Salvador Apolinar Trujillo-Pérez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Salvador Apolinar Trujillo-Pérez has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Luis Américo Carrasco-Venegas
Centro de Investigación en Bioenergía, Universidad Nacional del Callao, Callao 15001, Peru
5 shared publications - Luz Genara Castañeda-Pérez
Facultad de Ciencias Naturales y Matemática, Universidad Nacional Federico Villareal, Lima 15001, Peru
5 shared publications - José Vulfrano González-Fernández
Instituto Tecnológico de San Luis Potosí, Tecnológico Nacional de México, San Luis Potosi 78436, Mexico
4 shared publications - Juan Taumaturgo Medina-Collana
Faculty of Chemical Engineering, Centro de Investigación para la Educación, National University of Callao, Juan Pablo II 306 Avenue, Callao 07011, Peru
4 shared publications - César Gutiérrez-Cuba
Facultad de Ingeniería Química, Universidad Nacional del Callao, Callao 15001, Peru
2 shared publications - Daril Giovanni Martínez-Hilario
Facultad de Ingeniería Química, Universidad Nacional del Callao, Callao 07011, Peru
2 shared publications
Latest Publications
- Open Access
Study of the Degradation Kinetics and Photocatalytic Mineralization of the Dye 2-(4-Amino-2-Nitrophenyl)-1,3-Benzothiazole: Effect of TiO2 Dosage, pH, and Aeration on COD
The objective of this study was to evaluate the solar photocatalytic degradation of the disperse textile dye 2-(4-amino-2-nitrophenyl)-1,3-benzothiazole using titanium dioxide nanoparticles (TiO2 P25) under a mean solar irradiance of 492 ± 58 W/m2, evaluating the effects of pH, photocatalyst concentration, and continuous aeration on process efficiency. The degradation of the dye was determined by monitoring its concentration by UV–Visible spectrophotometry, while the mineralization was evaluated by chemical oxygen demand (COD). Likewise, kinetic behavior was analyzed using pseudo-first-order and pseudo-second-order models. The results showed that the degradation efficiency increased with the concentration of TiO2, reaching the highest yield with 400 ppm of TiO2 and continuous aeration, which confirms that both variables are determining operating factors for maximizing photocatalytic efficiency. pH exerted a significant influence on the activity of the system, obtaining the highest degradation efficiencies and the greatest reductions in COD under slightly alkaline conditions (pH 8–9), a behavior attributed to the greater colloidal stability of TiO2 and the modification of its surface properties with respect to its point of zero charge (pHpzc ≈ 6.2). The pseudo-second-order model generally provided an adequate empirical description of the experimental data; however, the best-fitting model varied depending on the experimental condition. The simultaneous decrease in the concentration of the dye and the COD confirmed that the treatment produced not only the decolorization of the solution, but also the progressive oxidation of the organic matter. Integrating kinetic analysis with the simultaneous assessment of decolorization and COD enabled clear experimental differentiation between adsorption and photocatalysis, strengthening the interpretation of TiO2-based solar photocatalytic systems. In conclusion, solar photocatalysis using TiO2 and the optimization of operational variables constitute an effective treatment strategy that takes advantage of solar irradiation as the primary energy source, thereby reducing dependence on conventional artificial UV irradiation. Within the scope of this study, the combination of solar radiation, continuous aeration and appropriate operating conditions demonstrated promising potential for the treatment of textile wastewater containing persistent dyes.
Open AccessStudy of the Degradation Kinetics and Photocatalytic Mineralization of the Dye 2-(4-Amino-2-Nitrophenyl)-1,3-Benzothiazole: Effect of TiO2 Dosage, pH, and Aeration on COD
The objective of this study was to evaluate the solar photocatalytic degradation of the disperse textile dye 2-(4-amino-2-nitrophenyl)-1,3-benzothiazole using titanium dioxide nanoparticles (TiO2 P25) under a mean solar irradiance of 492 ± 58 W/m2, evaluating the effects of pH, photocatalyst concentration, and continuous aeration on process efficiency. The degradation of the dye was determined by monitoring its concentration by UV–Visible spectrophotometry, while the mineralization was evaluated by chemical oxygen demand (COD). Likewise, kinetic behavior was analyzed using pseudo-first-order and pseudo-second-order models. The results showed that the degradation efficiency increased with the concentration of TiO2, reaching the highest yield with 400 ppm of TiO2 and continuous aeration, which confirms that both variables are determining operating factors for maximizing photocatalytic efficiency. pH exerted a significant influence on the activity of the system, obtaining the highest degradation efficiencies and the greatest reductions in COD under slightly alkaline conditions (pH 8–9), a behavior attributed to the greater colloidal stability of TiO2 and the modification of its surface properties with respect to its point of zero charge (pHpzc ≈ 6.2). The pseudo-second-order model generally provided an adequate empirical description of the experimental data; however, the best-fitting model varied depending on the experimental condition. The simultaneous decrease in the concentration of the dye and the COD confirmed that the treatment produced not only the decolorization of the solution, but also the progressive oxidation of the organic matter. Integrating kinetic analysis with the simultaneous assessment of decolorization and COD enabled clear experimental differentiation between adsorption and photocatalysis, strengthening the interpretation of TiO2-based solar photocatalytic systems. In conclusion, solar photocatalysis using TiO2 and the optimization of operational variables constitute an effective treatment strategy that takes advantage of solar irradiation as the primary energy source, thereby reducing dependence on conventional artificial UV irradiation. Within the scope of this study, the combination of solar radiation, continuous aeration and appropriate operating conditions demonstrated promising potential for the treatment of textile wastewater containing persistent dyes.
- Open Access
Modeling of Soluble and Biodegradable Contaminant Transport in Channels and Rivers
Accurate prediction of contaminant transport and self-purification processes in rivers remains challenging because pollutant dispersion, biochemical reactions, and hydrodynamic conditions interact across multiple spatial scales. This study aims to develop and compare mathematical models for soluble contaminant transport and biodegradable organic matter removal in channels and rivers. Unsteady advection–diffusion–reaction equations were formulated for one-dimensional (1D), two-dimensional (2D), and three-dimensional (3D) transport scenarios and solved through numerical techniques based on the transformation of partial differential equations into systems of ordinary differential or algebraic equations. In parallel, the classical Streeter–Phelps model and an extended formulation incorporating turbulent diffusion were implemented to evaluate organic load degradation and oxygen deficit dynamics. Simulations were performed using a Matlab R2019a-based computational framework under representative hydraulic and reaction conditions obtained from literature data and empirical correlations. The results showed that, under specific conditions, the 3D model reproduced trends comparable to those predicted by the 2D model, while the latter approached the behavior of the 1D formulation. The Streeter–Phelps model predicted an organic load removal efficiency of 97.74%, a purification index of 1.9564, a critical time of 18.43 h, and a critical distance of 6.93 km. These findings provide a useful framework for river water-quality assessment and support future applications involving complex hydrodynamic and pollutant-loading scenarios.
Open AccessModeling of Soluble and Biodegradable Contaminant Transport in Channels and Rivers
Accurate prediction of contaminant transport and self-purification processes in rivers remains challenging because pollutant dispersion, biochemical reactions, and hydrodynamic conditions interact across multiple spatial scales. This study aims to develop and compare mathematical models for soluble contaminant transport and biodegradable organic matter removal in channels and rivers. Unsteady advection–diffusion–reaction equations were formulated for one-dimensional (1D), two-dimensional (2D), and three-dimensional (3D) transport scenarios and solved through numerical techniques based on the transformation of partial differential equations into systems of ordinary differential or algebraic equations. In parallel, the classical Streeter–Phelps model and an extended formulation incorporating turbulent diffusion were implemented to evaluate organic load degradation and oxygen deficit dynamics. Simulations were performed using a Matlab R2019a-based computational framework under representative hydraulic and reaction conditions obtained from literature data and empirical correlations. The results showed that, under specific conditions, the 3D model reproduced trends comparable to those predicted by the 2D model, while the latter approached the behavior of the 1D formulation. The Streeter–Phelps model predicted an organic load removal efficiency of 97.74%, a purification index of 1.9564, a critical time of 18.43 h, and a critical distance of 6.93 km. These findings provide a useful framework for river water-quality assessment and support future applications involving complex hydrodynamic and pollutant-loading scenarios.
- Open Access
- 20 March 2024
- Published by MDPI AG in Chemengineering
- Vol. 8 (2) , 35
Profile of the Effectiveness Factor under Optimal Operating Conditions for the Conversion of Ortho-Xylene to Phthalic Anhydride in a Fixed-Bed Tubular Reactor
The objective of this research is to find the effectiveness factor of the catalyst particles for the most favorable conditions of the phthalic anhydride production in a fixed bed reactor, with the aim of achieving the highest rate of phthalic anhydride production compared to other secondary products and analyzing the areas of lower effectiveness for the modification of the reactor design. Initially, the material and the energy balances in the catalytic bed are solved to obtain the concentration and temperature profiles based on the radius and length of the reactor, using polymath software(Polymath® v6.2 Software Minitab 19 Matlab 2019) with the data from literature. Once the profiles reproducibility was verified using the initial data (inlet temperature, pressure in the reactor, reactor wall temperature, reactor radius and mass flow rate) the experimental design 35 carry out, which generates 243 “experiments”, whose response variable (phthalic anhydride concentration) was obtained using Matlab. Subsequently, the variables were analyzed using the Minitab 18® that, through the response surface analysis method, allowed us to obtain the optimal values of the tested variables. Then, Subsequently, material and energy balances coupled with Fourier and Fick’s laws, along with the effectiveness factor equation, were applied, resulting in the generation of 9 coupled differential equations. Upon implementing the finite difference method, this yielded 90 nonlinear algebraic equations, which were solved using the Polymath software. A total of 78 particles were preselected based on their radial and axial positions to determine the effectiveness factor profile, with values ranging from 0.83 to near unity. The lower values correspond to the points with higher temperature, as evidenced by the calculations performed.
- 20 March 2024
- Published by MDPI AG in Chemengineering
- Vol. 8 (2) , 35
Open AccessProfile of the Effectiveness Factor under Optimal Operating Conditions for the Conversion of Ortho-Xylene to Phthalic Anhydride in a Fixed-Bed Tubular Reactor
The objective of this research is to find the effectiveness factor of the catalyst particles for the most favorable conditions of the phthalic anhydride production in a fixed bed reactor, with the aim of achieving the highest rate of phthalic anhydride production compared to other secondary products and analyzing the areas of lower effectiveness for the modification of the reactor design. Initially, the material and the energy balances in the catalytic bed are solved to obtain the concentration and temperature profiles based on the radius and length of the reactor, using polymath software(Polymath® v6.2 Software Minitab 19 Matlab 2019) with the data from literature. Once the profiles reproducibility was verified using the initial data (inlet temperature, pressure in the reactor, reactor wall temperature, reactor radius and mass flow rate) the experimental design 35 carry out, which generates 243 “experiments”, whose response variable (phthalic anhydride concentration) was obtained using Matlab. Subsequently, the variables were analyzed using the Minitab 18® that, through the response surface analysis method, allowed us to obtain the optimal values of the tested variables. Then, Subsequently, material and energy balances coupled with Fourier and Fick’s laws, along with the effectiveness factor equation, were applied, resulting in the generation of 9 coupled differential equations. Upon implementing the finite difference method, this yielded 90 nonlinear algebraic equations, which were solved using the Polymath software. A total of 78 particles were preselected based on their radial and axial positions to determine the effectiveness factor profile, with values ranging from 0.83 to near unity. The lower values correspond to the points with higher temperature, as evidenced by the calculations performed.
- Open Access
Viscosity Factor (VF) Complementary to the Statistical Indicators Associated with the Rheological Behavior of Aqueous Solutions of Polyvinyl Alcohol
The rheological behavior of aqueous solutions of polyvinyl alcohol at 4, 6, 8 and 10% by weight has been studied and evaluated at temperatures of 20, 25, 30 and 35 °C, using five non-Newtonian fluid models independent of time: Ferrys, Robertson-Stiff, Williamson, Sisko, and Ellis de Haven. The classical method consists in carrying out regression analysis. Using a comparative procedure of determination coefficients and variances, the model that most appropriately adjusts the experimental data to said model is selected. From the statistical point of view, the Sisko and Robertson-Stiff models present better regression parameters; to better specify the choice of the respective rheological model, a new factor has been proposed in the literature, the viscosity factor (VF), which expresses the relationship between apparent and dynamic viscosity. The analysis of this factor for the five models confirms the greater stability of the Ellis de Haven model in terms of the coefficient of variation of the VF. The value of VF fluctuates between 1 and 2 for all ranges of temperature and concentration experienced for vinyl alcohol solutions. As a consequence of the above, for the choice of the non-Newtonian fluid model associated with the rheology of the aqueous solution of polyvinyl alcohol, it is necessary to analyze the statistical parameters and the VF factor simultaneously.
Open AccessViscosity Factor (VF) Complementary to the Statistical Indicators Associated with the Rheological Behavior of Aqueous Solutions of Polyvinyl Alcohol
The rheological behavior of aqueous solutions of polyvinyl alcohol at 4, 6, 8 and 10% by weight has been studied and evaluated at temperatures of 20, 25, 30 and 35 °C, using five non-Newtonian fluid models independent of time: Ferrys, Robertson-Stiff, Williamson, Sisko, and Ellis de Haven. The classical method consists in carrying out regression analysis. Using a comparative procedure of determination coefficients and variances, the model that most appropriately adjusts the experimental data to said model is selected. From the statistical point of view, the Sisko and Robertson-Stiff models present better regression parameters; to better specify the choice of the respective rheological model, a new factor has been proposed in the literature, the viscosity factor (VF), which expresses the relationship between apparent and dynamic viscosity. The analysis of this factor for the five models confirms the greater stability of the Ellis de Haven model in terms of the coefficient of variation of the VF. The value of VF fluctuates between 1 and 2 for all ranges of temperature and concentration experienced for vinyl alcohol solutions. As a consequence of the above, for the choice of the non-Newtonian fluid model associated with the rheology of the aqueous solution of polyvinyl alcohol, it is necessary to analyze the statistical parameters and the VF factor simultaneously.
- Open Access
Analysis of the Effectiveness Factor in a Fixed-Bed Tubular Reactor System: Catalytic Dehydrogenation of Cyclohexanol
The modeling and simulation of the catalytic dehydrogenation process of cyclohexanol in a fixed-bed catalytic reactor is presented, leading to finding the relationship between the effectiveness factor, the Thiele modulus, and the Weisz–Prater modulus of the catalyst particles with respect to their axial and radial position, for which the external conditions of concentration and temperature around each particle were previously obtained by applying the material and energy balances in the catalyst bed considering a two-dimensional pseudo-homogeneous model with radial diffusion. Subsequently, the material balances are established in terms of the molar flux density and conversion, the energy balance in terms of the heat flux density, Fick’s law, Fourier’s law, and the differential form of the effectiveness factor non-isothermal for each particle chosen based on the proposed meshing. The Thiele modulus calculated for most of the points is between 0.8 and 0.25, with a tendency towards the lower limit, and the theoretical values established as the limit for the Thiele modulus fluctuate between . Therefore, the effectiveness factor analyzed is between 1 and ; this indicates that both the reaction speed as well as the diffusion speed within the particle have an influence on the intraparticle process, which is confirmed by the calculation of the Weisz–Prater modulus whose values are not 1 nor 1. The results obtained are subjected to a statistical test leading to analyzing whether there are significant differences both in the Thiele modulus, as well as in the effectiveness factor with respect to the radius and length of the reactor. It has been determined that there are no significant differences between the effectiveness factor with respect to the radius of the reactor; however, according to the analysis of variance, there are significant differences in the effectiveness factor with respect to length and, likewise, there are significant differences in the Thiele modulus and the Weisz–Prater modulus with respect to radius and length.Open AccessAnalysis of the Effectiveness Factor in a Fixed-Bed Tubular Reactor System: Catalytic Dehydrogenation of Cyclohexanol
The modeling and simulation of the catalytic dehydrogenation process of cyclohexanol in a fixed-bed catalytic reactor is presented, leading to finding the relationship between the effectiveness factor, the Thiele modulus, and the Weisz–Prater modulus of the catalyst particles with respect to their axial and radial position, for which the external conditions of concentration and temperature around each particle were previously obtained by applying the material and energy balances in the catalyst bed considering a two-dimensional pseudo-homogeneous model with radial diffusion. Subsequently, the material balances are established in terms of the molar flux density and conversion, the energy balance in terms of the heat flux density, Fick’s law, Fourier’s law, and the differential form of the effectiveness factor non-isothermal for each particle chosen based on the proposed meshing. The Thiele modulus calculated for most of the points is between 0.8 and 0.25, with a tendency towards the lower limit, and the theoretical values established as the limit for the Thiele modulus fluctuate between . Therefore, the effectiveness factor analyzed is between 1 and ; this indicates that both the reaction speed as well as the diffusion speed within the particle have an influence on the intraparticle process, which is confirmed by the calculation of the Weisz–Prater modulus whose values are not 1 nor 1. The results obtained are subjected to a statistical test leading to analyzing whether there are significant differences both in the Thiele modulus, as well as in the effectiveness factor with respect to the radius and length of the reactor. It has been determined that there are no significant differences between the effectiveness factor with respect to the radius of the reactor; however, according to the analysis of variance, there are significant differences in the effectiveness factor with respect to length and, likewise, there are significant differences in the Thiele modulus and the Weisz–Prater modulus with respect to radius and length.