInvestigation of failure and damage processes of andesitic rocks
In this research, failure and deformation processes of andesitic rocks are investigated through laboratory and discrete element modeling (DEM) analysis to reveal the transition of the cracking, namely from microscale to mesoscale (lab scale). For this purpose, the mechanical properties of Ankara andesites were initially investigated by performing uniaxial - triaxial compressive and indirect tensile laboratory tests. Further, these properties were used as reference parameters for the calibration process in a numerical model, generated through a three-dimensional open source code (Yade) based on the discrete element method (DEM). Our results show that during the linear-elastic region of the stress-strain curve, the major mechanism of rock behavior is driven by tensile cracks. When the crack damage threshold is reached, as a result of plastic strain, the strength related to the inherent cohesion significantly decreases and damage in the rock cannot be prevented anymore. At the peak stress of the curve, both tensile and shear cracks accumulate, intensively. Even the mesoscale failure mechanism is controlled by shearing at the residual stage of the yielding, based on the micro-scale process in the DEM model, the number of micro shear cracks is very limited compared to the tensile ones. This finding shows that the friction takes the control of the damage process as the only driving force during residual phase time.