Wang Zekui Yang Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wang Zekui Yang Yang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Bo Lv
College of Environmental and Chemical Engineering, Yanshan University, Qinhuangdao 066004, China
1 shared publication - Chen Chen
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao, China
1 shared publication - Fucheng Zhang
College of Metallurgy and Energy, North China University of Science and Technology, Tangshan 063210, China
1 shared publication - Yanguo Li
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao, China
1 shared publication - Zekui Wang
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China
1 shared publication - Zhinan Yang
College of Metallurgy and Energy, North China University of Science and Technology, Tangshan, China
1 shared publication
Latest Publications
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (8) , 154-164
Effect of Ni and Cu Alloying on Microstructure and Mechanical Properties of Fe-Mn-Al-C Austenitic Lightweight Steel
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (8) , 154-164
Effect of Ni and Cu Alloying on Microstructure and Mechanical Properties of Fe-Mn-Al-C Austenitic Lightweight Steel
- Open Access
Effect of Surface Impacting Parameters on Wear Resistance of High Manganese Steel
High manganese steel has always been subjected to pre-hardening treatment before use owing to its low initial strength. Therefore, cast high manganese steel was pre-hardened in this work by surface impacting treatment under different parameters to evaluate its state. The microstructures, hardening characteristics, and wear resistances of the pre-hardened high manganese steel samples were all investigated. The results indicated that increasing the sample temperature, reducing the impact pin size, and increasing the impact times on a single-point can enhance the surface hardening effect to different degrees. Dislocations and deformation twins were produced on the top surface and within a certain depth of test steel under different impacting conditions. The optimal hardening effect of test steel was achieved at a temperature of 300 °C, a pin size of 10 × 10 mm2, and 9 impacts on a single point. The surface hardness of the treated sample reached 542 HV. For friction and wear testing, the best wear resistance was achieved at a temperature of 300 °C, a pin size of 10 × 10 mm2, and 3 impacts on a single point with a surface hardness of 446 HV. Further enhancement in impact hardening effect resulted in microcracking along the surface of test steel. In turn, the induced embrittlement led to the poor wear resistance.
Open AccessEffect of Surface Impacting Parameters on Wear Resistance of High Manganese Steel
High manganese steel has always been subjected to pre-hardening treatment before use owing to its low initial strength. Therefore, cast high manganese steel was pre-hardened in this work by surface impacting treatment under different parameters to evaluate its state. The microstructures, hardening characteristics, and wear resistances of the pre-hardened high manganese steel samples were all investigated. The results indicated that increasing the sample temperature, reducing the impact pin size, and increasing the impact times on a single-point can enhance the surface hardening effect to different degrees. Dislocations and deformation twins were produced on the top surface and within a certain depth of test steel under different impacting conditions. The optimal hardening effect of test steel was achieved at a temperature of 300 °C, a pin size of 10 × 10 mm2, and 9 impacts on a single point. The surface hardness of the treated sample reached 542 HV. For friction and wear testing, the best wear resistance was achieved at a temperature of 300 °C, a pin size of 10 × 10 mm2, and 3 impacts on a single point with a surface hardness of 446 HV. Further enhancement in impact hardening effect resulted in microcracking along the surface of test steel. In turn, the induced embrittlement led to the poor wear resistance.