HXHao Xie

Hao Xie

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hao Xie has a total of 19 co-authors. Here are the top co-authors by number of shared publications:

  • Qiulin Tan

    North University of China

    4 shared publications
  • Lei Zhang

    Science and Technology on Electronic Test and Measurement Laboratory, North University of China, Taiyuan, China

    3 shared publications
  • Shuolin Li

    Science and Technology on Electronic Test and Measurement Laboratory, North University of China, Taiyuan, China

    2 shared publications
  • Zhuya Hao

    Science and Technology on Electronic Test and Measurement Laboratory, North University of China, Taiyuan, China

    2 shared publications
  • Hao Wang

    Science and Technology on Electronic Test and Measurement Laboratory and the State Key Laboratory of Dynamic Measurement Technology, North University of China, Taiyuan, China

    1 shared publication
  • Hao Wang

    Science and Technology on Electronic Test and Measurement Laboratory, North University of China 1 , Taiyuan 030051, China

    1 shared publication

Latest Publications

  • Preparation and Performance Evaluation of a Miniature High-Temperature Heat Flux Sensor With Centralized Thermal Insulation Structure

    by Xiaofen Li, Lei Zhang, Hao Xie, Ze Shang, Xiangxiang Zhang, Xue Qi, Meimei Lu, Qiulin Tan

    The internal hot-end components of aero-engines operate in a high–temperature environment are susceptible to cracks or falling blocks owing to thermal fatigue and other effects. The rapid changes in heat flux at these defects can lead to engine failure. We propose a miniaturized sensor capable of monitoring heat flux change in a high-temperature environment. The sensor is based on a thermopile, connected in series with the platinum–10% rhodium/ platinum (Pt–Rh10/Pt) thermocouples as the basic unit on a ceramic plate sized 10 mm × 10 mm × 1 mm. Nanocomposite silicon dioxide is adopted as a thermal insulation material to generate a temperature difference at the hot and cold junctions, which is distributed in the center and results in a thermal voltage output in the millivolt range. The heat flux sensor (HFS) can operate at temperatures up to 1000 °C with a good repeatability. The output voltage at a heat flux of 189.6 kW/m 2 is 0.4113 mV, and the dynamic response time of HFS is 0.25 s. The screen printing process enables the batch preparation of micro heat flux sensors for high-temperature device surfaces with small areas.


  • Effect of AlN/Al2O3 Thin-Film Protective Layer on the High-Temperature Performance of ITO Thin-Film Strain Gauge

    by Shuolin Li, Lei Zhang, Hao Xie, Xue Yao, Zhuya Hao, Helei Dong, Qiulin Tan

    When an ITO thin-film strain gauge is applied on turbine engine blades, a protective layer must be included to prevent the oxidation of the ITO thin-film sensitive material. In this study, an AlN/Al 2 O 3 composite film is prepared as a protective layer on an alumina ceramic sheet using the pulsed laser deposition technique to cover the ITO-sensitive material film. Subsequently, the films are microscopically characterised, and the high-temperature performance of the ITO thin film strain gauge is verified. The results indicate that the AlN/Al 2 O 3 film is dense and crack-free, and that the ITO thin-film strain gauge with the AlN/Al 2 O 3 film acting as the protective layer demonstrates a minimum resistance temperature coefficient of -521 ppm/°C, minimum resistance drift rate of 0.0117 /h, and good cycle repeatability at 1100 °C when compared to an ITO strain gauge without a protective layer and a strain gauge prepared using a single Al 2 O 3 film protective layer. Furthermore, its strain characteristic test at 800°C showed an average gauge factor (GF) of 8.12.


  • Design, Preparation, and Performance Study of a Miniaturized High-Temperature Thick-Film Heat Flux Sensor

    by Hao Xie, Lei Zhang, Xiaofen Li, Shuolin Li, Zhuya Hao, Hao Wang, Jijun Xiong, Qiulin Tan

    Solving heat transfer problems in high-temperature and temperature-changing environments is critical in a variety of applications, including modern turbines, aerospace, and nuclear power plants. However, most current thin-film-type heat flow sensors operate at approximately 1000 °C. Thus, we fabricated a kind of platinum–platinum/rhodium thick-film thermopile-type heat flux sensor which can work stably at 1200 °C based on an alumina ceramic substrate. The entire electrode layer was prepared by screen printing process. The surface morphology of the Pt electrode and the material in thermal resistance layer at different stages were investigated using scanning electron microscopy. The steady-state characteristics of the sensor were evaluated by using a high-temperature test platform. The experiments show that the peak voltage of the sensor is 1.4126 mV at the temperature of 1200 °C and the heat flow density of 283.3 kW/m 2 . Moreover, the repeatability of sensor at 1200 °C and high temperature holding for 4 h experiments were performed, verifying that the sensor has good consistency and durability. Therefore, we infer that the designed sensor can be applied for a long time under high temperature and large heat flow conditions, such as aerospace, mechanical metallurgy and energy construction fields.


  • A wireless demodulation system based on a multi-parameter resonant sensor

    by Hao Wang, Xiaorui Liang, Juan Zhang, Lei Zhang, Hao Xie, Zhongliang Zhao, Qiulin Tan

    This paper proposes a wireless passive measurement system that supports real-time signal acquisition, multi-parameter crosstalk demodulation, and real-time storage and calculation. The system consists of a multi-parameter integrated sensor, an RF signal acquisition and demodulation circuit, and a multi-functional host computer software. The sensor signal acquisition circuit uses a wide frequency detection range (25 MHz–2.7 GHz) to meet the resonant frequency range of most sensors. Since the multi-parameter integrated sensors are affected by multiple factors, such as temperature and pressure, there will be interference between them, so the algorithm for multi-parameter decoupling is designed, and the software for sensor calibration and real-time demodulation is developed to improve the usability and flexibility of the measurement system. In the experiment, temperature and pressure dual-reference integrated surface acoustic wave sensors in the condition of 25–550 °C and 0–700 kPa are used for testing and verification. After experimental testing, the swept source of the signal acquisition circuit can meet the output accuracy in a wide frequency range, and the detection result of the sensor dynamic response is consistent with that of the network analyzer, with a maximum test error of 0.96%. Furthermore, the maximum temperature measurement error is 1.51%, and the maximum pressure measurement error is 5.136%. These results indicate that the proposed system has good detection accuracy and demodulation performance, and it can be used for multi-parameter wireless real-time detection and demodulation.