Cailing Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cailing Liu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Hao Yuan
College of Engineering, China Agricultural University, Beijing 100083/ China
4 shared publicationsChangqing Liu
School of Mechanical Engineering, Jiangsu Ocean University, Lianyungang
3 shared publicationsLei Dai
College of Engineering, China Agricultural University, Beijing 100083 / China
3 shared publicationsHongying Wang
College of Engineering, China Agricultural University, Beijing 100085, China
2 shared publicationsLiangju Wang
College of Engineering, China Agricultural University, Beijing 100085, China
2 shared publicationsMeng Jiang
College of Engineering, China Agricultural University, Beijing 100083/ China
2 shared publications
Latest Publications
- Open Access
- 1 August 2023
- Published by PAGEPress Publications in Journal of Agricultural Engineering
- Vol. 54 (2)
A novel method for measurement of the angle of repose of granular seeds in discrete element methods
Discrete element numerical simulations can help researchers find potential problems in the design phase, shortening the development cycle and reducing costs. In the field of agricultural engineering, more and more researchers are using discrete element methods (DEM) to assist in designing and optimising equipment parameters. Model parameters calibration is a prerequisite for discrete element numerical calculations, and the angle of repose (AoR) is commonly used to calibrate the parameters. However, the measurement of AoR in DEM was not seriously considered in industrial or academic fields. In practice, AoR is measured manually, using 2D digital image processing or using a 3D scan. However, reliable and consistent measurements of AoR in DEM are rarely mentioned. This study suggests an accurate and consistent way to measure AoR in DEM using a novel method to read particle coordinate information directly from the data file; then, the AoR is calculated by linearly fitting the centre coordinates of the outermost particles. Influences of input variables on AoR acquisition are discussed through several examples using customised templates with known angles. Then a comparative study of the accuracy of the measurement of AoR in DEM and the reliability of the parameter calibration results by the manual measurement, 2D digital image processing, and algorithm proposed in this paper was conducted. In case studies with four seed materials, this method prevented the subjective selection of AoR, improved the identification accuracy, and increased the precision and accuracy of DEM calibration. In addition, the time consumption for obtaining AoR using the novel method for measurement is much less than that of 2D.
- 1 August 2023
- Published by PAGEPress Publications in Journal of Agricultural Engineering
- Vol. 54 (2)
Open AccessA novel method for measurement of the angle of repose of granular seeds in discrete element methods
Discrete element numerical simulations can help researchers find potential problems in the design phase, shortening the development cycle and reducing costs. In the field of agricultural engineering, more and more researchers are using discrete element methods (DEM) to assist in designing and optimising equipment parameters. Model parameters calibration is a prerequisite for discrete element numerical calculations, and the angle of repose (AoR) is commonly used to calibrate the parameters. However, the measurement of AoR in DEM was not seriously considered in industrial or academic fields. In practice, AoR is measured manually, using 2D digital image processing or using a 3D scan. However, reliable and consistent measurements of AoR in DEM are rarely mentioned. This study suggests an accurate and consistent way to measure AoR in DEM using a novel method to read particle coordinate information directly from the data file; then, the AoR is calculated by linearly fitting the centre coordinates of the outermost particles. Influences of input variables on AoR acquisition are discussed through several examples using customised templates with known angles. Then a comparative study of the accuracy of the measurement of AoR in DEM and the reliability of the parameter calibration results by the manual measurement, 2D digital image processing, and algorithm proposed in this paper was conducted. In case studies with four seed materials, this method prevented the subjective selection of AoR, improved the identification accuracy, and increased the precision and accuracy of DEM calibration. In addition, the time consumption for obtaining AoR using the novel method for measurement is much less than that of 2D.
- 30 April 2023
- Published by INMA Bucharest-Romania in INMATEH Agricultural Engineering
- Vol. 69 (1) , 673-680
EFFECT OF CONTROLLED-RELEASE FERTILIZER ON MAIZE YIELD AND NUTRIENT UPTAKE UNDER A FERTILIZER ONE-TIME POINT-APPLIED SYSTEM
- 30 April 2023
- Published by INMA Bucharest-Romania in INMATEH Agricultural Engineering
- Vol. 69 (1) , 673-680
EFFECT OF CONTROLLED-RELEASE FERTILIZER ON MAIZE YIELD AND NUTRIENT UPTAKE UNDER A FERTILIZER ONE-TIME POINT-APPLIED SYSTEM
- Open Access
- 1 January 2023
- Published by International Journal of Agricultural and Biological Engineering (IJABE) in International Journal of Agricultural and Biological Engineering
- Vol. 16 (6) , 37-47
Effects of different machine transplanting methods on the physiological and yield characteristics of late rice in China
To address problems caused by rice machine transplanting such as injury to the seedlings and recovery period that extend growth period, this study explored the effects of different machine transplanting methods on the physiological and yield characteristics of late rice in China, and determine the appropriate machine transplanting method for late rice, which was expected to provide a basis for high-yield and high-efficient cultivation of machine-transplanted late rice. Hybrid indica rice Taiyou 398 and conventional indica rice Jing Gangruanzhan were selected as the research objects, and large-pot carpet seedling machine transplanting (M1), conventional pot carpet seedling machine transplanting (M2) and ordinary carpet seedling machine transplanting (M3) were adopted respectively to analyze their effects on seedling quality, population physiological characteristics, yield and its components and economic benefits of late rice. The results showed that compared with M2 and M3, M1 achieved higher seedling quality, showing significant advantages in the early stage despite average root entwining force that met the requirement of machine transplanting. The seedlings transplanted using M1 had shorter recovery period after mechanical transplanting, with earlier tillering, earlier peak seedling, and slower declining of stems and tillers in the late stage; the peak seedling number was not high, but the effective tiller number and earbearing tiller percentage were significantly higher than those achieved by the other two machine transplanting methods. Also, M1 achieved stronger photosynthetic capacity of flag leaves before HS, with more photosynthetic products in stems and leaves transported to panicles and more efficiently after HS. Compared with seedlings transplanted using M2 and M3, the recovery period of those transplanted using M1 was shortened by 3 and 5 d, the heading stage (HS), and maturity stage (MS) were advanced, which effectively reduced the risk and impact of “cold dew wind” on machine-transplanted late rice. M1 had significant yield increase advantage and economic benefit, with better grain maturity, and “larger panicles, more panicles, more and fuller grains”. M1 achieved an average yield increase of 10.31%-11.10%, 20.67%-25.10% in 2 years, and an average income increase of 18.65%-131.06% and 62.85%-323.78%, respectively. Therefore, vigorously developing M1 is the key to the high-yield and high-efficient cultivation of machine-transplanted late rice in China. Keywords: large-pot carpet seedling, machine transplanting, late rice, physiological characteristics, seedling quality, yield DOI: 10.25165/j.ijabe.20231606.7764 Citation: Jia X, Li Y L, Song J N, Liu C L, Cao X L, Chen L C, et al. Effects of different machine transplanting methods on the physiological and yield characteristics of late rice in China. Int J Agric & Biol Eng, 2023; 16(6): 37–47.
- 1 January 2023
- Published by International Journal of Agricultural and Biological Engineering (IJABE) in International Journal of Agricultural and Biological Engineering
- Vol. 16 (6) , 37-47
Open AccessEffects of different machine transplanting methods on the physiological and yield characteristics of late rice in China
To address problems caused by rice machine transplanting such as injury to the seedlings and recovery period that extend growth period, this study explored the effects of different machine transplanting methods on the physiological and yield characteristics of late rice in China, and determine the appropriate machine transplanting method for late rice, which was expected to provide a basis for high-yield and high-efficient cultivation of machine-transplanted late rice. Hybrid indica rice Taiyou 398 and conventional indica rice Jing Gangruanzhan were selected as the research objects, and large-pot carpet seedling machine transplanting (M1), conventional pot carpet seedling machine transplanting (M2) and ordinary carpet seedling machine transplanting (M3) were adopted respectively to analyze their effects on seedling quality, population physiological characteristics, yield and its components and economic benefits of late rice. The results showed that compared with M2 and M3, M1 achieved higher seedling quality, showing significant advantages in the early stage despite average root entwining force that met the requirement of machine transplanting. The seedlings transplanted using M1 had shorter recovery period after mechanical transplanting, with earlier tillering, earlier peak seedling, and slower declining of stems and tillers in the late stage; the peak seedling number was not high, but the effective tiller number and earbearing tiller percentage were significantly higher than those achieved by the other two machine transplanting methods. Also, M1 achieved stronger photosynthetic capacity of flag leaves before HS, with more photosynthetic products in stems and leaves transported to panicles and more efficiently after HS. Compared with seedlings transplanted using M2 and M3, the recovery period of those transplanted using M1 was shortened by 3 and 5 d, the heading stage (HS), and maturity stage (MS) were advanced, which effectively reduced the risk and impact of “cold dew wind” on machine-transplanted late rice. M1 had significant yield increase advantage and economic benefit, with better grain maturity, and “larger panicles, more panicles, more and fuller grains”. M1 achieved an average yield increase of 10.31%-11.10%, 20.67%-25.10% in 2 years, and an average income increase of 18.65%-131.06% and 62.85%-323.78%, respectively. Therefore, vigorously developing M1 is the key to the high-yield and high-efficient cultivation of machine-transplanted late rice in China. Keywords: large-pot carpet seedling, machine transplanting, late rice, physiological characteristics, seedling quality, yield DOI: 10.25165/j.ijabe.20231606.7764 Citation: Jia X, Li Y L, Song J N, Liu C L, Cao X L, Chen L C, et al. Effects of different machine transplanting methods on the physiological and yield characteristics of late rice in China. Int J Agric & Biol Eng, 2023; 16(6): 37–47.
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 43 (spe)
PREDICTION OF DEM PARAMETERS OF COATED FERTILIZER PARTICLES BASED ON GA-BP NEURAL NETWORK
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 43 (spe)
Open AccessPREDICTION OF DEM PARAMETERS OF COATED FERTILIZER PARTICLES BASED ON GA-BP NEURAL NETWORK
- 31 December 2022
- Published by INMA Bucharest-Romania in INMATEH Agricultural Engineering
- Vol. 68 (3) , 781-788
EFFECT OF CONTROLLED-RELEASE FERTILIZER ON MAIZE YIELD AND NUTRIENT UPTAKE UNDER A ONE-TIME FERTILIZER LAYERED SYSTEM
- 31 December 2022
- Published by INMA Bucharest-Romania in INMATEH Agricultural Engineering
- Vol. 68 (3) , 781-788
EFFECT OF CONTROLLED-RELEASE FERTILIZER ON MAIZE YIELD AND NUTRIENT UPTAKE UNDER A ONE-TIME FERTILIZER LAYERED SYSTEM
- 30 April 2022
- Published by INMA Bucharest-Romania in INMATEH Agricultural Engineering
- Vol. 66 (1) , 101-110
RESEARCH ON DEM CALIBRATION OF CONTACT PARAMETERS OF COATED FERTILIZER
- 30 April 2022
- Published by INMA Bucharest-Romania in INMATEH Agricultural Engineering
- Vol. 66 (1) , 101-110
RESEARCH ON DEM CALIBRATION OF CONTACT PARAMETERS OF COATED FERTILIZER
- 11 January 2022
- Published by Elsevier in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
- Vol. 271, 120887
PLS-DA and Vis-NIR spectroscopy based discrimination of abdominal tissues of female rabbits
- 11 January 2022
- Published by Elsevier in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
- Vol. 271, 120887
PLS-DA and Vis-NIR spectroscopy based discrimination of abdominal tissues of female rabbits
- 1 January 2022
- Published by Elsevier in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
- Vol. 264, 120251
Early pregnancy diagnosis of rabbits: A non-invasive approach using Vis-NIR spatially resolved spectroscopy
- 1 January 2022
- Published by Elsevier in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
- Vol. 264, 120251
Early pregnancy diagnosis of rabbits: A non-invasive approach using Vis-NIR spatially resolved spectroscopy