Jun Xiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jun Xiao has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Maofei Geng
Hefei General Machinery Research Institute Co
2 shared publications - Qichao Yang
College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao, China
2 shared publications - Bing Li
Xidian University
1 shared publication Bo Lang
School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an, Shaanxi 710049, China
1 shared publication- Jie Zheng
The University of Texas at San Antonio
1 shared publication Liansheng Li
State Key Laboratory of Compressor Technology, Hefei General Machinery Research Institute, Hefei 230031, PR China
1 shared publication
Latest Publications
- 29 May 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (2) , 1676-1689
Analyses of gas pulsation characteristics in the discharge pipeline of a hyper compressor
For the analysis of gas pulsation characteristics in the pipeline systems of low density polyethylene (LDPE) hyper compressors, a time-domain calculation method for compressor pipeline gas pulsation based on real gas properties is proposed. First the thermophysical property tables are prepared with gas state parameters as independent and dependent variables. Then one-dimensional unsteady flow equations and characteristic equations for pipeline flow are established based on real gas properties. After setting pipeline parameters and boundary conditions, the flow equations are discretized using a two-step method at the inner points of the pipeline. The characteristic equations are discretized using the trapezoidal integration method at the boundary points. Thus, the time-domain solving of pulsating flow field in the pipeline is realized. A self-developed numerical code was used to conduct the time-domain calculation and analysis of gas pulsation in the discharge pipeline of a two-stage hyper compressor. The calculated pressure pulsation curves based on real gas properties are in good agreement with experimental data, with a maximum difference lower than 4% of the local average pressure, which is smaller than the difference between the results calculated based on the plane wave theory and the measured data. The analysis of gas pulsation characteristics shows that the pressure pulsation in the main pipeline is mainly contributed by the fundamental and second harmonics. The pressure pulsation in the safety valve branch is higher than that in the main pipeline, and the harmonic components falling into the acoustic resonance frequency range of this branch have significant amplitudes. The acoustic resonance frequency of the branch pipeline is not affected by the main pipeline. Pressure pulsation varies with changes in rotational speed and back pressure, and the pulsation level is more significantly affected by rotational speed compared to back pressure. The renovation scheme of connecting the safety valve branch and expansion tube in series can effectively reduce the pressure pulsation levels of the main pipeline and branch pipeline.
- 29 May 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (2) , 1676-1689
Analyses of gas pulsation characteristics in the discharge pipeline of a hyper compressor
For the analysis of gas pulsation characteristics in the pipeline systems of low density polyethylene (LDPE) hyper compressors, a time-domain calculation method for compressor pipeline gas pulsation based on real gas properties is proposed. First the thermophysical property tables are prepared with gas state parameters as independent and dependent variables. Then one-dimensional unsteady flow equations and characteristic equations for pipeline flow are established based on real gas properties. After setting pipeline parameters and boundary conditions, the flow equations are discretized using a two-step method at the inner points of the pipeline. The characteristic equations are discretized using the trapezoidal integration method at the boundary points. Thus, the time-domain solving of pulsating flow field in the pipeline is realized. A self-developed numerical code was used to conduct the time-domain calculation and analysis of gas pulsation in the discharge pipeline of a two-stage hyper compressor. The calculated pressure pulsation curves based on real gas properties are in good agreement with experimental data, with a maximum difference lower than 4% of the local average pressure, which is smaller than the difference between the results calculated based on the plane wave theory and the measured data. The analysis of gas pulsation characteristics shows that the pressure pulsation in the main pipeline is mainly contributed by the fundamental and second harmonics. The pressure pulsation in the safety valve branch is higher than that in the main pipeline, and the harmonic components falling into the acoustic resonance frequency range of this branch have significant amplitudes. The acoustic resonance frequency of the branch pipeline is not affected by the main pipeline. Pressure pulsation varies with changes in rotational speed and back pressure, and the pulsation level is more significantly affected by rotational speed compared to back pressure. The renovation scheme of connecting the safety valve branch and expansion tube in series can effectively reduce the pressure pulsation levels of the main pipeline and branch pipeline.
- Open Access
- 13 January 2024
- Published by Springer Nature
- p. 1-14
Analysis and Treatment of Gas Pulsation in the Pipeline of a Hydrogen Diaphragm Compressor
Based on the plane wave theory and the transfer matrix method, the modeling, calculation and analysis of gas pulsation in a complex pipeline system of a hydrogen diaphragm compressor were carried out. The calculations show that the gas pulsations of the intake and exhaust pipelines of the cylinder gradually attenuate along the pipeline upstream and downstream, and the gas pulsation of the exhaust pipeline of the second stage cylinder is larger. The gas pulsations of the exhaust pipelines of the first and second stage cylinders are significantly higher than the limit values of API 618. From the perspective of pulsation control, an attempt was made to add orifice plates at appropriate positions of the pipeline to reduce the pulsation amplitude. The trial calculations show that the added orifice plate can effectively reduce the maximum gas pulsation of the pipeline, and can provide a useful reference for the treatment of gas pulsation.
- 13 January 2024
- Published by Springer Nature
- p. 1-14
Open AccessAnalysis and Treatment of Gas Pulsation in the Pipeline of a Hydrogen Diaphragm Compressor
Based on the plane wave theory and the transfer matrix method, the modeling, calculation and analysis of gas pulsation in a complex pipeline system of a hydrogen diaphragm compressor were carried out. The calculations show that the gas pulsations of the intake and exhaust pipelines of the cylinder gradually attenuate along the pipeline upstream and downstream, and the gas pulsation of the exhaust pipeline of the second stage cylinder is larger. The gas pulsations of the exhaust pipelines of the first and second stage cylinders are significantly higher than the limit values of API 618. From the perspective of pulsation control, an attempt was made to add orifice plates at appropriate positions of the pipeline to reduce the pulsation amplitude. The trial calculations show that the added orifice plate can effectively reduce the maximum gas pulsation of the pipeline, and can provide a useful reference for the treatment of gas pulsation.
- 8 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (5) , 2404-2415
Analysis and treatment of gas pulsation in the pipeline of a hyper compressor
The compressor discharge pressure of a polyethylene plant in Yanshan Petrochemical Company exceeds 170 MPa, and the gas pulsation in some pipe sections is large, which leads to strong vibration of pipeline elements. The acoustic modeling and analysis of gas pulsation characteristics were carried out around the hyper compressor pipeline system of the polyethylene device. The non-invasive strain–pressure method was used to indirectly measure the pressure pulsation data in the high-pressure pipeline, and the test results were in good agreement with the simulations. On this basis, based on the acoustic analysis, the treatment measures to effectively suppress the gas pulsation in the high-pressure pipeline were further proposed.
- 8 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (5) , 2404-2415
Analysis and treatment of gas pulsation in the pipeline of a hyper compressor
The compressor discharge pressure of a polyethylene plant in Yanshan Petrochemical Company exceeds 170 MPa, and the gas pulsation in some pipe sections is large, which leads to strong vibration of pipeline elements. The acoustic modeling and analysis of gas pulsation characteristics were carried out around the hyper compressor pipeline system of the polyethylene device. The non-invasive strain–pressure method was used to indirectly measure the pressure pulsation data in the high-pressure pipeline, and the test results were in good agreement with the simulations. On this basis, based on the acoustic analysis, the treatment measures to effectively suppress the gas pulsation in the high-pressure pipeline were further proposed.
- Open Access
- 29 September 2022
- Published by Wiley in Shock and Vibration
- Vol. 2022, 1-14
A New Dynamic Balance Framework Based on Blind Source Separation under Multiple Fault Conditions
Accordingly, the mass unbalance of the rotors is usually the major cause of excessive vibration. The information extracted at the fundamental frequency is often employed to fix the unbalance issue. However, other rotor faults like rotor bending and bearing-failure effect also generate additional components to the characteristics. Thus, it is necessary to isolate the corresponding features and obtain the intrinsic causes of the multiple failures. In this paper, a productive hybrid method is successfully developed to deal with the root mass unbalance problem with additional force interference by integrating the superiority of different methods, including Ensemble Empirical Mode Decomposition (EEMD) and Nonnegative Matrix Factorization (NMF), where EEMD is used to obtain sensitive IMFs and NMF is employed to acquire the inherent source signal, respectively. Meanwhile, a root dynamic balancing and implemental framework is also developed to accomplish the task of vibration reduction. For verification, a serial of simulations and experimental investigations have been analysed to demonstrate the preferable potentialities of the proposed method. In particular, a standard Bently Nevada rotor rig with a specifically designed device was employed to simulate appended faults by adjusting the additional forces during the experimental steps. The analysis results show that the proposed method can isolate and extract the unbalance faults from the raw vibration signals and achieve accurate correction balancers, where a nearly identical correction angle has been achieved, which indicates that the optimal installation position has been successfully figured out.
- 29 September 2022
- Published by Wiley in Shock and Vibration
- Vol. 2022, 1-14
Open AccessA New Dynamic Balance Framework Based on Blind Source Separation under Multiple Fault Conditions
Accordingly, the mass unbalance of the rotors is usually the major cause of excessive vibration. The information extracted at the fundamental frequency is often employed to fix the unbalance issue. However, other rotor faults like rotor bending and bearing-failure effect also generate additional components to the characteristics. Thus, it is necessary to isolate the corresponding features and obtain the intrinsic causes of the multiple failures. In this paper, a productive hybrid method is successfully developed to deal with the root mass unbalance problem with additional force interference by integrating the superiority of different methods, including Ensemble Empirical Mode Decomposition (EEMD) and Nonnegative Matrix Factorization (NMF), where EEMD is used to obtain sensitive IMFs and NMF is employed to acquire the inherent source signal, respectively. Meanwhile, a root dynamic balancing and implemental framework is also developed to accomplish the task of vibration reduction. For verification, a serial of simulations and experimental investigations have been analysed to demonstrate the preferable potentialities of the proposed method. In particular, a standard Bently Nevada rotor rig with a specifically designed device was employed to simulate appended faults by adjusting the additional forces during the experimental steps. The analysis results show that the proposed method can isolate and extract the unbalance faults from the raw vibration signals and achieve accurate correction balancers, where a nearly identical correction angle has been achieved, which indicates that the optimal installation position has been successfully figured out.
- Open Access
- 1 November 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2113 (1) , 012041
Design of high precision mechatronic-hydraulic leveling system for vehicle-mounted radar
In order to improve the control performance of vehicle-mounted radar, a high precision leveling control system is designed through mechatronic-hydraulic integration technology. A leveling method combining angle error leveling method and height error leveling method is designed, and inclinometers are set in the front and rear of the vehicle body platform to effectively eliminate the virtual outrigger phenomenon in the leveling process. The mathematical model of hydraulic system is developed, the fuzzy PID control method is introduced, and the four-point support hydraulic leveling control system is developed by using STM32 microcontroller as the control core. The field test proves that the control system has good control performance, high leveling accuracy, short time, and meets the control requirements of the radar vehicle.
- 1 November 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2113 (1) , 012041
Open AccessDesign of high precision mechatronic-hydraulic leveling system for vehicle-mounted radar
In order to improve the control performance of vehicle-mounted radar, a high precision leveling control system is designed through mechatronic-hydraulic integration technology. A leveling method combining angle error leveling method and height error leveling method is designed, and inclinometers are set in the front and rear of the vehicle body platform to effectively eliminate the virtual outrigger phenomenon in the leveling process. The mathematical model of hydraulic system is developed, the fuzzy PID control method is introduced, and the four-point support hydraulic leveling control system is developed by using STM32 microcontroller as the control core. The field test proves that the control system has good control performance, high leveling accuracy, short time, and meets the control requirements of the radar vehicle.
- 15 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 114-118
Study on Poincare Plot Characteristics of Dynamic Pressure at Outlet of Centrifugal Compressor Based on Edge Crawling Algorithm
Based on crawling algorithm, the characteristics of dynamic pressure at outlet of an 800kW centrifugal compressor are have been captured after analyzing the relationship between the Poincare plot and the dynamic pressure. First, the dynamic pressure of the centrifugal compressor under different working conditions is tested by controlling the opening degree of the anti-surge valve at outlet of the centrifugal compressor. The Poincare diagrams of dynamic pressure are drawn. Then, according edge crawling algorithm, the boundary points in Poincare plot are determined by setting conditions of edge screening. Finally, the correlation between the characteristic parameters of Poincare plots and the working states of compressor are studied. The results show that the Poincare plot of centrifugal compressors are quite different under different working conditions. In stable-state operation, the shape is elliptic. With the system entering deep surge from transition process, the figure gradually elongates along a certain direction and finally forms a rod-shaped structure. As the values of characteristic quantities in the Poincare chart, each characteristic quantity changes dramatically in the transition process. Furthermore, compared with in stable state, the values of LA and SQ increase sharply, while the values of SA, ALS and Ratio drop dramatically in unstable state. This paper can provide a new basis for the identification and prediction of initial surge of centrifugal compressor.
- 15 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 114-118
Study on Poincare Plot Characteristics of Dynamic Pressure at Outlet of Centrifugal Compressor Based on Edge Crawling Algorithm
Based on crawling algorithm, the characteristics of dynamic pressure at outlet of an 800kW centrifugal compressor are have been captured after analyzing the relationship between the Poincare plot and the dynamic pressure. First, the dynamic pressure of the centrifugal compressor under different working conditions is tested by controlling the opening degree of the anti-surge valve at outlet of the centrifugal compressor. The Poincare diagrams of dynamic pressure are drawn. Then, according edge crawling algorithm, the boundary points in Poincare plot are determined by setting conditions of edge screening. Finally, the correlation between the characteristic parameters of Poincare plots and the working states of compressor are studied. The results show that the Poincare plot of centrifugal compressors are quite different under different working conditions. In stable-state operation, the shape is elliptic. With the system entering deep surge from transition process, the figure gradually elongates along a certain direction and finally forms a rod-shaped structure. As the values of characteristic quantities in the Poincare chart, each characteristic quantity changes dramatically in the transition process. Furthermore, compared with in stable state, the values of LA and SQ increase sharply, while the values of SA, ALS and Ratio drop dramatically in unstable state. This paper can provide a new basis for the identification and prediction of initial surge of centrifugal compressor.
- Open Access
- 4 October 2017
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 12 (1) , 152-168
Numerical analysis of aerodynamic damping for a centrifugal impeller
In order to realize the numerical analysis of aerodynamic damping for the centrifugal impellers, a numerical code integrating the flow-structure data transfer, grid deformation and flow simulation under the moving grid system is first developed. To decrease the huge consumptions of CPU time and memory space, the compactly supported radial basis function is adopted to carry out the data transfer and grid deformation, and the alternating digital tree technique is utilized to calculate the wall distances. By the test cases of an oscillating cascade and a centrifugal impeller, the correctness of the code for the flow simulations with moving boundaries and the flow fields in centrifugal impellers is validated. Then taking a centrifugal impeller as the research object, the calculations of aerodynamic damping characteristics were carried out. The results show that, the modal aerodynamic damping ratio has no relationship with the vibrating amplitude under small vibrations. For the disk-dominant vibration mode, the modal aerodynamic damping ratio decreases as the operating point shifts toward the stall point. The aerodynamic damping caused by the backward traveling wave vibration is larger than that by the forward traveling wave vibration.
- 4 October 2017
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 12 (1) , 152-168
Open AccessNumerical analysis of aerodynamic damping for a centrifugal impeller
In order to realize the numerical analysis of aerodynamic damping for the centrifugal impellers, a numerical code integrating the flow-structure data transfer, grid deformation and flow simulation under the moving grid system is first developed. To decrease the huge consumptions of CPU time and memory space, the compactly supported radial basis function is adopted to carry out the data transfer and grid deformation, and the alternating digital tree technique is utilized to calculate the wall distances. By the test cases of an oscillating cascade and a centrifugal impeller, the correctness of the code for the flow simulations with moving boundaries and the flow fields in centrifugal impellers is validated. Then taking a centrifugal impeller as the research object, the calculations of aerodynamic damping characteristics were carried out. The results show that, the modal aerodynamic damping ratio has no relationship with the vibrating amplitude under small vibrations. For the disk-dominant vibration mode, the modal aerodynamic damping ratio decreases as the operating point shifts toward the stall point. The aerodynamic damping caused by the backward traveling wave vibration is larger than that by the forward traveling wave vibration.
- 1 May 2017
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 83, 107-117
Experimental investigation of an active control casing treatment of centrifugal compressors
- 1 May 2017
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 83, 107-117
Experimental investigation of an active control casing treatment of centrifugal compressors
- 1 January 2009
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 22 (04) , 567
Self-Recirculating Casing Treatment for a Radial Compressor
- 1 January 2009
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 22 (04) , 567
Self-Recirculating Casing Treatment for a Radial Compressor